On Shear Testing of Single Crystal Ni-Base Superalloys
Source abstract
Abstract
Abstract Shear testing can contribute to a better understanding of the plastic deformation of Ni-base superalloy single crystals. In the present study, shear testing is discussed with special emphasis placed on its strengths and weaknesses. Key mechanical and microstructural results which were obtained for the high-temperature (T ≈ 1000 °C) and low-stress (τ ≈ 200 MPa) creep regime are briefly reviewed. New 3D stereo STEM images of dislocation substructures which form during shear creep deformation in this regime are presented. It is then shown which new aspects need to be considered when performing double shear creep testing at lower temperatures (T < 800 °C) and higher stresses (τ > 600 MPa). In this creep regime, the macroscopic crystallographic [11−2](111) shear system deforms significantly faster than the [01−1](111) system. This represents direct mechanical evidence for a new planar fault nucleation scenario, which was recently suggested (Wuet al. in Acta Mater 144:642–655, 2018). The double shear creep specimen geometry inspired a micro-mechanicalin-situshear test specimen. Moreover, thein-situSEM shear specimen can be FIB micro-machined from prior dendritic and interdendritic regions. Dendritic regions, which have a lowerγ′ volume fraction, show a lower critical resolved shear stress.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High Temperature Alloys and Creep · Microstructure and mechanical properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (65)
Show source-provided references
1. Reed, R. C., The Superalloys: Fundamentals and Applications, Cambridge University Press, Cambridge, 2006.10.1017/CBO9780511541285 ↗
2. T.M. Pollock and S.Tin: J. Propul. Power, 2006, 22, pp. 361-374.10.2514/1.18239 ↗
3. A.B. Parsa, P. Wollgramm, H. Buck, C. Somsen, A. Kostka, I. Povstugar, P. Choi, D. Raabe, A. Dlouhy, J. Müller, E. Spiecker, K. Demtröder, J. Schreuer, K. Neuking and G. Eggeler: Adv. Eng. Mater., 2015, 17, pp. 216-230.10.1002/adem.201400136 ↗
4. V. Yardley, I. Povstugar, P.P. Choi, D. Raabe, A.B. Parsa, A. Kostka, C. Somsen, A. Dlouhy, K. Neuking, E. George and G. Eggeler: Adv. Eng. Mater., 2016, 18, pp. 1556-1567.10.1002/adem.201600237 ↗
5. C. Mayr, G. Eggeler, G.A. Webster and G. Peter: Mater. Sci. Eng., A, 1995, 199, pp. 121-130.10.1016/0921-5093(94)09721-6 ↗
6. American Society for Testing Materials, ASTM Special Publication No. 289, Symposium on Shear and Torsion Testing, ASTM, Philadelphia, 1961.
7. J.-P. Bardet: Experimental Soil Mechanics, Prentice Hall, New Jersey, 1997.
8. A. Bertram, J. Olschewski and M. Zelewski: Z. Angew. Math. Mech., 1991, 71, pp. 387-390.
9. P.R. Parselay, C.H. Wells, G.R. Leverant and L.H. Burck: J. Appl. Mech., 1971, 104, pp. 623-626.
10. N. Ohno, T. Mizuno, H. Kawaji and I. Okada: Acta Metall. Mater., 1992, 40, pp. 559–567.10.1016/0956-7151(92)90405-4 ↗
11. D.Nouhailhas, G.Cailletaud: Int. Journ. Plasticity, 1995, 11, pp. 451-470.10.1016/S0749-6419(98)80004-1 ↗
12. A. Matsuda: Trans. Jpn. Inst. Met., 1977, 18:214-220.10.2320/matertrans1960.18.214 ↗
13. W. Funk and E.Blank: Mater. Sci. Eng., 1984, 67, pp. 1-11.10.1016/0025-5416(84)90025-9 ↗
14. H. Raoult-Rogez: Thesis, Laboratoire de Thermodynamique et Physico-Chimie Métallurgiques (E.N.S.E.E.G.), Institut National Polytechnique, Grenoble, 1989.
15. D.M. Schwartz, J.B Mitchell and J.E. Dorn: Acta Metall., 1967, 15, pp. 485-490.10.1016/0001-6160(67)90080-6 ↗
16. F. Touratier, E. Andrieu, D. Pouquillon and B. Viguier: Mater. Sci. Eng., A, 2009, 510-511, pp. 244-249.10.1016/j.msea.2008.04.100 ↗
