Mechanistic Modeling of Cyclic Softening in Ni-Based Superalloys at Elevated Temperatures
Source abstract
Abstract
The cyclic stress–strain response of Ni-based superalloys at elevated temperatures in the literature has been analyzed and modeled mechanistically to develop a better understanding of cyclic softening behavior as a function of temperatures. The analysis reveals that at temperatures below 973 K, cyclic softening in Ni-based superalloys is caused predominantly by shearing of γ′ precipitates. The strain hardening exponent (n1) is positive at lower fatigue cycles, but the strain-hardening exponent (n2) becomes negative (i.e., strain softening) at higher fatigue cycles. The onset of cyclic softening appears to correspond to shearing of γ′ precipitates into two halves. In contrast, cyclic softening at temperatures above 1173 K is partly caused by thermal recovery of anomalous hardening induced by cross slip of super-dislocations from {111} planes to {001} planes in the presence of climb-assisted bowing of dislocations around γ′ precipitates, and partly caused by a reduction of forest dislocation density at the γ/γ′ interface due to impinging super-dislocations. As the result of these mechanism changes, the onset of cyclic softening commences after the first fatigue cycle but continues at a slow rate at a temperature at 1173 K or above. Relations of the strain-hardening exponents on microstructural variables have been developed and validated against experimental data from the literature.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (49)
Show source-provided references
1. P.A. Flinn: Strengthening Mechanisms in Solids, ASM, Metals Park, OH, 1962.
2. R.G. Davies and N.S. Stoloff: Trans. TMS-AIME, 1965, vol. 233, pp. 714–19.
3. Y. Mishima, S. Ochiai, N. Hamao, M. Yodogawa, and T. Suzuki: Trans. Jpn. Inst. Met., 1986, vol. 27, pp. 648–55.10.2320/matertrans1960.27.648 ↗
4. S.M. Copley and B.H. Kear: Trans. TMS-AIME, 1967, vol. 239, pp. 977–84.
5. G.R. Leverant, M. Gell, and S.W. Hopkins: Mater. Sci Eng., 1971, vol. 8, pp. 125–33.10.1016/0025-5416(71)90050-4 ↗
6. D.M. Shah and D.N. Duhl: in Superalloys 1984, Proc. 5th Intl. Symposium on Superalloys, M. Gell, C. S. Kortovich, and R. C. Voigt, Eds., AIME, Warrendale Pa., 1984, pp. 105–14.10.7449/1984/Superalloys_1984_105_114 ↗
7. B.H. Kear and H.G.F. Wilsdorf: Trans. Metall. Soc. AIME, 1962, vol. 224, pp. 382–86.
8. D. Caillard and V. Paidar: Acta Mater., 1996, vol. 44(7), pp. 2759–71.10.1016/1359-6454(95)00388-6 ↗
9. M. Gell and G.R. Leverant: in Mechanisms of high temperature fatigue. ASTM STP., 1973, vol. 520, pp. 37–67.
10. R.W. Kozar, A. Suzuki, W.W. Milligan, J.J. Schirra, M.F. Savage, and T.M. Pollock: Metall. Mater. Trans. A, 2009, vol. 40A(7), pp. 1588–1603. https://doi.org/10.1007/s11661-009-9858-5.10.1007/s11661-009-9858-5 ↗
11. W. Huther and B. Reppich: Z. Metallkd., 1978, vol. 69, pp. 628–34.
12. H. Gleiter and E. Hornbogen: Mater. Sci. Eng., 1968, vol. 2, pp. 285–302.10.1016/0025-5416(68)90047-5 ↗
13. L.M. Brown and R.K. Ham: in Strengthening Methods in Crystals, in Elsevier. A. Kelly and R.B. Nicholson, eds., Oxford, 1971, pp. 9–135.
14. T.A. Parthasarathy, S.I. Rao, and D.M. Dimiduk: Superalloys,: TMS (The Minerals, Metals & Materials Society). Warrendale, PA, 2004, vol. 2004, pp. 887–96.
15. L. Tabourot, M. Fivel, and E. Rauch: Mater. Sci. Eng. A, 1997, vol. 234–236, pp. 639–42.10.1016/S0921-5093(97)00353-5 ↗
16. K.S. Chan: Metall. Mater. Trans. A, 2018, vol. 49A, pp. 5353–67.10.1007/s11661-018-4878-7 ↗
17. E. Galindo-Nava, L. Connor, and C. Rae: Acta Mater., 2015, vol. 98, pp. 377–90.10.1016/j.actamat.2015.07.048 ↗
18. W. Ramberg and W.R. Osgood: Technical Note 503: Determination of Stress–strain Curves by Three Parameters, National Advisory Committee on Aeronautics (NACA), 1941.
