journal article·2005-11

Crystal-plasticity analysis of ridging in ferritic stainless steel sheets

Olaf Engler, Moo-Young Huh, Carlos N. Tomé

Publisher page

Abstract

The occurrence of ridging in ferritic stainless steel (FSS) sheets is caused by the collective deformation of bandlike clusters of grains with a similar crystallographic orientation. In this article, largescale (1.8×3.6 mm) orientation maps obtained by electron backscattered diffraction (EBSD) are input into a viscoplastic self-consistent polycrystal plasticity model to analyze the strain anisotropy caused by the topographic arrangement of the recrystallization-texture orientations. Two versions of the ridging model were devised: (1) the local dispersion in strain-rate components is analyzed for the full EBSD map, and (2) narrow bands in the EBSD maps aligned parallel to the ridges on the sheet surface are considered, and the variation in macroscopic strain response from band to band is derived. The effects caused by spatial variations in through-thickness strains and in out-of-plane shears are compared and related to ridging. The model is applied to two sheets distinguished by different levels of ridging.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Metal Forming Simulation Techniques · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. H.C. Chao: Trans. ASM, 1967, vol. 60, pp. 37–50.
2. R.N. Wright: Metall. Trans., 1972, vol. 3, pp. 83–91.10.1007/BF02680588 ↗
3. H. Takechi, H. Kato, T. Sunami, and T. Nakayama: Trans. JIM, 1967, vol. 31, pp. 717–23.
4. T. Sheppard and P. Richards: Mater. Sci. Technol., 1986, vol. 2, pp. 693–99.10.1179/mst.1986.2.7.693 ↗
5. J.A. Salsgiver, J.M. Larsen, and P.R. Borneman: Recrystallization ’90, T. Chandra, ed., TMS, Warrendale PA, 1990, pp. 849–54.
6. H.M. Kim and J.A. Szpunar: Mater. Sci. Forum, 1994, vols. 157–162, pp. 753–60.10.4028/www.scientific.net/MSF.157-162.753 ↗
7. D. Raabe and K. Lücke: Mater. Sci. Technol., 1993, vol. 9, pp. 302–12.10.1179/mst.1993.9.4.302 ↗
8. Y. Shimizu, Y. Ito, and Y. Iida: Metall. Trans. A, 1986, vol. 17A, pp. 1323–34.10.1007/BF02650113 ↗
9. N. Tsuji, K. Tsuzaki, and T. Maki: Iron Steel Inst. Jpn. Int., 1994, vol. 34, pp. 1008–17.10.2355/isijinternational.34.1008 ↗
10. H.-G. Appel and H. Becker: Z. Metallkd., 1963, vol. 54, pp. 724–28.
11. M. Arakawa, S. Takemura, and T. Ooka: Trans. Iron Steel Inst. Jpn., 1971, vol. 11, pp. 890–94.
12. M.Y. Huh and O. Engler: Mater. Sci. Eng. A, 2001, vol. A308, pp. 74–87.10.1016/S0921-5093(00)01995-X ↗
13. M.Y. Huh, J.H. Lee, S.H. Park, O. Engler, and D. Raabe: Steel Res. Int., 2005, in press.
14. V. Randle and O. Engler: Introduction to Texture Analysis: Macrotexture, Microtexture and Orientation Mapping, Gordon and Breach Science Publishers, Amsterdam, 2000.10.1201/9781482287479 ↗
15. K. Bethke, M. Hölscher, and K. Lücke: Mater. Sci. Forum, 1994, vols. 157–162, pp. 1137–44.10.4028/www.scientific.net/MSF.157-162.1137 ↗
16. M. Brochu, T. Yokota, and S. Satoh: Iron Steel Inst. Jpn. Int., 1997, vol. 37, pp. 872–77.10.2355/isijinternational.37.872 ↗
17. S.H. Park, W.Y. Kim, Y.D. Lee, and C.G. Park: Iron Steel Inst. Jpn. Int., 2002, vol. 42, pp. 100–05.10.2355/isijinternational.42.100 ↗
18. H.J. Shin, J.K. An, S.H. Park, and D.N. Lee: Acta Mater., 2003, vol. 51, pp. 4693–4706.10.1016/S1359-6454(03)00187-3 ↗
19. A.J. Beaudoin, J.D. Bryant, and D.A. Korzekwa: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 2323–31.10.1007/s11661-998-0109-y ↗
20. D. Raabe, M. Sachtleber, H. Weiland, G. Scheele, and Z. Zhao: Acta Mater., 2003, vol. 51, pp. 1539–60.10.1016/S1359-6454(02)00557-8 ↗
21. P.D. Wu, D.J. Lloyd, A. Bosland, H. Jin, and S.R. MacEwen: Acta Mater., 2003, vol. 51, pp. 1945–57.10.1016/S1359-6454(02)00600-6 ↗
22. Z. Zhao, R. Radovitzky, and A. Cuitiño: Acta Mater., 2004, vol. 52, pp. 5791–5804.10.1016/j.actamat.2004.08.037 ↗
23. R.D. Knutsen and N.J. Wittridge, Mater. Sci. Technol., 2002, vol. 18, pp. 1279–85.10.1179/026708302225007457 ↗
24. R.A. Lebensohn and C.N. Tomé: Acta Metall. Mater., 1993, vol. 41, pp. 2611–24.10.1016/0956-7151(93)90130-K ↗
25. C.N. Tomé and R.A. Lebensohn: in Continuum Scale Simulation of Engineering Materials: Fundamentals, Microstructures, Process Applications, D. Raabe, F. Roters, F. Barlat, and L.Q. Chen, eds., Wiley-VCH, Weinheim, Germany, 2004, pp. 473–99.10.1002/3527603786.ch23 ↗
26. C.N. Tomé: Model. Simul. Mater. Sci. Eng., 1999, vol. 7, pp. 723–38.10.1088/0965-0393/7/5/305 ↗