journal article·2004-09

A thousandfold creep strengthening by Ca addition in die-cast AM50 magnesium alloy

Yoshihiro Terada, Rie Sota, Naoya Ishimatsu, Tatsuo Sato, Koichi Ohori

Publisher page

Abstract

The effect of calcium addition on the microstructure and creep strength of the die-cast AM50 magnesium alloy was investigated. The α-Mg grains with the diameter of 4.9 µm are surrounded by the eutectic phases for the AM50-1.72 mass pct Ca alloy, while the β(Mg17Al12) particles are located mainly on the grain boundaries of the α grains for the AM50 alloy. The minimum creep rates of the AM50-1.72 mass pct Ca alloy are three orders of magnitude lower than those of the AM50 alloy at 423 K typically below 120 MPa. The thousandfold creep strengthening by the Ca addition is ascribed to the thermally stable eutectic phases appearing in the AM50-1.72 mass pct Ca alloy, which is expected to yield effective grain boundary strengthening or to resist the plastic flow of the α-Mg grains.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. W. Blum, P. Weidinger, B. Watzinger, R. Sedlacek, R. Rosch, and H.-G. Haldenwanger: Z. Metallkd., 1997, vol. 88, pp. 636–41.
2. B.L. Mordike and T. Ebert: Mater. Sci. Eng. A, 2001, vol. A302, pp. 37–45.10.1016/S0921-5093(00)01351-4 ↗
3. T. Kaneko and M. Suzuki: Mater. Sci. Forum, 2003, vols. 419–422, pp. 67–72.10.4028/www.scientific.net/MSF.419-422.67 ↗
4. A. Luo and M.O. Pekguleryuz: J. Mater. Sci., 1994, vol. 29, pp. 5259–71.10.1007/BF01171534 ↗
5. W.K. Miller: Metall. Trans. A, 1991, vol. 22A, pp. 873–77.10.1007/BF02658997 ↗
6. A.A. Luo, M.P. Balogh, and B.R. Powell: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 567–74.10.1007/s11661-002-0118-1 ↗
7. H. Gjestland, G. Nussbaum, G. Regazzoni, O. Lohne, and O. Bauger: Mater. Sci. Eng. A, 1991, vol. A134, pp. 1197–200.10.1016/0921-5093(91)90954-L ↗
8. R. Ninomiya, T. Ojiro, and K. Kubota: Acta Metall. Mater., 1995, vol. 43, pp. 669–74.10.1016/0956-7151(94)00269-N ↗
9. D. Wenwen, S. Yangshan, M. Xuegang, X. Feng, Z. Min, and W. Dengyun: Mater. Sci. Eng. A, 2003, vol. A356, pp. 1–7.10.1016/S0921-5093(02)00551-8 ↗
10. H. Westengen: Science and Engineering of Light Metals, The Japan Institute of Light Metals, Tokyo, 1991, pp. 77–84.
11. I.J. Polmear: Mater. Sci. Technol., 1994, vol. 10, pp. 1–16.10.1179/mst.1994.10.1.1 ↗
12. R.M. Wang, A. Eliezer, and E.M. Gutman: Mater. Sci. Eng. A, 2003, vol. A355, pp. 201–07.10.1016/S0921-5093(03)00065-0 ↗
13. R. Sota: Master’s Thesis, Tokyo Institute of Technology, Tokyo, 2002.
14. J. Cadek: Creep in Metallic Materials, Elsevier, Amsterdam, 1988.
15. M. Regev, O. Botstein, M. Bamberger, and A. Rosen: Mater. Sci. Eng., 2001, vol. A302, pp. 51–55.10.1016/S0921-5093(00)01353-8 ↗
16. S. Kamado, I.A. Anyanwu, Y. Oshima, and Y. Kojima: Proc. 4th Pacific Rim Int. Conf. on Advanced Materials and Processing, The Japan Institute of Metals, Sendai, 2001, pp. 1167–70.
17. O.D. Sherby and P.M. Burke: Progr. Mater. Sci., 1966, vol. 13, pp. 325–90.
18. Y. Terada, N. Ishimatsu, R. Sota, T. Sato, and K. Ohori: Mater. Sci. Forum, 2003, vols. 419–422, pp. 459–64.10.4028/www.scientific.net/MSF.419-422.459 ↗