19. K. Gopinath, A.K. Gogia, S.V. Kamat, B. Balamuralikrishnan, and U. Ramamurty: Metall. Mater. Trans. A, 2008, vol. 39A(10), pp. 2340–50.10.1007/s11661-008-9585-3 ↗
20. K.S. Chan: Metall. Mater. Trans. A, 2020, vol. 51A, pp. 5653–66.10.1007/s11661-020-05965-0 ↗
21. K.S. Chan: Metall. Mater. Trans. A, 2021, vol. 52A, pp. 1759–76.10.1007/s11661-021-06187-8 ↗
22. P. Zhang, Q. Zhu, G. Chen, H. Qin, and C. Wang: Mater. Trans., 2016, vol. 57(1), pp. 25–32.10.2320/matertrans.M2015316 ↗
23. K. Gopinath, A.K. Gogia, S.V. Kamat, B. Balamuralikrishnan, and U. Ramamurty: Acta Mater., 2009, vol. 57, pp. 3450–59.10.1016/j.actamat.2009.03.046 ↗
24. B.A. Lerch, N. Jayaraman, and S.D. Antolovich: Mater. Sci. Eng., 1984, vol. 66, pp. 151–66.10.1016/0025-5416(84)90177-0 ↗
25. M. Petrenec, K. Obrtlik, and J. Polak: Key Eng. Mater., 2022, vol. 348–349, pp. 101–04.
26. M. Petrenec, K. Obrtlik, J. Polak, and T. Kruml: Mater. In Tech., 2005, vol. 40(5), pp. 175–78.
27. I. Šulák, K. Obrtlík, and L. Čelko: Met. Mater., 2016, vol. 54(6), pp. 471–81.
28. Z. Chu, J. Yu, X. Sun, H. Guan, and Z. Hu: Mater. Sci. Eng. A, 2008, vol. 488, pp. 389–97.10.1016/j.msea.2007.11.045 ↗
29. K. Obrtlik, P. Lukas, and J. Polak: Low Cycle Fatigue and Elasto-Plastic Behavior of Materials, edited by K-T. Rie and P. D. Portella, Elsevier, New York, 1998, pp. 33–38.
30. P. Li, Q.Q. Li, T. Jin, Y.Z. Zhou, J.G. Li, X.F. Sun, and Z.F. Zhang: Int. J. Fatigue, 2014, vol. 63, pp. 137–44.10.1016/j.ijfatigue.2014.01.018 ↗
31. D. Shi, J. Huang, X. Yang, and H. Yu: Int. J. Fatigue, 2013, vol. 2013, pp. 31–39.10.1016/j.ijfatigue.2012.12.005 ↗
32. L. Zhang, L.G. Zhao, A. Roy, V.V. Silberschmidt, and G. McColvin: Mater. Sci. Eng. A, 2019, vol. 742, pp. 538–47.10.1016/j.msea.2018.12.084 ↗
33. L. Zhang, L.G. Zhao, A. Roy, V.V. Silberschmidt, and G. McColvin: Mater. Sci. Eng. A, 2019, vol. 742, pp. 564–72.10.1016/j.msea.2018.11.040 ↗
34. J. Yu, X. Sun, T. Jin, N. Zhao, H. Guan, and Z. Hu: Mater. Sci. Eng. A, 2010, vol. 527, pp. 2379–89.10.1016/j.msea.2010.01.001 ↗
35. Tool & Die Steels: www.tool-die-steels.com
36. S.G. Sundara Raman and K.A. Padmanabhan: Fatigue, 1994, vol. 16, pp. 209–15.10.1016/0142-1123(94)90005-1 ↗
37. V. Singh, M. Sundararaman, W. Chen, and R.P. Wahi: Metall. Trans. A, 1991, vol. 22A, pp. 499–506.10.1007/BF02656817 ↗
38. M. Sundararaman, W. Chen, V. Singh, and R.P. Wahi: Acta Metal. Mater., 1990, vol. 38, pp. 1813–22.10.1016/0956-7151(90)90293-P ↗
39. K.S. Chan: J. Eng. Mater. Perform., 2020, vol. 29(3), pp. 2035–45. https://doi.org/10.1007/s11665-020-04678-0.10.1007/s11665-020-04678-0 ↗
40. L. M. Brown: in Fatigue and Creep of Composite Materials, Proc. of the 3rd Risø Inter. Symp. on Metall. and Mater. Sci., edited by H. Lilholt and R. Talreja, Risø National Laboratory, Roskilde, Denmark, 1982, pp. 1–8.
41. R. Lagneborg: Scripta Metall., 1975, vol. 7, pp. 605–14.10.1016/0036-9748(73)90222-6 ↗
42. Y. Ru, S. Li, J. Zhao, Y. Pei, H. Wang, S. Gong, and H. Xu: Sci. Rep., 2020, https://doi.org/10.1038/srep29941.10.1038/srep29941 ↗
43. W.M. Lomer: Philos. Mag., 1951, vol. 42, pp. 1327–31.10.1080/14786444108561389 ↗
44. A.H. Cottrell: Dislocation and Plastic Flow in Crystals, Oxford University, Oxford, 1953.
45. H.S. Chen, J.J. Gilman, and A.K. Head: J. Appl. Lett., 1964, vol. 35, p. 2502.
46. M. Petrence, K. Obrtlik, and J. Polak: Mater. Sci. Eng. A, 2005, vol. 400–401, pp. 485–88.10.1016/j.msea.2005.01.058 ↗
47. C. Stocker, M. Zimmermann, and H.-J. Christ: Int. J. Fatigue, 2011, vol. 33, pp. 2–9.10.1016/j.ijfatigue.2010.04.008 ↗
48. H. Yang, Z. Li, and M. Huang: Comp. Mater. Sci., 2013, vol. 75, pp. 52–59.10.1016/j.commatsci.2013.02.026 ↗
49. T. Tinga, W.A.M. Brekelmans, and M.G.D. Geers: Model. Simul. Mater. Sci. Eng., 2010, vol. 18, 015005.10.1088/0965-0393/18/1/015005 ↗