journal article·2021-08Open access

Texture-Based Optimization of Crystal Plasticity Parameters: Application to Zinc and Its Alloy

Karol Frydrych, Anna Jarzębska, Saketh Virupakshi, Katarzyna Kowalczyk-Gajewska, Magdalena Bieda, Robert Chulist, Monika Skorupska, Norbert Schell, Krzysztof Sztwiertnia

Abstract

Abstract Evolutionary algorithms have become an extensively used tool for identification of crystal plasticity parameters of hexagonal close packed metals and alloys. However, the fitness functions were usually built using the experimentally measured stress–strain curves. Here, the fitness function is built by means of numerical comparison of the simulated and experimental textures. Namely, the normalized texture difference index is minimized. The evolutionary algorithm with the newly developed fitness function is tested by performing crystal plasticity parameter optimization for both pure zinc and zinc-magnesium alloy. These materials are promising candidates for bioabsorbable implants due to good biocompatibility and optimal corrosion rate. Although their mechanical properties in the as-cast state do not fulfill the requirements, they can be increased by means of hydrostatic extrusion. The developed modeling approach enabled acquisition of the crystal plasticity parameters and analysis of the active deformation mechanisms in zinc and zinc-magnesium alloy subjected to hydrostatic extrusion. It was shown that although slip systems are the main deformation carrier, compressive twinning plays an important role in texture evolution. However, the texture is also partially affected by dynamic recrystallization which is not considered within the developed framework.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Titanium Alloys Microstructure and Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. K. Kowalczyk-Gajewska, K. Sztwiertnia, J. Kawałko, K. Wierzbanowski, K. Wronski, K. Frydrych, S. Stupkiewicz, H. Petryk, Texture evolution in titanium on complex deformation paths: Experiment and modelling. Mater. Sci. Eng. A 637, 251–263 (2015). https://doi.org/10.1016/j.msea.2015.04.04010.1016/j.msea.2015.04.040 ↗
2. K. Frydrych, K. Kowalczyk-Gajewska, Microstructure evolution in cold-rolled pure titanium: Modeling by the three-scale crystal plasticity approach accounting for twinning. Metall. Mater. Trans. A 49(8), 3610–3623 (2018). https://doi.org/10.1007/s11661-018-4676-210.1007/s11661-018-4676-2 ↗
3. K. Frydrych, M. Maj, L. Urbański, K. Kowalczyk-Gajewska, Twinning-induced anisotropy of mechanical response of AZ31B extruded rods. Mater. Sci. Eng. A 771(138610), 1–14 (2020). https://doi.org/10.1016/j.msea.2019.13861010.1016/j.msea.2019.138610 ↗
4. K. Frydrych, K. Kowalczyk-Gajewska, T. Libura, Z. Kowalewski, M. Maj, On the role of slip, twinning and detwinning in magnesium alloy AZ31b sheet. Mater. Sci. Eng. A. (2021). https://doi.org/10.1016/j.msea.2021.141152.10.1016/j.msea.2021.141152 ↗
5. K. Frydrych, Texture evolution of magnesium alloy AZ31B subjected to severe plastic deformation. Eng. Trans. (In review).
