Strain-path effects on the evolution of microstructure and texture during the severe-plastic deformation of aluminum
Source abstract
Abstract
Microstructure and texture evolution during the severe-plastic deformation (SPD) of unalloyed aluminum were investigated to establish the effect of processing route and purity level on grain refinement and subgrain formation. Two lots of aluminum with different purity levels (99.998 pct Al and 99 pct Al) were subjected to large plastic strains at room temperaturevia four different deformation processes: equal-channel angular extrusion (ECAE), sheet rolling, conventional conical-die extrusion, and uniaxial compression. Following deformation, microstructures and textures were determined using orientation-imaging microscopy. In commercial-purity aluminum, the various deformation routes yielded an ultrafine microstructure with a ∼1.5-µm grain size, deduced to have been formedvia a dynamic-recovery mechanism. For high-purity aluminum, on the other hand, the minimum grain size produced after the various routes was ∼20 µm; the high fraction of high-angle grain boundaries (HAGBs) and the absence of subgrains/deformation bands in the final microstructure suggested the occurrence of discontinuous static recrystallization following the large plastic deformation at room temperature. The microstructure differences were underscored by the mechanical properties following four ECAE passes. The yield strength of commercial-purity aluminum quadrupled, whereas the high-purity aluminum showed only a minor increase relative to the annealed condition.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Metallurgy and Material Forming · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (58)
Show source-provided references
1. V.M. Segal, V.I. Reznikov, A.E. Drobyshevskiy, and V.I. Kopylov:Russ. Metall., 1981, vol. 1, pp. 99–105.
2. R.Z. Valiev, N.A. Krasilnikov, and N.K. Tsenev:Mater. Sci. Eng, 1991, vol. A137, pp. 35–40.10.1016/0921-5093(91)90316-F ↗
3. R.Z. Valiev, A.V. Korznikov, and R.R. Mulyukov:Mater. Sci. Eng, 1993, vol. A168, pp. 141–48.10.1016/0921-5093(93)90717-S ↗
4. V.M. Segal:Mater. Sci. Eng., 1995, vol. A197, pp. 157–64.10.1016/0921-5093(95)09705-8 ↗
5. R.Z. Valiev, R.K. Islamgaliev, and I.V. Alexandrov:Progr. Mater. Sci., 2000, vol. 45, pp. 103–89.10.1016/S0079-6425(99)00007-9 ↗
6. F.J. Humphreys, P.B. Prangnell, and R. Priestner:Curr. Opin. Solid State Mater. Sci., 2001, vol. 5, pp. 15–21.10.1016/S1359-0286(00)00020-6 ↗
7. S. Gourdet and F. Montheillet:Mater. Sci. Eng, 2000, vol. A283, pp. 274–88.10.1016/S0921-5093(00)00733-4 ↗
8. M. Furukawa, Y. Iwahashi, Z. Horita, M. Nemoto, and T.G. Langdon:Mater. Sci. Eng, 1998, vol. A257, pp. 328–32.10.1016/S0921-5093(98)00750-3 ↗
9. K. Oh-Ishi, Z. Horita, M. Furukawa, M. Nemoto, and T.G. Langdon:Metall. Mater. Trans. A, 1998, vol. A29, pp. 2011–13.10.1007/s11661-998-0027-z ↗
10. P.B. Prangnell, A. Gholinia, and M.V. Markushev: inInvestigations and Applications of Severe Plastic Deformation, T.C. Lowe and R.Z Valiev, eds., Kluwer Academic Publishers, Dordrecht, The Netherlands, 2000, pp. 65–71.10.1007/978-94-011-4062-1_9 ↗
11. Y.T. Zhu and T.C. Lowe:Mater. Sci. Eng., 2000, vol. A291, pp. 46–53.10.1016/S0921-5093(00)00978-3 ↗
12. M. Furukawa, Z. Horita, and T.G. Langdon:Mater. Sci. Eng., 2002, vol. A332, pp. 97–109.10.1016/S0921-5093(01)01716-6 ↗
13. N. Hansen, X. Huang, and D.A. Hughes: inUltrafine Grained Materials II, Y.T. Zhu, T.G. Langdon, R.S. Mishra, S.L. Semiatin, M.J. Saran, and T.C. Lowe, eds., TMS, Warrendale, PA, 2002, pp. 3–14.
