journal article·2006-07

A microtexture investigation of recrystallization during friction stir processing of as-cast NiAl bronze

Keiichiro Oh-Ishi, Alexander P. Zhilyaev, Terry R. McNelley

Publisher page

Abstract

As-cast NiAl bronze (NAB) was subjected to friction stir processing (FSP). Orientation imaging microscopy (OIM) methods were used to obtain microtexture data in the stir zone (SZ) and along its periphery. At selected SZ locations, orientation data were obtained by convergent beam electron diffraction (CBED) methods in transmission electron microscopy (TEM). Random α phase textures were apparent in the SZ. The α grains tended to be equiaxed, exhibited annealing twins, and were refined to 1 to 2 µm at the edge of the SZ. The population of subgrain boundaries in α phase grains was highest near the plate surface in contact with the tool and decreased with depth in the SZ, reflecting deformation by the tool shoulder after the passage of the tool pin. Distinct shear texture components were apparent in the thermomechanically affected zone (TMAZ) outside of and along the periphery of the SZ. A texture gradient from the TMAZ into the SZ was apparent and was steeper on the advancing side and under the SZ center than on the retreating side. The apparent shear plane tended to align with the local interface between the SZ and TMAZ, while the shear direction tended to align with the FSP traversing direction. In this material, the SZ-TMAZ interface is a distinct boundary between recrystallized and deformed regions and the α-phase grain refinement reflects dynamic recrystallization and, in locations near the SZ-TMAZ interface, particle-stimulated nucleation (PSN) at undissolved Fe3Al particles.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Metallurgy and Material Science · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. W.M. Thomas, E.D. Nicholas, J.C. Needham, M.G. Murch, P. Templesmith, and C.J. Daws: G.B. Patent Application No. 9125978.8, Dec. 1991
2. U.S. Patent No. 5460317, Oct. 1995.
3. R.S. Mishra:Adv. Mater. Processes, 2003, vol. 161 (10), pp. 43–46.
4. R.S. Mishra, Z.Y. Ma, and I. Charit:Mater. Sci. Eng. A, 2003, vol. A341, pp. 307–10.10.1016/S0921-5093(02)00199-5 ↗
5. Z.Y. Ma, R.S. Mishra, and M.W. Mahoney: inFriction Stir Welding and Processing II, K.V. Jata, M.W. Mahoney, R.S. Mishra, S.L. Semiatin, and T. Lienert, eds., TMS, Warrendale, PA, 2003, pp. 221–30.
6. R.S. Mishra, M.W. Mahoney, S.X. McFadden, N.A. Mara, and A.K. Mukherjee:Scripta Mater., 2000, vol. 42, pp. 163–68.10.1016/S1359-6462(99)00329-2 ↗
7. R.S. Mishra and M.W. Mahoney: inSuperplasticity in Advanced Materials — Proc. ICSAM2000, N. Chandra, ed., Materials Science Forum, Trans Tech Publications, Aedermannsdorf, Switzerland, 2001, vols. 357–359, pp. 507–14.
8. Z.Y. Ma, R.S. Mishra, and M.W. Mahoney:Acta Mater., 2002, vol. 50, pp. 4419–30.10.1016/S1359-6454(02)00278-1 ↗
9. I. Charit and R.S. Mishra:Mater. Sci. Eng., A, 2003, vol. A359, pp. 290–96.10.1016/S0921-5093(03)00367-8 ↗
10. Z.Y. Ma, R.S. Mishra, M.W. Mahoney, and R. Grimes:Mater. Sci. Eng. A, 2003, vol. A351, pp. 148–53.10.1016/S0921-5093(02)00824-9 ↗
11. Y.S. Sato, M. Urata, and H. Kokawa:Metall. Mater. Trans. A, 2002, vol. 33A, pp. 625–35.10.1007/s11661-002-0124-3 ↗
12. S.H.C. Park, Y.S. Sato, and H. Kokawa:Scripta Mater., 2003, vol. 49, pp. 161–66.10.1016/S1359-6462(03)00210-0 ↗
13. D. Zhang, M. Suzuki, and K. Maruyama:Scripta Mater., 2005, vol. 52, pp. 899–903.10.1016/j.scriptamat.2005.01.003 ↗
