journal article·2021-11

Solidification Microstructure of Aluminum AA 6016-T4 Resistance Spot Welds Using a Short-Pulse Technique

Eric W. Schulz, Matthias Wagner, Holger Schubert, Wenqi Zhang, Bharat Balasubramanian, Luke N. Brewer

Publisher page

Abstract

The influence of the duration of the current pulse on the solidification microstructure of resistance spot welded (RSW) samples of aluminum alloy 6016-T4 with the short-pulse technique was investigated through experiments and numerical modeling. Microstructure was analyzed in terms of morphology and size, and primary and secondary dendrite arm spacing were measured on experimental samples. A reduction in pulse width resulted in a fine, columnar-dendritic microstructure in the outer regions of the fusion zone as well as a larger equiaxed-dendritic zone in the fusion zone center. A two-dimensional, axisymmetric finite element model of the spot welding process with new methods for calculation of the solidification parameters G (thermal gradient in the solid behind the solid–liquid interface) and R (velocity of the solid–liquid interface) was used for investigation of influence of pulse time on solidification microstructure and comparison to experimental results. Morphological trends in the solidification structure showed good agreement between experiments and simulations, and the influence of the pulse duration on the solidification parameters evolved because of changing heat transfer conditions. Simulated solidification data suggest that the solidification of aluminum during RSW falls in the regime of rapid solidification.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. S.M. Manladan, F. Yusof, S. Ramesh, M. Fadzil, Z. Luo, and S. Ao: Int. J. Adv. Des. Manuf. Technol., 2017, vol. 90, pp. 605–34. .10.1007/s00170-016-9225-9 ↗
2. D.C. Saha and Y. Park: J. KWJS., 2011, vol. 29, pp. 35–40. .
3. J.E. Gould: Weld. J. (Miami, FL, U.S.)., 2012, vol. 91, pp. 23–34. .
4. A. Ambroziak and M. Korzeniowski: Archives of Civil and Mechanical Engineering., 2010, vol. 10, pp. 5–13. .
5. German Institute for Standardization: ISO 10447:2015-05, DIN Deutsches Institut für Normung e. V., Berlin, Germany, 2015.
6. D. Afshari, M. Sedighi, Z. Barsoum, and R.L. Peng: Proc. Inst. Mech. Eng. Part B., 2012, vol. 226, pp. 1026–32. .10.1177/0954405411435198 ↗
7. W. Zhang, D. Sun, L. Han, and D. Liu: Mater. Des., 2014, vol. 57, pp. 186–94. .10.1016/j.matdes.2013.12.045 ↗
8. Y. Li, F.Y. Yan, Z. Luo, Y.J. Chao, S.S. Ao, and X.T. Cui: Proc. Inst. Mech. Eng., Part B., 2015, vol. 24, pp. 2546–55. .
9. H. Zhang and J. Senkara: Resistance Welding: Fundamentals and Applications. 2nd ed. CRC Press, Boca Raton, FL, 2012, pp. 1–58.
10. S. Kou: Welding Metallurgy. 2nd ed. Wiley, Hoboken, NJ, 2003, pp. 145–69.
11. W. Kurz and R. Trivedi: Mater. Sci. Eng. A., 1994, vol. 179, pp. 46–51. .10.1016/0921-5093(94)90162-7 ↗
12. A. Farzadi, S. Serajzadeh, and A.H. Kokabi: Int. J. Therm. Sci., 2010, vol. 49, pp. 809–19. .10.1016/j.ijthermalsci.2009.11.007 ↗
13. Z. Xue, S. Hu, D. Zuo, and J. Shen: Trans. Tianjin Univ., 2014, vol. 20, pp. 315–21. .10.1007/s12209-014-2245-3 ↗
14. J.E. Gould: Weld. J. (Miami, FL, U.S.), 1994, vol. 73, pp. 67s-72s.
15. J.E. Gould: Weld. J. (Miami, FL, U.S.), 1994, vol. 73, pp. 91s-100s.
16. E.W. Schulz, M. Wagner, H. Schubert, W. Zhang, B. Balasubramanian and L.N. Brewer: Weld. J. (Miami, FL, U.S.), 2021, vol. 100, pp. 41s-51s.10.29391/2021.100.004 ↗
17. E.W. Schulz, M. Wagner, H. Schubert, W. Zhang, B. Balasubramanian and L.N. Brewer: Weld. J. (Miami, FL, U.S.), 2021, vol. 100, pp. 83s-92s.
18. Automobile Industry Association: VDA 239-200, Verband der Automobilindustrie e.V., Berlin, Germany, 2013.
19. SWANTEC Software and Engineering: Sorpas 2D Version 13 User Manual, SWANTEC Software and Engineering ApS, Lyngby, Denmark, 2018.
20. W. Zhang: SAE Trans., 2003, vol. 112, pp. 556–64. .
21. W. Kurz and D.J. Fisher: Acta Metall., 1981, vol. 29, pp. 11–20. .10.1016/0001-6160(81)90082-1 ↗
22. M. Gündüz and J.D. Hunt: Acta Metall., 1985, vol. 33, pp. 1651–72. .10.1016/0001-6160(85)90161-0 ↗
23. P.A. Dias Jácome, N. Von Paraski, A. Furtado Ferreira, A. Garcia and I. Leão Ferreira: 7th Brazilian Congress on Manufacturing Engineering, unpublished research, 2013.
24. R. Trivedi and W. Kurz: Acta Metall., 1994, vol. 42, pp. 15–23. .10.1016/0956-7151(94)90044-2 ↗