14. P.J. Hurley and F.J. Humphreys:Acta Mater., 2003, vol. 51, pp. 1087–102.10.1016/S1359-6454(02)00513-X ↗
15. S.L. Semiatin and D.P. DeLo:Mater. Des., 2000, vol. 21, pp. 311–22.10.1016/S0261-3069(99)00085-0 ↗
16. Y. Iwahashi, M. Furukawa, Z. Horita, M. Nemoto, and T.G. Langdon:Metall. Mater. Trans. A, 1998, vol. 29A, pp. 2245–52.10.1007/s11661-998-0102-5 ↗
17. Y. Iwahashi, Z. Horita, M. Nemoto, and T.G. Langdon:Acta Mater., 1998, vol. 46, pp. 3317–31.10.1016/S1359-6454(97)00494-1 ↗
18. G. Langford and M. Cohen:Metall. Trans. A, 1975, vol. 6A, pp. 901–10.10.1007/BF02672314 ↗
19. J. Gil Sevillano, P. Van Houte, and E. Aernoudt:Progr. Mater. Sci., 1981, vol. 25, pp. 69–412.10.1016/0079-6425(80)90001-8 ↗
20. Y. Iwahashi, Z. Horita, M. Nemoto, and T.G. Langdon:Acta Mater., 1997, vol. 45, pp. 4733–41.10.1016/S1359-6454(97)00100-6 ↗
21. T.R. McNelley, D.L. Swisher, Z. Horita, and T.G. Langdon: inUltrafine Grained Materials II, Y.T. Zhu, T.G. Langdon, R.S. Mishra, S.L. Semiatin, M.J. Saran, and T.C. Lowe, eds., TMS, Warrendale, PA, 2002, pp. 15–23.10.1002/9781118804537.ch2 ↗
22. S.D. Terhune, D.L. Swisher, K. Oh-Ishi, T.G. Langdon, and T.R. McNelley:Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2173–84.10.1007/s11661-002-0049-x ↗
23. D. Hardwick, C.M. Sellars, and W.J. McG. Tegart:J. Inst. Met., 1961–62, vol. 90 (21) pp. 21–23.
24. H.J. McQueen and K. Conrad: inMicrostructural Control in Al Alloys Processing, H. Chin and H.J. McQueen, eds., TMS-AIME, Warrendale, PA, 1986, pp. 197–219.
25. H. Yamagata:Scripta Metall. Mater., 1992, vol. 27, pp. 201–03.10.1016/0956-716X(92)90113-S ↗
26. H. Yamagata:Scripta Metall. Mater., 1992, vol. 27, pp. 727–32.10.1016/0956-716X(92)90496-2 ↗
27. H. Yamagata:Scripta Metall. Mater., 1992, vol. 27, pp. 1157–60.10.1016/0956-716X(92)90591-2 ↗
28. H. Yamagata:Scripta Metall. Mater., 1992, vol. 30, pp. 411–16.10.1016/0956-716X(94)90595-9 ↗
29. H. Yamagata:Acta Metall. Mater., 1995, vol. 43, pp. 723–29.10.1016/0956-7151(94)00267-L ↗
30. D. Ponge, M. Bredehoft, and G. Gottstein:Scripta Metall. Mater., 1997, vol. 37, pp. 1769–75.10.1016/S1359-6462(97)00346-1 ↗
