Fracture Resistance and Crack Growth Mechanisms in Functionally Graded Ti–TiB
Source abstract
Abstract
Abstract This paper presents the results of fracture tests and crack path observations for a layered functionally graded material (FGM) consisting of Ti and TiB phases. The composition varied in a nearly linear manner from a TiB-rich layer at the bottom to commercially pure (CP) Ti at the top. Elastic properties of the mixed phase interlayers were measured using nanoindentation testing, demonstrating a linear variation with composition. These results differ significantly from approximations calculated in previous studies using a non-linear rule-of-mixtures approach. Fracture tests were conducted on single edge notch bend [SEN(B)] specimens with the notch aligned orthogonal to the direction of the composition gradient. For this crack orientation, "average" R-curve behavior based on the J-integral was investigated to understand the mechanics of crack growth. The value of J was found to be minimal (less than 1 N/mm) below 47 pct volume fraction of TiB compared to a reported value of approximately 150 N/mm for pure Ti. These results indicate that a steeper transition to high concentrations of the metallic phase is necessary to achieve adequate fracture resistance in this metal/ceramic FGM. Observations on the specimen surface indicate crack path toughening mechanisms of this functionally graded material include crack bridging, branching, and deflection.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Aluminum Alloys Composites Properties · Numerical methods in engineering
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (35)
Show source-provided references
1. M. Niino, T. Hirai, and R. Watanabe: J. Jpn. Soc. Compos. Mater., 1987, vol. 13(6), pp. 257–64.10.6089/jscm.13.257 ↗
2. M. Sasaki, Y. Wang, T. Hirano, and T. Hirai: J. Ceram. Soc. Jpn., 1989, vol. 97(1125), pp. 539–43.10.2109/jcersj.97.539 ↗
3. A. Kawasaki, R. Watanabe, Elsevier Science Pub. Co., Tokyo, Japan, 1987, pp. 1197–1202.10.1007/978-94-009-1373-8_201 ↗
4. T. Fukushima, 1990, pp. 145–150.10.1016/0090-4295(90)80064-T ↗
5. Y. Miyamoto, H. Nakanishi, I. Tanaka, T. Okamoto, O. Yamada, Sendai, 1990, pp. 257–62.
6. N. Sata, N. Sanada, T. Hirano, M. Niino, in: Z.A. Munir, J.B. Holt (Eds.), VCH Publishers, New York, 1990, pp. 195–203.
7. A.P. Tomsia, E. Saiz, H. Ishibashi, M. Diaz, J. Requena, and J.S. Moya: J. Eur. Ceram. Soc., 1998, vol. 18(9), pp. 1365–71.10.1016/S0955-2219(98)00066-1 ↗
8. J. Lambros, M.H. Santare, H. Li, and G.H. Sapna: Exp. Mech., 1999, vol. 39(3), pp. 184–90.10.1007/BF02323551 ↗
9. D.R. Feenstra, R. Banerjee, H.L. Fraser, A. Huang, A. Molotnikov, and N. Birbilis: Curr. Opin. Solid State Mater. Sci., 2021, vol. 25(4), p. 100924.10.1016/j.cossms.2021.100924 ↗
10. A. Reichardt, A.A. Shapiro, R. Otis, R.P. Dillon, J.P. Borgonia, B.W. McEnerney, P. Hosemann, and A.M. Beese: Int. Mater. Rev., 2021, vol. 66(1), pp. 1–29.10.1080/09506608.2019.1709354 ↗
11. Y. Li, Z.Y. Feng, L. Hao, L.J. Huang, C.X. Xin, Y.S. Wang, E. Bilotti, K. Essa, H. Zhang, Z. Li, F.F. Yan, and T. Peijs: Adv. Mater. Technol., 2020, vol. 5(6), p. 1900981.10.1002/admt.201900981 ↗
12. C. Zhang, F. Chen, Z.F. Huang, M.Y. Jia, G.Y. Chen, Y.Q. Ye, Y.J. Lin, W. Liu, B.Q. Chen, Q. Shen, L.M. Zhang, and E.J. Lavemia: Mater. Sci. Eng. A, 2019, vol. 764, p. 138209.10.1016/j.msea.2019.138209 ↗
13. C.J. Han, Y. Li, Q. Wang, D.S. Cai, Q.S. Wei, L. Yang, S.F. Wen, J. Liu, and Y.S. Shi: Mater. Design, 2018, vol. 141, pp. 256–66.10.1016/j.matdes.2017.12.037 ↗
14. M.R. Hill, R.D. Carpenter, G.H. Paulino, Z.A. Munir, and J.C. Gibeling: Am. Soc. Test. Mater., 2002, vol. 1409, pp. 169–84.
