journal article·2008-06

Low-Temperature Aging Characteristics of Type 316L Stainless Steel Welds: Dependence on Solidification Mode

Hiroshi Abe, Yutaka Watanabe

Publisher page

Abstract

Thermal aging embrittlement of light water reactor (LWR) components made of stainless steel cast has been recognized as a potential degradation issue, and careful attention has been paid to it. Although welds of austenitic stainless steels have γ-δ duplex microstructure, which is similar to that of the stainless steel cast, examination of the thermal aging characteristics of the stainless steel welds is very limited. In this investigation, two types of type 316L stainless steel weld metal with different solidification modes were prepared using two kinds of filler metals having tailored Ni equivalent and Cr equivalent. Differences between the two weld metals in the morphology of microstructure, in the composition of δ-ferrite, and in hardening behaviors with isothermal aging at 335 °C have been investigated. The hardness of the ferrite phase has increased with aging time, while the hardness of austenite phase has stayed the same. The mottled aspect has been observed in δ-ferrite of aged samples by transmission electron microscopy (TEM) observation. These characteristics suggest that spinodal decomposition has occurred in δ-ferrite by aging at 335 °C. The age-hardening rate of δ-ferrite was faster for the primary austenite solidification mode (AF mode) sample than the primary ferrite solidification mode (FA mode) sample in the initial stage of the aging up to 2000 hours. It has been suggested that the solidification mode can affect the kinetics of spinodal decomposition.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. M.K. Miller and J. Bentley: Proc. 3rd Conf. on Environmental Degradation of Materials in Nuclear Power Systems—Water Reactors, TMS-AIME, Warrendale, PA, 1988, pp. 341–49
2. H.M. Chung, T.R. Leax: Mater. Sci. Technol., 1990, vol. 6, pp. 249–6210.1179/mst.1990.6.3.249 ↗
3. P. Auger, F. Danoix, A. Menand, S. Bonnet, J. Bourgoin, M. Guttamann: Mater. Sci. Technol., 1990, vol. 6, pp. 301–1310.1179/mst.1990.6.3.301 ↗
4. P.H. Pumphrey, K.H. Akhurst: Mater. Sci. Technol., 1990, vol. 6, pp. 211–1910.1179/mst.1990.6.3.211 ↗
5. N. Suutala, T. Taklo, T. Moisio: Metall. Trans. A, 1979, vol. 10A, pp. 512–1410.1007/BF02697081 ↗
6. J.A. Brooks, M.I. Baskes, F.A. Greulich: Metall. Trans. A, 1991, vol. 22A, pp. 915–2610.1007/BF02659001 ↗
7. N. Suutala, T. Taklo, T. Moisio: Metall. Trans. A, 1980, vol. 11A, pp. 717–2510.1007/BF02661201 ↗
8. H.M. Chung and O.K. Chopra: Proc. 3rd Conf. on Environmental Degradation of Materials in Nuclear Power Systems-Water Reactors, TMS-AIME, Warrendale, PA, 1988, pp. 359–70
9. K.L. Weng, H.R. Chen, J.R. Yang: Mater. Sci. Eng. A, 2004, vol. 379, pp. 119–3210.1016/j.msea.2003.12.051 ↗
10. J.J. Shiao, C.H. Tsai, J.J. Kai, J.H. Huang: J. Nucl. Mater., 1994, vol. 217, pp. 269–7810.1016/0022-3115(94)90376-X ↗
11. M. Vrinat, R. Cozar, and Y. Meyzaud: Scripta Metall., 1986, No. 8, pp. 1101–0610.1016/0036-9748(86)90183-3 ↗
12. J.M. Vitek: Metall. Trans. A, 1987, vol. 18A, pp. 154–5610.1007/BF02646233 ↗
13. A. Mateo, L. Llanes, and M. Anglada: J. Mater. Sci., 1997, No. 32, pp. 4533–4010.1023/A:1018669217124 ↗
14. T. Yoshimura, Y. Ishikawa: ASME PED, 1990, vol. 46, pp. 77–88
15. H.M. Chung: ASME PVP, 1989, vol. 171, pp. 111–25
16. P. Koutaniemi, V. Heikkinen, A. Saarinen, Metall. Sci., 1974, vol. 8, pp. 94–9610.1179/msc.1974.8.1.94 ↗
17. A. Hendry, Z.F. Mazur, K.H. Jack: Metall. Sci., 1979, vol. 13, pp. 482–8610.1179/030634579790438327 ↗
18. H.D. Solomon, L.M. Levinson: Acta Metall., 1978, vol. 26, pp. 429–4210.1016/0001-6160(78)90169-4 ↗