31. C. Chovet, S. Gourdet, and F. Montheillet:Proc. Int. Conf. UHPM 98, Sevrier Annecy Lake, France, 1998, pp. 67–74.
32. D. Yamaguchi, Z. Horita, M. Nemoto, and T.G. Langdon:Scripta Mater., 1999, vol. 41, pp. 791–96.10.1016/S1359-6462(99)00233-X ↗
33. H. Hasegawa, S. Komura, A. Utsunomiya, Z. Horita, M. Furukawa, M. Nemoto, and T.G. Langdon:Mater. Sci. Eng. A., 1999, vol. A265, pp. 188–96.10.1016/S0921-5093(98)01136-8 ↗
34. Q. Liu, X. Huang, D.J. Lloyd, and N. Hansen:Acta Mater., 2002, vol. 50, pp. 3789–802.10.1016/S1359-6454(02)00174-X ↗
35. L. Delannay, O.V. Mishin, D. Juul Jensen, and P. Van Houtte:Acta Mater., 2001, vol. 49, pp. 2441–51.10.1016/S1359-6454(01)00150-1 ↗
36. U.F. Kocks:J. Eng. Mater. Technol., 1976, vol. 98, pp. 76–85.10.1115/1.3443340 ↗
37. H. Mecking and U.F. Kocks:Acta Metall. Mater., 1981, vol. 29, pp. 1865–75.10.1016/0001-6160(81)90112-7 ↗
38. Y. Estrin and H. Mecking:Acta Metall. Mater., 1984, vol. 32, pp. 57–70.10.1016/0001-6160(84)90202-5 ↗
39. G. Gottstein and A.S. Argon:Acta Metall. Mater., 1987, vol. 35, pp. 1261–71.10.1016/0001-6160(87)90007-1 ↗
40. H. Mughrabi:Acta Metall. Mater., 1983, vol. 31, pp. 1367–79.10.1016/0001-6160(83)90007-X ↗
41. F.B. Prinz:Acta Metall. Mater., 1984, vol. 32, pp. 1021–28.10.1016/0001-6160(84)90004-X ↗
42. H. Mughrabi:Mater. Sci. Eng., 1987, vol. 85, pp. 15–31.10.1016/0025-5416(87)90463-0 ↗
43. M. Zehetbauer and V. Seumer:Acta Metall. Mater., 1993, vol. 41, pp. 577–88.10.1016/0956-7151(93)90088-A ↗
44. M. Zehetbauer:Acta Metall. Mater., 1993, vol. 41, pp. 589–99.10.1016/0956-7151(93)90089-B ↗
45. A.S. Argon and P. Haasen:Acta Metall. Mater., 1993, vol. 41, pp. 3289–306.10.1016/0956-7151(93)90058-Z ↗
46. Y. Estrin, L.S. Toth, A. Molinari, and Y. Brechet:Acta Mater., 1998, vol. 46, pp. 5509–22.10.1016/S1359-6454(98)00196-7 ↗
47. M. Goeordeler and G. Gottstein:Mater. Sci. Eng. A, 2001, vols. A309–A310, pp. 377–81.10.1016/S0921-5093(00)01728-7 ↗
48. A. Yoshie, H. Morikawa, and Y. Onoe:Trans. Iron Steel Inst. Jpn., 1987, vol. 27, pp. 425–31.10.2355/isijinternational1966.27.425 ↗
49. A. Laasraoui and J.J. Jonas:Metall. Trans A, 1991, vol. 22A, pp. 1545–58.10.1007/BF02667368 ↗
50. W.H. Press, S.A. Teukolsky, W.T. Vetterling, and B.P. Flannery:Numerical Recipes in Fortran 77, Cambridge University Press, New York, NY, 1992, pp. 678–83.
51. N.Q. Chinh, G. Horvath, Z. Horita, and T.G. Langdon:Acta Mater., 2004, vol. 52, pp. 3555–63.10.1016/j.actamat.2004.04.009 ↗
52. Y.M. Wang and E. Ma:Mater. Sci. Eng., 2004, vols. A375–A377, pp. 46–52.10.1016/j.msea.2003.10.214 ↗
53. B. Peeters, M. Seefeldt, C. Teodosiu, S.R. Kalidindi, P. Van Houtte, and E. Aernoudt:Acta Mater., 2001, vol. 49, pp. 1607–19.10.1016/S1359-6454(01)00066-0 ↗
54. G.I. Taylor:J. Inst. Met., 1938, vol. 62, pp. 307–24.
55. S.R. Kalidindi, C.A. Brokhorst, and L. Anand:J. Mech. Phys. Solids, 1992, vol. 40, pp. 537–69.10.1016/0022-5096(92)80003-9 ↗
56. V. Bachu and S.R. Kalidindi:Mater. Sci. Eng., 1998, vol. A257, pp. 108–17.10.1016/S0921-5093(98)00828-4 ↗
57. A. Bhattacharyya, E. El-Danaf, S.R. Kalidindi, and R.D. Doherty:Int. J. Plasticity, 2001, vol. 17, pp. 861–83.10.1016/S0749-6419(00)00072-3 ↗
58. A. Gholinia, P.B. Prangnell, and M.V. Markushev:Acta Mater., 2000, vol. 48, pp. 1115–30.10.1016/S1359-6454(99)00388-2 ↗