journal article·2026-03Open access

The Effect of Carbon and Silicon Variation on the Microstructure and Mechanical Properties of a Cobalt-Based Superalloy

M. E. Pek, J. M. Hogg, P. Jan, G. J. Wise, N. L. Church, D. M. Collins, P. Jackson, H. J. Stone

Abstract

Abstract The performance of cast Co-based superalloys is strongly influenced by the nature, stability, and distribution of carbide phases, which depend on C and Si content. This study examines the effect of C (0.25, 0.5 wt pct) and Si (1, 4 wt pct) on the microstructure and tensile behavior of a cast Co-based superalloy. As-cast microstructures were dominated by M 23 C 6 in low-Si alloys and M 12 C in high-Si alloys, with χ phase formed in the low-C, high-Si alloy. Thermal exposures at 800 °C and 1000 °C (100 h) promoted carbide transformation and intragranular precipitation, whereas 1200 °C (50 h) accelerated transformation and coarsening. At room temperature, high-Si contents increased yield strength but significantly reduced ductility, with crack susceptibility increasing from M 12 C to M 23 C 6 to χ . Embrittlement was exacerbated after 800 °C aging due to needle-like intragranular σ and M 12 C precipitation in high-Si alloys. Furthermore, 1000 °C tensile testing of as-cast alloys revealed a performance inversion: the M 23 C 6 -reinforced low-Si alloy achieved superior strength (UTS ~ 196 MPa) compared to high-Si variants. These findings establish mechanistic links between chemistry, carbide evolution, and tensile response, underscoring the need to limit Si and balancing C to optimize ductility and strength in Co-based superalloys.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High Temperature Alloys and Creep · Additive Manufacturing Materials and Processes · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (50)

