journal article·2001-08

Decomposition of Fe-intermetallics in Sr-modified cast 6XXX type aluminum alloys for automotive skin

F. H. Samuel, A. M. Samuel, H. W. Doty, S. Valtierra

Publisher page

Abstract

The present study was carried out on two 6XXX type aluminum alloys: an experimental alloy and commercial 6111 alloy, containing Fe, Si, Mn, and Mg as the principal elements, and with Fe/Si ratios of 0.28 and 0.49, respectively. Measured amounts of Sr (up to 1500 ppm) were added to these alloys. The alloy melts were cast in a graphite mold heated at 600 °C (cooling rate ∼0.7 °C s−1). Some of the castings were homogenized for 8 hours at 540 °C. The microstructural constituents were evaluated using thermal analysis and metallographic techniques. The various phases observed were identified using electron probe microanalysis (EPMA) and energy dispersive X-ray (EDX) analysis. Results show that, when the Fe/free Si ratio is <1 (free Si being the Si remaining above that required for Mg2Si formation), addition of Sr (300 to 500 ppm) destabilizes the β-Al5FeSi phase platelets, leading to rejection of Si ahead of the β-platelet/Al matrix interface. Increasing the concentration of Sr (∼800 ppm) leads to the precipitation of a new intermetallic, possibly Al2Si2Sr (in the form of short needles or rods). The iron can react with the Al to form Al6Fe, or with the remaining Si to precipitate as α-Al8Fe2Si in Chinese script form. A new mechanism for the formation of Al2Si2Sr phase has been proposed, based on the possibility that the rejected Si ahead of the destablized β-Al5FeSi platelets reacts with the surrounding Sr and Al to form polygonal (rounded or squarelike) particles of Al2Si2Sr. These particles are normally observed attached to the decomposed β phase (or Al6Fe). During homogenization treatment, the β-Al5FeSi decomposes into Al6Fe and Si. The decomposition takes place much more easily in the Sr-containing alloys. In contrast, both Al2Si2Sr and Al8Fe2Si phases are stable at temperatures as high as 540 °C. The introduction of Mn and Mg to the Al-Fe-Si system (viz., 6111 alloy, with a Fe/free Si ratio of 1.55) results in the precipitation of several Chinese script phases, namely, Al15(Fe,Mn)3Si2, Al8(Fe,Mn)2Si, Al8Mg3FeSi6, and Mg2Si. Compared to the β-Al5FeSi phase, the compositions of these script phases are more stable in the presence of Sr. At higher Sr levels (∼800 ppm or more), partial decomposition of α-Al15(Fe,Mn)3Si2 into Al6.9(Fe,Mn)Si and Si can occur. Fragmentation of the α-Al15(Fe,Mn)3Si2 phase takes place only at Sr concentrations on the order of ∼1500 ppm.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Magnesium Alloys: Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. A. Couture: AFS Int. Cast Met. J., 1981, vol. 6 (4), pp. 9–17.
2. H. Brischel, A. Reid, and J. Langerweger: Aluminium, vol. 57, p. E281.
3. G.K. Sigworth, S. Shivkumar, and D. Aplien: AFS Trans., 1989, vol. 97, pp. 811–24.
4. Aluminum Casting Technology, American Foundrymen’s Society Inc., Des Plaines, IL, 1986.
5. P. Ouellet and F.H. Samuel: J. Mater. Sci., 1999, vol. 34, pp. 4671–97.10.1023/A:1004645928886 ↗
6. M.S. Misra and K.J. Oswalt: AFS Trans., 1980, vol. 90, pp. 1–10.
7. J. Lendvai, T. Ungar, and J. Kovacks: Mater. Sci. Eng., 1963, vol. 10, pp. 151–59.
8. L. Backerud, G. Chai, and J. Tamminen: Solidification Characteristics of Aluminum Alloys, vol. 1: Wrought Alloys, AFS/Skanaluminium, Des Plaines, IL, 1990.
9. L.R. Morris and F.B. Miner: U.S. Patent No. 3,926,690, 1975.
10. F. Paray, B. Kulunk, and J.E. Gruzleski: Mater. Sci. Technol., 1996, vol. 17, pp. 315–22.10.1179/mst.1996.12.4.315 ↗
11. M.H. Mulazimoglu, A. Zaluska, J.E. Gruzleski, and F. Paray: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 929–35.10.1007/BF02649760 ↗
12. G. Farhadi, A.M. Samuel, F.H. Samuel, B. Kulunk, and H.W. Doty: Aluminum Trans., 2001, in press.
13. F.A. Crossley and L.F. Mondolfo: Trans. AIME, 1951, p. 114310.1007/BF03397424 ↗
14. also V.G. Rivlin and G.V. Raynor: Int. Met. Rev., 1981, vol. 3, p. 133.10.1179/imtr.1981.26.1.133 ↗
15. D.J. Lloyd and A.K. Gupta: Int. Conf. on “Thermomechanical Processing of Steels & Other Materials”, T. Chandra and T. Sakai, eds, TMS, Warrendale, PA, 1997, pp. 99–107.
16. A.M. Samuel, A. Pennors, C. Villeneuve, F.H. Samuel, H.W. Doty, and S. Valtierra: Int. J. Cast. Metals. Res., 2000, vol. 13, pp. 231–53.10.1080/13640461.2000.11819406 ↗
17. Constitution of Binary Alloys, M. Hansen, ed., McGraw-Hill Book Company, Inc., New York, NY, 1958.
18. G.H. Westengen: Z. Metallkd., 1982, vol. 73, pp. 360–68.
19. Aluminum Properties and Physical Metallurgy, J.E. Hatch, ed., ASM INTERNATIONAL, Metals Park, OH, 1984, p. 140.
20. L. Liu, A.M. Samuel, F.H. Samuel, H.W. Doty, and S. Valtierra: unpublished data, UQAC(University of Quebec at Chicoutimi), 2001.
21. F.H. Samuel, G. Pucella, C. Villeneuve, A.M. Samuel, H.W. Doty, and S. Valtierra: Int. J. Cast. Metals Res., 1999, vol. 12, pp. 197–210.10.1080/13640461.1999.11819357 ↗