15. Z.-H. Jin and R.C. Batra: Int. J. Eng. Sci., 1996, vol. 34(15), pp. 1705–16.10.1016/S0020-7225(96)00055-9 ↗
16. Z.-H. Jin and R.C. Batra: Mater. Sci. Eng. A, 1998, vol. 242(1–2), pp. 70–76.10.1016/S0921-5093(97)00513-3 ↗
17. D.J. Shim, G.H. Paulino, and R.H. Dodds: Int. J. Fracture., 2006, vol. 139(1), pp. 91–117.10.1007/s10704-006-0024-4 ↗
18. D.P. Miller, J.J. Lannutti, and R.D. Noebe: J. Mater. Res., 1993, vol. 8(8), pp. 2004–13.10.1557/JMR.1993.2004 ↗
19. R.D. Carpenter, G.H. Paulino, Z.A. Munir, and J.C. Gibeling: Scripta Mater., 2000, vol. 43(6), pp. 547–52.10.1016/S1359-6462(00)00433-4 ↗
20. W.A. Gooch, B.H.C. Chen, M.S. Burkins, R. Palicka, J. Rubin, and R. Ravichandran: Mater. Sci. Forum, 1999, vol. 308, pp. 614–21.10.4028/www.scientific.net/MSF.308-311.614 ↗
21. S.S. Sahay, K.S. Ravichandran, R. Atri, B. Chen, and J. Rubin: J. Mater. Res., 1999, vol. 14(11), pp. 4214–23.10.1557/JMR.1999.0571 ↗
22. K.B. Panda and K.S.R. Chandran: Metall. Mater. Trans. A, 2003, vol. 34A(9), pp. 1993–2003.10.1007/s11661-003-0164-3 ↗
23. J.P. Quast, C.J. Boehlert, R. Gardner, E. Tuegel, and T. Wyen: Mater. Sci. Eng. A, 2008, vol. 497(1–2), pp. 1–9.10.1016/j.msea.2008.07.045 ↗
24. H.T. Tsang, C.G. Chao, and C.Y. Ma: Scripta Mater., 1997, vol. 37(9), pp. 1359–65.10.1016/S1359-6462(97)00251-0 ↗
25. R.D. Carpenter, W.W. Liang, G.H. Paulino, J.C. Gibeling, and Z.A. Munir: Mater. Sci. Forum, 1999, vol. 308–311, pp. 837–42.10.4028/www.scientific.net/MSF.308-311.837 ↗
26. Z.-H. Jin, G.H. Paulino, and R.H. Dodds: Eng. Fract. Mech., 2003, vol. 70(14), pp. 1885–1912.10.1016/S0013-7944(03)00130-9 ↗
27. G. Cao, L. Geng, and M. Naka: J. Am. Ceram. Soc., 2006, vol. 89(12), pp. 3836–38.10.1111/j.1551-2916.2006.01280.x ↗
28. G. Constantinides, K.S. Ravi Chandran, F.-J. Ulm, and K.J. Van Vliet: Mater. Sci. Eng. A, 2006, vol. 430(12), pp. 189–202.10.1016/j.msea.2006.05.125 ↗
29. W.C. Oliver and G.M. Pharr: J. Mater. Res., 1992, vol. 7(6), pp. 1564–83.10.1557/JMR.1992.1564 ↗
30. Z.H. Jin and R.H. Dodds Jr.: Eng. Fract. Mech., 2004, vol. 71(12), pp. 1651–72.10.1016/j.engfracmech.2003.08.002 ↗
31. R.R. Atri, K.S. Ravichandran, and S.K. Jha: Mater. Sci. Eng. A, 1999, vol. 271(1–2), pp. 150–59.10.1016/S0921-5093(99)00198-7 ↗
32. G.H. Paulino, Z.-H. Jin, and R.H. Dodds: Compr. Struct. Integr., 2003, vol. 2, pp. 607–44.10.1016/B0-08-043749-4/02101-7 ↗
33. Z.-H. Jin and R.C. Batra: J. Mech. Phys. Solids, 1996, vol. 44(8), pp. 1221–35.10.1016/0022-5096(96)00041-5 ↗
34. G.H. Paulino, R.D. Carpenter, W.W. Liang, Z.A. Munir, and J.C. Gibeling: Eng. Fract. Mech., 2001, vol. 68(12), pp. 1417–32.10.1016/S0013-7944(01)00018-2 ↗
35. K.S. Ravichandran: Mater. Sci. Eng. A, 1995, vol. 201(1–2), pp. 269–76.10.1016/0921-5093(95)09773-2 ↗