Show source-provided references
1. P. Berthod, J.P.K. Gomis, and G. Medjahdi: Metall. Mater. Trans. A, 2020, vol. 51A, pp. 4168–85.10.1007/s11661-020-05828-8 ↗
2. J.R. Davis: in Metals Handbook Desk Edition, ASM International, 1998, pp. 616–20.10.31399/asm.hb.mhde2.9781627081993 ↗
3. A.J. Goodfellow, E.I. Galindo-Nava, K.A. Christofidou, N.G. Jones, T. Martin, P.A.J. Bagot, C.D. Boyer, M.C. Hardy, and H.J. Stone: Metall. Mater. Trans. A, 2018, vol. 49A, pp. 718–28.10.1007/s11661-017-4336-y ↗
4. R.C. Reed: The Superalloys, Cambridge University Press, 2006.10.1017/CBO9780511541285 ↗
5. A.M. Beltran: in Superalloys II, C.T. Sims, N.S. Stoloff, and W.C. Hagel, eds., Wiley-Interscience, New York, 1987, pp. 135–63.
6. J. Di Martino, S. Michon, P. Berthod, C. Rapin, R. Podor, and P. Steinmetz: in Ceramic Transactions, vol. 141, John Wiley & Sons, Ltd, 2006, pp. 241–8.10.1002/9781118405949.ch22 ↗
7. Haynes International: Haynes 188 Alloy. https://haynesintl.com/en/alloys/alloy-portfolio/high-temperature-alloys/haynes-188/?generate-brochure=1&post_id=1912&type=full&_wpnonce=83d195e574 (accessed 1 Dec 2025).
8. J.P. Moffat, N.G. Jones, P. Jackson, and H.J. Stone: J. Alloys Compd., 2023, vol. 936, p. 168251.10.1016/j.jallcom.2022.168251 ↗
9. J.P. Moffat, T.E. Whitfield, K.A. Christofidou, E.J. Pickering, N.G. Jones, and H.J. Stone: Metals (Basel), 2020, vol. 10, p. 248.10.3390/met10020248 ↗
10. M.E. El Dahshan, J. Stringer, and D.P. Whittle: Cobalt, 1974, vol. 4, pp. 86–91.
11. W. Gui, H. Zhang, M. Yang, T. Jin, X. Sun, and Q. Zheng: J. Alloys Compd., 2017, vol. 695, pp. 1271–78.10.1016/j.jallcom.2016.10.256 ↗
12. J.P. Moffat, K.A. Christofidou, M.E. Pek, N.G. Jones, P. Jackson, and H.J. Stone: Metall. Mater. Trans. A, 2024, vol. 55A, pp. 791–802.10.1007/s11661-023-07283-7 ↗
13. T. Narushima, S. Mineta, Y. Kurihara, and K. Ueda: JOM: Miner Metal Mater. Soc., 2013, vol. 65, pp. 489–504.10.1007/s11837-013-0567-6 ↗
14. W. Gui, H. Zhang, M. Yang, T. Jin, X. Sun, and Q. Zheng: J. Alloys Compd., 2017, vol. 728, pp. 145–51.10.1016/j.jallcom.2017.08.287 ↗
15. L. Jiang, X.X. Ye, Z.Q. Wang, C. Yu, J.S. Dong, R.B. Xie, Z.J. Li, L. Yan, T.K. Sham, X.T. Zhou, and A.M. Li: J. Alloys Compd., 2017, vol. 728, pp. 917–26.10.1016/j.jallcom.2017.09.042 ↗
16. G.D. Sandrock, R.L. Ashbrook, and J.C. Freche: Effect of Variations in Silicon and Iron Content on Embrittlement of a Cobalt-Base Alloy (L-605), NASA, Cleveland, 1965.
17. R. Liu, M.X. Yao, P.C. Patnaik, and X. Wu: J. Mater. Eng. Perform., 2005, vol. 14, pp. 634–40.10.1361/105994905X64567 ↗
18. L.E. Ramírez-Vidaurri, M. Castro-Román, M. Herrera-Trejo, C.V. García-López, and E. Almanza-Casas: J. Mater. Process. Technol., 2009, vol. 209, pp. 1681–87.10.1016/j.jmatprotec.2008.04.039 ↗
19. T. Liu, M. Yang, F. Han, and J. Dong: Materials, 2020, https://doi.org/10.3390/MA13040959.10.3390/MA13040959 ↗
20. D. Bowden, Y. Krysiak, L. Palatinus, D. Tsivoulas, S. Plana-Ruiz, E. Sarakinou, U. Kolb, D. Stewart, and M. Preuss: Nat. Commun., 2018, vol. 9, pp. 1–10.10.1038/s41467-018-03875-9 ↗
21. E. Zhao, S. Sun, and Y. Zhang: J. Market. Res., 2021, vol. 14, pp. 3029–42.
22. L.K. Borusevich and Ye.I. Gladyshevskiy: Russian Metall, 1965, vol. 6, pp. 83–87.
23. R.L. Fleischer and R.J. Zabala: Metall. Trans. A, 1990, vol. 21, pp. 2709–15.10.1007/BF02646066 ↗
24. A.I. Taub and R.L. Fleischer: Science (1979), 1989, vol. 243, pp. 616–21.
25. T. Narushima, S. Mineta, S. Namba, T. Yoneda, and K. Ueda: Adv. Mater. Res., 2011. https://doi.org/10.4028/www.scientific.net/AMR.277.51.10.4028/www.scientific.net/AMR.277.51 ↗
26. K. Sugawara, Alfirano, S. Mineta, K. Ueda, and T. Narushima: Metall. Mater. Trans. A, 2015, vol. 46A, pp. 4342–50.10.1007/s11661-015-3008-z ↗
