journal article·2004-10

Dynamic deformation behavior and ballistic impact properties of Ti-6Al-4V alloy having equiaxed and bimodal microstructures

Dong-Geun Lee, You Hwan Lee, Sunghak Lee, Chong Soo Lee, Sun-Moo Hur

Publisher page

Abstract

Effects of microstructural morphology on dynamic deformation behavior and ballistic impact properties of Ti-6Al-4V alloy plates were investigated in this study. Dynamic torsional and ballistic impact tests were conducted on equiaxed and bimodal microstructures, which were processed by different heat treatments, and then the test data were analyzed in relation to microstructures and tensile properties. According to the dynamic torsional test data, maximum shear stress and fracture shear strain of the bimodal microstructure were higher than those of the equiaxed microstructure, and the possibility of the adiabatic shear band formation was more likely in the equiaxed microstructure than in the bimodal microstructure. In the ballistically impacted region of the equiaxed microstructure, a number of adiabatic shear bands and cracks were observed to be formed along plastic flow lines, and delamination occurred because of cracking along the flow lines or shear bands. In the case of the bimodal microstructure, shear bands were found in limited areas near the penetrated surface without occurring delamination, and their number was smaller than that of the equiaxed microstructure. Thus, ballistic performance of the bimodal microstructure was better than that of the equiaxed microstructure, which was consistent with the dynamic torsional test results.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Velocity Impact and Material Behavior · Energetic Materials and Combustion · Structural Response to Dynamic Loads

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. D. Eylon, J.A. Hall, C.M. Pierce, and D.L. Ruckel: Metall. Trans. A, 1976, vol. 7A, pp. 1817–26.10.1007/BF02654976 ↗
2. R. Boyer, G. Welsch, and E.W. Collings: Materials Properties Handbook, Titanium Alloys, ASM International, Materials Park, OH, 1994, pp. 483–636.
3. A. Gysler and G. Lutjering: Metall. Trans. A, 1982, vol. 13A, pp. 1435–43.10.1007/BF02642882 ↗
4. S.L. Semiatin and T.R. Bieler: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 1871–75.10.1007/s11661-001-0166-y ↗
5. B.K. Kad, S.E. Schoenfeld, and M.S. Burkins: Mater. Sci. Eng., 2002, vol. A322, pp. 241–51.10.1016/S0921-5093(01)01135-2 ↗
6. A.L. Wingrove: Metall. Trans. A, 1973, vol. 4A, pp. 1829–33.10.1007/BF02665409 ↗
7. S.P. Timothy and I.M. Hutchings: Acta Metall., 1985, vol. 33, pp. 667–76.10.1016/0001-6160(85)90030-6 ↗
8. D.-G. Lee, S. Lee, C. Lee, and S. Hur: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2541–48.10.1007/s11661-003-0013-4 ↗
9. H.T. Li, Y.M. Zhang, and D.Z. Yang: Mater. Sci. Eng., 2000, vol. A292, pp. 130–32.
10. Q. Xue, M.A. Meyers, and V.F. Nesterenko: Acta Mater., 2002, vol. 50, pp. 575–96.10.1016/S1359-6454(01)00356-1 ↗
11. D.-G. Lee, S. Lee, and C.S. Lee: Mater. Sci. Eng. A, 2004, vol. A366, pp. 25–37.10.1016/j.msea.2003.08.061 ↗
12. M.A. Meyers, G. Subhash, B. Kad, and L. Prasad: Mech. Mater., 1994, vol. 17, pp. 175–93.10.1016/0167-6636(94)90058-2 ↗
13. H.J. Ryu, S.H. Hong, D.-K. Kim, and S. Lee: Met. Mater., 1998, vol. 4, pp. 367–71.10.1007/BF03187793 ↗
14. H.A. Grebe, H.-R. Pak, and M.A. Meyers: Metall. Trans. A, 1985, vol. 16A, pp. 761–75.10.1007/BF02814827 ↗
15. A. Molinari, C. Musquar, and G. Sutter: Int. J. Plasticity, 2002, vol. 18, pp. 443–59.10.1016/S0749-6419(01)00003-1 ↗
16. S.P. Timothy: Acta Metall., 1987, vol. 35, pp. 301–06.10.1016/0001-6160(87)90238-0 ↗
17. A. Marchand and J. Duffy: J. Mech. Phys. Solids, 1988, vol. 36, pp. 251–83.10.1016/0022-5096(88)90012-9 ↗
18. M.A. Meyers and C.L. Wittman: Metall. Trans. A, 1990, vol. 21A, pp. 3153–64.10.1007/BF02647311 ↗
19. M.E. Backman and W. Goldsmith: Int. J. Eng. Sci., 1978, vol. 16, pp. 1–99.10.1016/0020-7225(78)90002-2 ↗
20. M.A. Meyers and H.-R. Pak: Acta Metall., 1986, vol. 34, pp. 2493–99.10.1016/0001-6160(86)90152-5 ↗
21. B.K. Kad, S.E. Schoenfeld, and M.S. Burkins: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 937–47.10.1007/s11661-002-0163-9 ↗
22. D.-G. Lee, S. Kim, S. Lee, and C.S. Lee: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 315–24.10.1007/s11661-001-0263-y ↗
23. D.-G. Lee, S. Lee, C.S. Lee, and S. Hur: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2541–48.10.1007/s11661-003-0013-4 ↗
24. Metals Handbook, 9th ed., ASM, Metals Park, OH, 1990, vol. 8, pp. 218–24.
25. D.-K. Kim, S. Lee, and H.-S. Song: Metall. Mater., 1998, vol. 4, pp. 508–15.
26. C. Zener and J.H. Hollomon: J. Appl. Phys., 1944, vol. 15, pp. 22–32.10.1063/1.1707363 ↗
27. J.W. Hutchinson: Scripta Metall., 1984, vol. 18, pp. 421–22.10.1016/0036-9748(84)90414-9 ↗
28. C.F. Hickey, Jr.: Metallic Materials for Lightweight Applications, Proceeding of the 40th Sagamore Army Materials Research Conference, E.B. Kula and M.G.H. Wells, eds., Plymouth, MA, 1993, pp. 243–53.
29. M.F. Kanninen and C.H. Popelar: Advanced Fracture Mechanics, Oxford University Press, New York, NY, 1985, pp. 273–98.
30. C.L. Wittman, M.A. Meyers, and H.-R. Pak: Metall. Trans. A, 1990, vol. 21A, pp. 707–16.10.1007/BF02671941 ↗
31. Y. Me-Bar and D. Shechtman: Mater. Sci. Eng., 1983, vol. 58, pp. 181–88.10.1016/0025-5416(83)90044-7 ↗
32. M.C. Mataya, M.J. Carr, and G. Krauss: Metall. Trans. A, 1982, vol. 13A, pp. 1263–74.10.1007/BF02645510 ↗
33. M.A. Meyers, Y.B. Xu, Q. Xue, M.T. Perez-Prado, and T.R. McNelley: Acta Mater., 2003, vol. 51, pp. 1307–25.10.1016/S1359-6454(02)00526-8 ↗
34. K. Cho, S. Lee, S.R. Nutt, and J. Duffy: Acta Metall., 1993, vol. 41, pp. 923–32.10.1016/0956-7151(93)90026-O ↗
35. H.J. McQueen: in Hot Deformation of Aluminum Alloys, T.G. Langdon, ed., TMS, Warrendale, PA, 1991, pp. 31–38.
36. P.W. Leech: Metall. Trans. A, 1985, vol. 16A, pp. 1900–03.10.1007/BF02670378 ↗