6. J. Singh, S. Mahesh, G. Kumar, P. Pant, D. Srivastava, G. Dey, N. Saibaba, I. Samajdar, Deformation twinning in zirconium: direct experimental observations and polycrystal plasticity predictions. Metall. Mater. Trans. A 46(11), 5058–5071 (2015)10.1007/s11661-015-3085-z ↗
7. Q. Wang, C. Cochrane, T. Skippon, Z. Wang, H. Abdolvand, M.R. Daymond, Orientation-dependent irradiation hardening in pure Zr studied by nanoindentation, electron microscopies, and crystal plasticity finite element modeling. Int. J. Plast. 124, 133–154 (2019)10.1016/j.ijplas.2019.08.007 ↗
8. P. Bowen, J. Drelich, J. Goldman, Zinc exhibits ideal physiological corrosion behavior for bioabsorbable stents. Advanced materials 25(18), 2577–2582 (2013)10.1002/adma.201300226 ↗
9. W. Pachla, S. Przybysz, A. Jarzębska, M. Bieda, K. Sztwiertnia, M. Kulczyk, J. Skiba, Structural and mechanical aspects of hypoeutectic zn-mg binary alloys for biodegradable vascular stent applications. Bioactive Materials 6(1), 26–44 (2021)10.1016/j.bioactmat.2020.07.004 ↗
10. A. Jarzębska, M. Bieda, Ł. Maj, R. Chulist, D. Wojtas, M. Strąg, B. Sułkowski, S. Przybysz, W. Pachla, and K. Sztwiertnia, Controlled Grain Refinement of Biodegradable Zn-Mg Alloy: The Effect of Magnesium Alloying and Multi-Pass Hydrostatic Extrusion Preceded by Hot Extrusion. Metall. Mater. Trans. A 51, 6784–6796 (2020). https://doi.org/10.1007/s11661-020-06032-410.1007/s11661-020-06032-4 ↗
11. A. Jarzębska, M. Bieda, J. Kawałko, P. Koprowski, K. Sztwiertnia, W. Pachla, M. Kulczyk, A new approach to plastic deformation of biodegradable zinc alloy with magnesium and its effect on microstructure and mechanical properties. Materials Letters 211, 58–61 (2018)10.1016/j.matlet.2017.09.090 ↗
12. A. Jarzębska, M. Bieda, J. Kawałko, P. Koprowski, Ł. Rogal, R. Chulist, B. Kania, K. Sztwiertnia, W. Pachla, and M. Kulczyk: in: IOP Conference Series: Materials Science and Engineering, Vol. 375 (IOP Publishing, 2018), p. 012008.10.1088/1757-899X/375/1/012008 ↗
13. L. Cauvin, B. Raghavan, S. Bouvier, X. Wang, F. Meraghni, Multi-scale investigation of highly anisotropic zinc alloys using crystal plasticity and inverse analysis. Mater. Sci. Eng. A 729, 106–118 (2018)10.1016/j.msea.2018.05.038 ↗
14. M. Luo, G. Rousselier, Modeling of large strain multi-axial deformation of anisotropic metal sheets with strength-differential effect using a reduced texture methodology. Int. J. Plast. 53, 66–89 (2014)10.1016/j.ijplas.2013.07.006 ↗
15. D.E. Solas, C.N. Tomé, O. Engler, H.R. Wenk, Deformation and recrystallization of hexagonal metals: modeling and experimental results for zinc. Acta Mater. 49(18), 3791–3801 (2001)10.1016/S1359-6454(01)00261-0 ↗
16. R. Parisot, S. Forest, A. Pineau, F. Grillon, X. Demonet, J.-M. Mataigne, Deformation and damage mechanisms of zinc coatings on hot-dip galvanized steel sheets: Part I. deformation modes. Metall. Mater. Trans. A 35(3), 797–811 (2004)10.1007/s11661-004-0007-x ↗
17. O. Casals, S. Forest, Finite element crystal plasticity analysis of spherical indentation in bulk single crystals and coatings. Comput. Mater. Sci. 45(3), 774–782 (2009)10.1016/j.commatsci.2008.09.030 ↗
18. J.W. Christian, S. Mahajan, Deformation twinning. Prog. Mater. Sci. 39, 1–157 (1995)10.1016/0079-6425(94)00007-7 ↗
19. T. Skippon, C. Mareau, M.R. Daymond, On the determination of single-crystal plasticity parameters by diffraction: optimization of a polycrystalline plasticity model using a genetic algorithm. Journal of Applied Crystallography 45(4), 627–643 (2012)10.1107/S0021889812026854 ↗
