Preparation and mechanical properties of highly densified nanocrystalline Al
Source abstract
Abstract
The preparation of highly densified nanocrystalline (NC) Al was conducted in three steps. First, the NC Al powder was synthesized by an active H2 plasma evaporation method. Then, the NC Al powder was compacted at room temperature into disk-shaped samples with a 25-mm diameter and 2-mm thickness and was sintered at 620°C or 635°C (sintered NC Al). The sintering does not result in grain growth. Finally, the sintered NC Al was rolled at room temperature into sheet samples with a 1-mm thickness and 99 pct relative density (cold-deformed NC Al). The microhardnesses and tensile properties of the sintered NC Al and cold-deformed NC Al were tested at room temperature. The results show that their strengths are basically the same, and the yield strengths (σ0.2) and tensile strengths ((σb)) are 12 to 16 and 5 to 6 times those of annealed coarse-grained Al, respectively, but the elongation to failure of the cold-deformed NC Al is up to 8 pct, which is 2 times that of the sintered NC Al and higher than that of cold-deformed, coarse-grained Al by 30 pct. The failure features of the sintered NC Al and cold-deformed NC Al belong to typical plastic fracture with ductile dimples, and the mechanism of failure is transgranular shear fracture.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. 4th Int. Conf. on Nanostructural Materials (Nano’98), Book of Abstracts, Stockholm, June 14–19, 1998.
2. R. Birringer, H. Gleiter, H.P. Klein, and P. Marquardt: Phys. Lett., 1984, vol. A102, pp. 365–69.10.1016/0375-9601(84)90300-1 ↗
3. R. Birringer, U. Herr, and H. Gleiter: Trans. Jpn. Inst. Met., 1986, suppl., vol. 27, pp. 43–52.
4. H. Gleiter: Progr. Mater. Sci., 1989, vol. 33, pp. 223–315.10.1016/0079-6425(89)90001-7 ↗
5. H. Hahn, J.A. Eastman, and R.W. Siegel: Cer. Trans., 1988, vol. 1B, pp. 1115–22.
6. R.W. Siegel, S. Ramasamy, H. Hahn, Li Zongquan, Lu Ting, and R. Gronsky: J. Mater. Res., 1988, vol. 3, pp. 1367–72.10.1557/JMR.1988.1367 ↗
7. G.W. Nieman, J.R. Weertman, and R.W. Siegel: J. Mater. Res., 1991, vol. 6, pp. 1012–27.10.1557/JMR.1991.1012 ↗
8. J.R. Weertman: Mater. Sci. Eng., 1993, vol. 166, pp. 161–67.10.1016/0921-5093(93)90319-A ↗
9. P.G. Sanders, G.E. Fougere, L.J. Thompson, J.A. Eastman and J.R. Weertman: Nanostruct. Mater., 1997, vol. 8, pp. 243–52.10.1016/S0965-9773(97)00167-0 ↗
10. P.G. Sanders, J.A. Eastman, and J.R. Weertman: Acta Mater., 1997, vol. 45, pp. 4019–25.10.1016/S1359-6454(97)00092-X ↗
11. L. He and E. Ma: J. Mater. Res., 1996, vol. 11, pp. 72–80.10.1557/JMR.1996.0010 ↗
12. J. Rawers, R. Krabbe, and N. Duttlinger: Mater. Sci. Eng., 1997, vol. A230, pp. 139–45.10.1016/S0921-5093(97)00015-4 ↗
13. G.R. Shaik and W.W. Milligan: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 895–904.10.1007/s11661-997-1018-1 ↗
14. J.E. Carsley, A. Fishar, W.W. Milligan, and E.C. Aifantis: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 2261–71.10.1007/s11661-998-0104-3 ↗
15. T.R. Malow and C.C. Koch: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 2285–95.10.1007/s11661-998-0106-1 ↗
16. R.Z. Valiev, A.V. Korznikov, and R.R. Mulyukov: Mater. Sci. Eng., 1993, vol. A168, pp. 141–48.10.1016/0921-5093(93)90717-S ↗
17. J. Wang, Z. Horita, M. Furukawa, M. Nemoto, N.K. Tsenev, R.Z. Valiev, Y. Ma, and T.G. Langdon: J. Mater. Res., 1993, vol. 8, pp. 2810–18.10.1557/JMR.1993.2810 ↗
18. R.Z. Valiev, E.V. Kozlov, Y.F. Ivanov, J. Lian, A.A. Nazarov, and B. Baudelet: Acta Mater., 1994, vol. 42, pp. 2467–75.10.1016/0956-7151(94)90326-3 ↗
19. J. Wang, Y. Iwahashi, Z. Horita, M. Furukawa, M. Nemoto, R.Z. Valiev, and T.G. Langdon: Acta Mater., 1996, vol. 44, pp. 2973–82.10.1016/1359-6454(95)00395-9 ↗
20. R.Z. Valiev: Mater. Sci. Eng., 1997, vol. A234–A236, pp. 59–66.10.1016/S0921-5093(97)00183-4 ↗
21. I.V. Alexandrov, Y.T. Zhu, T.C. Lowe, R.K. Islamgaliev, and R.Z. Valiev, Metall. Mater. Trans. A, 1998, vol. 29A, pp. 2253–60.10.1007/s11661-998-0103-4 ↗
22. R. Suryanarayanan, C.A. Frey, S.M.L. Sastry, B.E. Waller, S.E. Bates, and W.E. Buhro: J. Mater. Res., 1996, vol. 11, pp. 439–48.10.1557/JMR.1996.0053 ↗
23. P.G. Sanders, C.J. Youngdahl, and J.R. Weertman: Mater. Sci. Eng., 1997, vols. A234–A236, pp. 77–82.10.1016/S0921-5093(97)00185-8 ↗
24. V.Y. Gertman, R. Birringer, R.Z. Valiev, and H. Gleiter: Scripta Metall. Mater., 1994, vol. 30, pp. 229–34.10.1016/0956-716X(94)90045-0 ↗
25. S. Sakai, H. Tanimoto, and H. Mizubayashi: 4th Int. Conf. on Nanostructural Materials (Nano’98), Book of Abstracts, Stockholm, June 14–19, 1998, p. 107.
