journal article·2022-08Open access

Effect of Niobium Supersaturation in Austenite on the Static Recrystallization Behavior of Carbon Structural Steels

B. Rakshe, J. Patel, E. J. Palmiere

Abstract

Abstract This work describes the effect of Nb supersaturation in austenite on the suppression of static recrystallization of austenite during an isothermal holding period following hot deformation. The investigation involved three carbon structural steels with varying Nb concentration at constant C (0.20 pct) and N (0.007 pct) levels. The isothermal double-hit deformation technique led to the determination of T 5 pct and T 95 pct (recrystallization-stop and full recrystallization temperatures, respectively) as a function of a true strain and interpass time. The results indicate that the T 5 pct increases with increasing Nb supersaturation in austenite at a rate of 40 °C per 0.006 pct Nb supersaturation for a true stain ε=0.40. At each respective T 5 pct, all tested steels exhibited an Nb supersaturation ratio ≥ 7.5 in austenite. A high, localized strain-induced precipitation of Nb(CN) was observed at the austenite subgrain boundaries in the unrecrystallized microstructure. This translated into higher values for local precipitate-pinning forces (F PIN), which were significantly higher than that predicted from equilibrium thermodynamics. The critical FPIN for retardation of static recrystallization was found to be 1.6 MPa at the respective T 5 pct for each steel. The present study has contributed to advancing our knowledge of the interplay between Nb solute supersaturation and volume fraction of Nb(CN) precipitation in particular for carbon structural steels. It has also highlighted an opportunity to apply niobium, even an ultra-low addition (i.e., < 100 ppm) to commodity-grade structural steels to reduce overall alloying costs.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. S. Hansen, J. Sande, and M. Cohen: Metall. Trans. A, 1980, vol. 11A, pp. 387–402.10.1007/BF02654563 ↗
2. J. Speer and S. Hansen: Metall. Trans. A, 1989, vol. 20A, pp. 25–38.10.1007/BF02647491 ↗
3. O. Kwon and A. DeArdo: Acta Metall. Mater., 1991, vol. 39(4), pp. 529–38.10.1016/0956-7151(91)90121-G ↗
4. E. Palmiere, C. Garcia, and A. DeArdo: Metall. Mater. Trans. A, 1996, vol. 27(4), pp. 951–60.10.1007/BF02649763 ↗
5. A. le Bon, J. Rofes-Vernis, and C. Rossard: Met. Sci., 1975, vol. 9(1), pp. 36–40.10.1179/030634575790444919 ↗
6. H. Zurob, Y. Brechet, and G. Purdy: Acta Mater., 2001, vol. 49(20), pp. 4183–90.10.1016/S1359-6454(01)00315-9 ↗
7. J. Takahashi, K. Kawakami, J. Hamada, and K. Kimura: Acta Mater., 2016, vol. 107, pp. 415–22.10.1016/j.actamat.2016.01.070 ↗
8. M. Suehiro: ISIJ Int., 1998, vol. 38(6), pp. 547–52.10.2355/isijinternational.38.547 ↗
9. World Steel Association: Steel Consumption in Buildings and infrastructure
10. Stronger Steels in the Built Environment (STROBE), RFSR CT 2016-743504, Final Report
11. B. Donnay and H. Grober: In Conf. Proc. Niobium, Science & Technology. Bridgeville, Pa: Niobium 2001 Limited, 2002.
12. S. Jansto, L. Silvestre and H. Wang: In Conf. Proc. HSLA Steels 2015, Microalloying 2015 & Offshore Engineering Steels 2015, pp. 895–90110.1002/9781119223399.ch112 ↗