27. K. Song, C. Liu, M. Chen, L. Xie, W. Sun, and F. Wang: Corros. Sci., 2023, vol. 214, p. 111011.10.1016/j.corsci.2023.111011 ↗
28. T. Narushima, S. Mineta, A. Alfirano, and K. Ueda: in Interface Oral Health Science 2011, Springer, Japan, 2012, pp. 72–80.10.1007/978-4-431-54070-0_12 ↗
29. T.F. Chase and A.M. Beltran: in Superalloys 1972 (Second International Symposium), TMS, 1972, pp. 1–23.
30. Kennametal Inc.: StelliteTM 31 Alloy, https://catalogs.kennametal.com/infrastructure/Stellite-31-Alloy/1/# (accessed 1 Dec 2025).
31. C.P. Sullivan, M.J. Donachie, and F.R. Morral: Cobalt-Base Superalloys, Centre d’information du cobalt, Brussels, 1970.
32. I. Arganda-Carreras, V. Kaynig, C. Rueden, K.W. Eliceiri, J. Schindelin, A. Cardona, and H. Sebastian Seung: Bioinformatics, 2017, vol. 33, pp. 2424–26.10.1093/bioinformatics/btx180 ↗
33. I. Arganda-Carreras, C. Rueden, J. Salinas-Colina, J. Schindelin, M. Arzt, A. Cardona, J. Eglinger, M. Hiner, J.-Y. Tinevez, P. Freydiere, E. Meijering, and S. Helfrich: fiji/Trainable_Segmentation: Trainable_Segmentation-3.3.2. Zenodo, 2022. https://doi.org/10.5281/zenodo.584909310.5281/zenodo.5849093 ↗
34. J. Schindelin, I. Arganda-Carreras, E. Frise, V. Kaynig, M. Longair, T. Pietzsch, S. Preibisch, C. Rueden, S. Saalfeld, B. Schmid, J.Y. Tinevez, D.J. White, V. Hartenstein, K. Eliceiri, P. Tomancak, and A. Cardona: Nat. Methods, 2012, vol. 9, pp. 676–82.10.1038/nmeth.2019 ↗
35. International Organization for Standardization: Metallic materials—Tensile testing—Part 1: Method of test at room temperature (ISO Standard No. 6892-1:2019). https://www.iso.org/standard/78322.html (accessed 27 July 2024).
36. D. Yan, C.C. Tasan, and D. Raabe: Acta Mater., 2015, vol. 96, pp. 399–409.10.1016/j.actamat.2015.05.038 ↗
37. International Organization for Standardization: Metallic materials—Tensile testing—Part 2: Method of test at elevated temperature (ISO Standard No. 6892-2:2018). https://www.iso.org/standard/72571.html (accessed 8 June 2025).
38. J.-O. Andersson, T. Helander, L. Höglund, P. Shi, and B. Sundman: Calphad, 2002, vol. 26, pp. 273–312.10.1016/S0364-5916(02)00037-8 ↗
39. Thermo-Calc Software: TCNI8 Ni-based Superalloys Database. https://thermocalc.com/products/databases/nickel-based-alloys/ (accessed 16 Jan 2025).
40. Thermo-Calc Software: SSOL5 General Alloys and Pure Substances Database. https://thermocalc.com/products/databases/general-alloys-and-pure-substances/ (accessed 16 Jan 2025).
41. D.L. Klarstrom: in Heat Treating of Nonferrous Alloys, ASM International, 2016, pp. 625–33.10.31399/asm.hb.v04e.a0006267 ↗
42. Z. Xu, L. Jiang, J. Dong, Z. Li, and X. Zhou: J. Alloys Compd., 2015, vol. 620, pp. 197–203.10.1016/j.jallcom.2014.09.112 ↗
43. S. Mineta, S. Namba, T. Yoneda, K. Ueda, and T. Narushima: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 2129–38.10.1007/s11661-010-0227-1 ↗
44. R. Rosenthal, B.R. Cardoso, I.S. Bott, R.P.R. Paranhos, and E.A. Carvalho: J. Mater. Sci., 2010, vol. 45, pp. 4021–28.10.1007/s10853-010-4480-x ↗
45. J.P. Moffat: PhD Thesis, University of Cambridge, 2020.
46. A. Lall, P. Bowen, and A. Rabiei: Mater Charact, 2022, vol. 184, p. 111614.10.1016/j.matchar.2021.111614 ↗
47. M.F. Ashby: Phil. Mag., 1966, vol. 14, pp. 1157–78.10.1080/14786436608224282 ↗
48. W.H. Jiang, H.R. Guan, and Z.Q. Hu: Mater. Sci. Eng. A, 1999, vol. 271, pp. 101–08.10.1016/S0921-5093(99)00183-5 ↗
49. D.W. Seaver and A.M. Beltran: J. Eng. Gas Turbine Power, 1993, vol. 115, pp. 155–59.10.1115/1.2906670 ↗
50. Haynes International: Haynes® 25 Alloy. https://haynesintl.com/en/alloys/alloy-portfolio/high-temperature-alloys/haynes-25/#principal-features (accessed 13 Dec 2025).