26. H.F. Zhang, X.J. Wu, L.G. Du, Y.Q. Wang, and Z.Q. Li: 4th Int. Conf. on Nanostructural Materials (Nano’98), Book of Abstracts, Stockholm, June 14–19, 1998, p. 258.
27. E. Bonetti, L. Pasquini, and E. Sampaoles: Nanostruct. Mater., 1997, vol. 9, pp. 611–14.10.1016/S0965-9773(97)00137-2 ↗
28. S.X. McFadden, R.S. Mishra, R.Z. Valiev, A.P. Zhilyaev, and A.K. Mukherjee: Nature, 1999, vol. 32, pp. 684–86.10.1038/19486 ↗
29. J. Eckert, J.C. Holzer, C.C. Ahn, Z. Fu, and W.L. Johnson: Nanostruct. Mater., 1993, vol. 2, pp. 407–13.10.1016/0965-9773(93)90183-C ↗
30. J.C. Sanchez-Lopoz, A. Fernandez, C.F. Conde, C. Morant, and J.M. Sanz: Nanostruct. Mater., 1996, vol. 7, pp. 813–22.10.1016/S0965-9773(96)00053-0 ↗
31. Xiukui Sun, Wenxiu Chen, Jian Xu, Xueshu Fan, Wenduo Wei, Yukun Wu, and Yingguo Peng: Acta Metall. Sinica, 1992, vol. 5A, pp. 402–8 (English edition).
32. X.K. Sun, J. Xu, W.X. Chen, and W.D. Wei: Nanostruct. Mater., 1994, vol. 4, pp. 337–44.10.1016/0965-9773(94)90143-0 ↗
33. G.T. Murray and T.A. Lograsso: Metals Handbook, 10th ed., ASM INTERNATIONAL, Materials Park, OH, 1990, vol. 2, pp. 1100.
34. C.J. Youngdahl, P.G. Sanders, J.A. Eastman, and J.R. Weertman: Scripta Mater., 1997, vol. 37, pp. 809–13.10.1016/S1359-6462(97)00157-7 ↗
35. J.E. Carsley, J. Ning, W.W. Milligan, S.A. Hackney, and E.C. Aifantis: Nanostruct. Mater., 1995, vol. 5, pp. 441–48.10.1016/0965-9773(95)00257-F ↗
36. J.R. Groza and R.J. Dowding: Nanostruct. Mater., 1996, vol. 7, pp. 749–68.10.1016/S0965-9773(96)00046-3 ↗
37. D. Tabor: The Hardness of Metals, Oxford University Press, London, 1952, p. 107.
38. M.C. Shaw: in Mechanical Behavior of Materials, F.A. Mc Clintock and A.S. Argon, eds., Addison-Wesley, Reading, MA, 1966, p. 443.
39. R.Z. Valiev, N.A. Krasilnikov, and N.K. Tsenev: Mater. Sci. Eng., 1991, vol. A137, pp. 35–40.10.1016/0921-5093(91)90316-F ↗
40. M.N. Rittner, J.R. Weertman, J.A. Eastman, K.B. Yoder, and D.S. Stone: Mater. Sci. Eng., 1997, vol. A237, pp. 185–90.10.1016/S0921-5093(97)00129-9 ↗
41. G.T. Gray, T.C. Lowe, C.M. Caday, R.Z. Valiev, and I.V. Aleksandrov: Nanostruct. Mater., 1997, vol. 9, pp. 477–80.10.1016/S0965-9773(97)00104-9 ↗
42. T. Mukai, M. Kawazoe, and K. Higashi: Nanostruct. Mater., 1998, vol. 10, pp. 755–65.10.1016/S0965-9773(98)00113-5 ↗
43. M. Jain and T. Christman: Acta Metall., 1994, vol. 42, pp. 1901–11.10.1016/0956-7151(94)90015-9 ↗
44. R.C. Gifkins: J. Mater. Sci., 1978, vol. 13, pp. 1926–36.10.1007/BF00552899 ↗