20. K. Frydrych: Modelling of microstructure evolution of high specific strength metals subjected to severe plastic deformation processes., Ph.D. thesis, Institute of Fundamental Technological Research, Polish Academy of Sciences, Warsaw, Poland, 2017, (in Polish). https://doi.org/10.13140/RG.2.2.32354.56008.10.13140/RG.2.2.32354.56008 ↗
21. G. Girard, K. Frydrych, K. Kowalczyk-Gajewska, M. Martiny, S. Mercier, Mech. Mater. (2021). https://doi.org/10.1016/j.mechmat.2020.103685.10.1016/j.mechmat.2020.103685 ↗
22. V.M. Miller, S.L. Semiatin, C. Szczepanski, A.L. Pilchak, Optimization of vpsc model parameters for two-phase titanium alloys: Flow stress vs orientation distribution function metrics. Metall. Mater. Trans. A 49(8), 3624–3636 (2018)10.1007/s11661-018-4716-y ↗
23. K. Topolski, W. Pachla, H. Garbacz, Progress in hydrostatic extrusion of titanium. Journal of materials science 48(13), 4543–4548 (2013)10.1007/s10853-012-7086-7 ↗
24. F. Bachmann, R. Hielscher, and H. Schaeben: in: Texture and Anisotropy of Polycrystals III, Vol. 160 of Solid State Phenomena (Trans Tech Publications Ltd, 2010), pp. 63–68.10.4028/www.scientific.net/SSP.160.63 ↗
25. G.Y. Chin, W.F. Hosford, D.R. Mendorf, Accomodation of constrained deformation in f.c.c. metals by slip and twinning. Proc. R. Soc. A 309, 433–456 (1969)
26. P. Van Houtte, Simulation of the rolling texture and shear texture of brass by the Taylor theory adapted for mechanical twinning. Acta Metall. 26, 591–604 (1978). https://doi.org/10.1016/0001-6160(78)90111-610.1016/0001-6160(78)90111-6 ↗
27. M.S. Szczerba, T. Bajor, T. Tokarski, Is there a critical resolved shear stress for twinning in face-centered cubic crystals? Phil. Mag. 84, 481–502 (2004)10.1080/14786430310001612175 ↗
28. A. Molinari, G.R. Canova, S. Ahzi, Self-consistent approach of the large deformation polycrystal visco-plasticity. Acta Metall. 35, 2983–2994 (1987). https://doi.org/10.1016/0001-6160(87)90297-510.1016/0001-6160(87)90297-5 ↗
29. R.A. Lebensohn, C.N. Tomé, A self-consistent anisotropic approach for the simulation of plastic deformation and texture development of polycrystals: Application to zirconium alloys. Acta Metall. Mater. 41, 2611–2624 (1993). https://doi.org/10.1016/0956-7151(93)90130-K10.1016/0956-7151(93)90130-K ↗
30. C.N. Tomé and R.A. Lebensohn: Manual for Code Visco-Plastic Self-Consistent (VPSC). Version 7b, Technical representation, Los Alamos National Laboratory (2007).
31. K. Kowalczyk-Gajewska, Modelling of texture evolution in metals accounting for lattice reorientation due to twinning. Eur. J. Mech. Solids/A 29, 28–41 (2010). https://doi.org/10.1016/j.euromechsol.2009.07.00210.1016/j.euromechsol.2009.07.002 ↗
32. K. Kowalczyk-Gajewska: Micromechanical modelling of metals and alloys of high specific strength. IFTR Reports 1(2011), 1–299 (2011)
33. J. Arabas: Wykłady z algorytmów ewolucyjnych. (Lectures on evolutionary algorithms), Wydawnictwa Naukowo-Techniczne (2004), (in Polish).
34. M.W. Gutowski: Biology, physics, small worlds and genetic algorithms, Leading Edge Computer Science Research, Nova Science Publishers, Inc. pp. 165–218 (2005).
35. R. Hielscher and H. Schaeben: A novel pole figure inversion method: specification of the MTEX algorithm. Journal of Applied Crystallography 41(6), 1024–1037 (2008). https://doi.org/10.1107/S002188980803011210.1107/S0021889808030112 ↗
36. B. Beausir and J.J. Fundenberger: ATEX-software, Analysis Tools for Electron and X-ray Diffraction. http://atex-software.eu/.