14. H.S. Park, T. Kimura, T. Murakami, Y. Nagano, K. Nakata, and M. Ushio:Mater. Sci. Eng., A, 2004, vol. A371, pp. 160–69.10.1016/j.msea.2003.11.030 ↗
15. Y.S. Sato, T.W. Nelson, and C.J. Sterling:Acta Mater., 2005, vol. 53, pp. 637–45.10.1016/j.actamat.2004.10.017 ↗
16. A.P. Reynolds, E. Hood, and W. Tang:Scripta Mater., 2005, vol. 52, pp. 491–94.10.1016/j.scriptamat.2004.11.009 ↗
17. M.W. Mahoney, W.H. Bingel, S.R. Sharma, and R.S. Mishra:Mater. Sci. Forum, 2003, vol. 426–4, pp. 2843–48.10.4028/www.scientific.net/MSF.426-432.2843 ↗
18. K. Oh-ishi, A.P. Zhilyaev, R. Williams, and T.R. McNelley: inFriction Stir Welding and Processing III, K.V. Jata, M.W. Mahoney, R.S. Mishra, and T.J. Lienert, eds., TMS, Warrendale, PA, 2005, pp. 107–14.
19. I. Charit and R.S. Mishra:Acta Mater., 2005, vol. 53, pp. 4211–23.10.1016/j.actamat.2005.05.021 ↗
20. K. Oh-ishi and T.R. McNelley:Metall. Mater. Trans. A, 2004, vol. 35A, pp. 2951–61.10.1007/s11661-004-0242-1 ↗
21. K. Oh-ishi and T.R. McNelley:Metall. Mater. Trans. A, 2005, vol. 36A, pp. 1575–85.10.1007/s11661-005-0249-2 ↗
22. J.L. Robbins, O.C. Shepard, and O.D. Sherby:J. Iron Steel Inst., 1964, vol. 202, pp. 804–07.
23. O.D. Sherby, B. Walser, C.M. Young, and E.M. Cady:Scripta Metall., 1975, vol. 9, pp. 569–74.10.1016/0036-9748(75)90352-X ↗
24. B. Walser and O.D. Sherby:Metall. Trans. A, 1979, vol. 10A, pp. 1461–71.10.1007/BF02812011 ↗
25. Y.S. Sato, H. Kokawa, K. Ikeda, M. Enomoto, S. Jogan, and T. Hashimoto:Metall. Mater. Trans. A, 2001, vol. 32A, pp. 941–48.10.1007/s11661-001-0351-z ↗
26. D.P. Field, T.W. Nelson, Y. Hovanski, and K.V. Jata:Metall. Mater. Trans. A, 2001, vol. 32A, pp. 2869–77.10.1007/s11661-001-1037-2 ↗
27. R.W. Fonda, J.F. Bingert, and K.J. Colligan:Scripta Mater., 2004, vol. 51, pp. 243–48.10.1016/j.scriptamat.2004.04.017 ↗
28. S.H.C. Park, Y.S. Sato, and H. Kokawa:Metall. Mater. Trans. A, 2003, vol. 34A, pp. 987–94.10.1007/s11661-003-0228-4 ↗
29. P. Brezina:Int. Met. Rev., 1982, vol. 27, pp. 77–120.10.1179/imr.1982.27.1.77 ↗
30. F. Hasan, A. Jahanafrooz, G.W. Lorimer, and N. Ridley:Metall. Trans. A, 1982, vol. 13A, pp. 1337–45.10.1007/BF02642870 ↗
31. A. Jahanafrooz, F. Hasan, G.W. Lorimer, and N. Ridley:Metall. Trans. A, 1983, vol. 14A, pp. 1951–56.10.1007/BF02662362 ↗
32. P.B. Prangnell and C.P. Heason:Acta Mater., 2005, vol. 53, pp. 3179–92.10.1016/j.actamat.2005.03.044 ↗
33. J.K. MacKenzie:Biometrika, 1958, vol. 45, pp. 229–40.10.1093/biomet/45.1-2.229 ↗
34. V. Randle and O. Engler:Introduction to Texture Analysis: Macrotexture, Microtexture & Orientation Mapping, Gordon and Breach, Amsterdam, The Netherlands, 2000, pp. 138 and 226.10.1201/9781482287479 ↗
35. G.R. Canova, U.F. Kocks, and J.J. Jonas:Acta Metall., 1984, vol. 32, pp. 211–26.10.1016/0001-6160(84)90050-6 ↗
36. K.N. Krishnan:Mater. Sci. Eng., A, 2002, vol. 327, pp. 246–51.10.1016/S0921-5093(01)01474-5 ↗
37. R.D. Doherty, D.A. Hughes, F.J. Humphreys, J.J. Jonas, D. Juul-Jensen, M.E. Kassner, W.E. King, T.R. McNelley, H.J. McQueen, and A.D. Rollett:Mater. Sci. Eng., A, 1997, vol. A238, pp. 219–74.10.1016/S0921-5093(97)00424-3 ↗
38. F.J. Humphreys:Acta Metall., 1977, vol. 25, pp. 1323–44.10.1016/0001-6160(77)90109-2 ↗
39. J. Askill:Tracer Diffusion Data for Metals, Alloys and Simple Oxides, IFI Plenum, New York, NY, 1970, pp. 32–45.10.1007/978-1-4684-6075-9 ↗
40. A. Askari, S. Silling, B. London, and M.W. Mahoney: inFriction Stir Welding and Processing, K.V. Jata, M.W. Mahoney, R.S. Mishra, S.L. Semiatin, and D.P. Fields, eds., TMS, Warrendale, PA, 2001, pp. 43–50.