13. S. Jansto: Metall. and Mater. Trans. B., 2013, vol. 45(2), pp. 438–44.10.1007/s11663-013-9837-5 ↗
14. S. Jansto: In Conf. Proc. Value Added Niobium Microalloyed Construction Steel, 2012.
15. M. Gómez, S. Medina, A. Quispe, and P. Valles: ISIJ Int., 2002, vol. 42(4), pp. 423–31.10.2355/isijinternational.42.423 ↗
16. Z. Cui, J. Patel and E. Palmiere: In Conf. Proc. HSLA Steels 2015, Microalloying 2015 & Offshore Engineering Steels 2015, pp. 281–87.10.1002/9781119223399.ch30 ↗
17. K. Irvine, F. Pickering, and T. Gladman: Iron Steel Inst J., 1967, vol. 205, pp. 161–82.
18. M. Mirza and C. Sellars: Mater. Sci. Technol., 2001, vol. 17(9), pp. 1133–41.10.1179/026708301101511068 ↗
19. B. Rakshe: PhD thesis, University of Sheffield, UK.
20. R. Thackray, E. Palmiere, and O. Khalid: Materials, 2020, vol. 13(15), pp. 3296–3305.10.3390/ma13153296 ↗
21. R. Higginson and C. Sellars: Worked Examples in Quantitative Metallography, The Institute of Materials, London, 2003, pp. 80–100.
22. M. Ashby and R. Ebeling: Trans. Metall. Soc. AIME, 1966, vol. 236, pp. 1396–1405.
23. M. Loveday, E. Palmiere, C. Sellars, and M. Winden: Mater. High Temp., 2006, vol. 23(2), pp. 85–118.10.1179/mht.2006.006 ↗
24. S. Davenport, N. Silk, C. Sparks, and C. Sellars: Mater. Sci. Technol., 2000, vol. 16, pp. 539–46.10.1179/026708300101508045 ↗
25. O. Kwon and A. DeArdo: Acta Metall. Mater., 1990, vol. 38(1), pp. 41–54.10.1016/0956-7151(90)90133-2 ↗
26. R. Petkovic, M. Luton, and J. Jonas: Can. Metall. Q., 1975, vol. 14(2), pp. 137–45.10.1179/000844375795050201 ↗
27. B. Dutta and E. Palmiere: Metall. Mater. Trans. A., 2003, vol. 34A(6), pp. 1237–47.10.1007/s11661-003-0234-6 ↗
28. B. Dutta, E. Palmiere, and C. Sellars: Acta Mater., 2001, vol. 49(5), pp. 785–94.10.1016/S1359-6454(00)00389-X ↗
29. A. Davenport, R. Miner and R. Kot: In Conf. Proc. Hot Deformation of Austenite Ed. J.B. Balance. A.I.M.E., Warrendale, 1986, pp.
30. T. Gladman: The Physical Metallurgy of Microalloyed Steels, Institute of Materials, London, 1997, pp. 97–99.
31. E. Valdes and C. Sellars: Mater. Sci. Technol., 1991, vol. 7(7), pp. 622–30.10.1179/mst.1991.7.7.622 ↗
32. L. Cuddy: In Conf. Proc. Recrystallisation and Grain Growth of Multiphase and Particles Containing Materials. 1980, pp. 317–30.
33. L. Cuddy: In Conf. Proc. Thermomechanical Processing of Microalloyed Austenite, TMS-AIME, New York, 1982, pp. 289–95.
34. H. Nordberg and B. Aronson: J. Iron Steel Inst., 1968, vol. 206, pp. 1263–66.
35. R. Cahn: In Conf. Proc. Recrystallisation, Grain Growth and Textures (ed. H. Margulin), ASM Publication, 1966, pp. 99–127.
36. P. Beck and P. Sperry: JOM, 1949, vol. 1(3), pp. 240–41.10.1007/BF03398104 ↗
37. P. Beck and P. Sperry: J. Appl. Phys., 1950, vol. 21(2), pp. 150–52.10.1063/1.1699614 ↗
38. J. Bailey and P. Hirsch: In Conf. Proc. Mathematical and Physical Sciences—Series A, Royal Society of London, 1962, 267(1328), pp. 11–30.10.1098/rspa.1962.0080 ↗
39. S. Vervynckt, K. Verbeken, P. Thibaux, and Y. Houbaert: Mater. Sci. Eng. A, 2011, vol. 528, pp. 5519–28.10.1016/j.msea.2011.03.087 ↗
40. A. Kelly, G. Groves, and P. Kidd: In Crystallography and Crystal Defects, Wiley, New York, 2000, pp. 198–99.
41. R. Abbaschian, L. Abbaschian, and R. Reed-Hill: In Physical Metallurgy Principles, Cengage Learning, USA, 2009, pp. 133–38.