17. J. Henderson and J.D. Sneddon: J. Inst. Met., 1972, 100, pp. 163-171.
18. C. Roche: Thesis, Universite P. & M. Curie, Paris, 1976.
19. U. von Alpen and J.C. Doukhan, Rev. Sci. Instrum., 1977, 48, pp. 640-642.10.1063/1.1135097 ↗
20. M. Arcan, Z. Hashin and A. Voloshin: Exp. Mech., 1978, 18, pp. 141-146.10.1007/BF02324146 ↗
21. G. Peter, M. Probst-Hein, M. Kolbe, K. Neuking and G. Eggeler: Materialwiss. Werkstofftech., 1997, 28, pp. 457-464.10.1002/mawe.19970281006 ↗
22. C. Mayr, G. Eggeler and A. Dlouhy: Mater. Sci. Eng., A, 1996, 207, pp. 51-63.10.1016/0921-5093(96)80002-5 ↗
23. L.M. Pan, I. Scheibli, M.B. Henderson and M. McLean: Asymmetric creep deformation of a single-crystal superalloy: Acta Metall. Mater., 1995, 43, pp. 1375-1384.10.1016/0956-7151(94)00383-S ↗
24. L.M. Pan, B.A. Shollock and M. McLean: P. Roy. Soc. A-Math. Phy., 1997, 453, pp. 1689-1715.10.1098/rspa.1997.0091 ↗
25. T. Kruml, J.L. Martin, B. Viguier, J. Bonneville and P. Spätig: Mater. Sci. Eng., A, 1997, 240, pp. 174-179.10.1016/S0921-5093(97)00578-9 ↗
26. M. Kolbe, A. Dlouhy and G. Eggeler: Mater. Sci. Eng., A, 1998, 246, pp. 133-142.10.1016/S0921-5093(97)00733-8 ↗
27. G. Eggeler and A. Dlouhy: Acta Mater., 1997, 45, pp. 4251-4262.10.1016/S1359-6454(97)00084-0 ↗
28. R. Srinivasan, G. Eggeler and M.J. Mills: Acta Mater., 2000, 48, pp. 4867-4878.10.1016/S1359-6454(00)00292-5 ↗
29. P.M. Sarosi, R. Srinivasan, G. Eggeler, M.V. Nathal and M.J.Mills: Acta Mater., 2007, 55, pp. 2509-2518.10.1016/j.actamat.2006.11.045 ↗
30. L. Agudo Jácome, P. Noertershaeuser, C. Somsen, A. Dlouhy and G.Eggeler: Acta Mater., 2014, 69, pp. 246-264.10.1016/j.actamat.2014.01.021 ↗
31. A. Epishin and T. Link: Philos. Mag., 2004, 84, pp. 1979-2000.10.1080/14786430410001663240 ↗
32. A. Kostka, G. Mälzer, G. Eggeler, A. Dlouhy, S. Reese and T. Mack: J. Mater. Sci., 2007, 42, pp. 3951-3957.10.1007/s10853-006-0166-9 ↗
33. C. Carry, S. Dermarkar, J.L. Strudel and B.C. Wonsieicz: Metall. Mater. Trans. A, 1979, 10, pp. 855-860.10.1007/BF02658304 ↗
34. G.L. Drew, R.C. Reed, K. Kakehi and C.M.F. Rae: in Superalloys 2004, K. A. Green, et al. (Eds.), 2004, The Minerals, Metals and Materials Society, TMS, pp. 127-136.
35. M. Feller-Kniepmeier and T. Link: Metall. Mater. Trans. A, 1989, 20, pp. 1233-1238,10.1007/BF02647405 ↗
36. R.D. Field, T.M. Pollock and W.H. Murphy: in Superalloys 1992, Proceedings of the 7th International Symposium of Superalloys, edited by: S.D. Antolovich et al., TMS, Warrendale, 1992, pp. 557–66.10.7449/1992/Superalloys_1992_557_566 ↗
37. R.R. Keller, H.J. Maier and H. Mughrabi: Scr. Metall. Mater., 1993, 28, pp. 23-28.10.1016/0956-716X(93)90531-V ↗
38. M. Feller-Kniepmeier, U. Hemmersmeier, T. Kuttner and T.Link: Scr. Metall. Mater., 1994, 30, pp. 1275-1280.10.1016/0956-716X(94)90258-5 ↗
39. L. Agudo Jácome, P. Noertershaeuser, J.K. Heyer, A. Lahni, J. Frenzel, A. Dlouhy, C. Somsen and G. Eggeler: Acta Mater., 2013, 61, pp. 2926-2943.10.1016/j.actamat.2013.01.052 ↗
40. O. Paris, M. Fahrmann, E. Fahrmann, T.M. Pollock and P.Fratzl: Acta Mater., 1997, 45, pp. 1085-1097.10.1016/S1359-6454(96)00223-6 ↗
41. A. Epishin, T. Link and G. Nolze: J. Microsc, 2007, 228, pp. 110-117.10.1111/j.1365-2818.2007.01831.x ↗
42. T.Link, A.Epishin, M.Paulisch and T.May: Mater. Sci. Eng., A, 2011, 528, pp. 6225-6234.10.1016/j.msea.2011.04.049 ↗
43. V.A. Vorontsov, L. Kovarik, M.J. Mills and C.M.F.Rae: Acta Mater., 2012, 60, pp. 4866-4878.10.1016/j.actamat.2012.05.014 ↗
44. A.B. Parsa, P. Wollgramm, H. Buck, A. Kostka, C. Somsen, A. Dlouhy and G. Eggeler: Acta Mater., 2015, 90, pp. 105-117.10.1016/j.actamat.2015.02.005 ↗
45. F. Louchet and M. Ignat: Acta Metall., 1986, 34, pp. 1681-1686.10.1016/0001-6160(86)90114-8 ↗
46. R. Bonnet and A. Ati:, Acta Metall., 1989, 37, pp. 2153-2169.10.1016/0001-6160(89)90141-7 ↗
47. M.C. Carroll, K. Serin and G.Eggeler: Mater. Sci. Eng., A, 2004, 387, pp. 590-594.10.1016/j.msea.2004.03.098 ↗
48. M. Kamaraj, C. Mayr, M. Kolbe and G. Eggeler: Scr. Metall. Mater., 1998, 38, pp. 589-594.10.1016/S1359-6462(97)00520-4 ↗
49. K. Serin, G. Göbenli and G. Eggeler: Mater. Sci. Eng., A, 2004, 387-389, pp. 133-137.10.1016/j.msea.2004.01.114 ↗
50. M. Kamaraj, K. Serin, M. Kolbe, K. Neuking and G. Eggeler: Materialwiss. Werkstofftech., 2003, 34, pp. 469-477.10.1002/mawe.200390095 ↗
51. P. Wollgramm, H., K. Neuking, A. Parsa, S. Schuwalow, J. Rogal, R. Drautz and G. Eggeler: Mater. Sci. Eng., A, 2015, 628, pp. 382-395.10.1016/j.msea.2015.01.010 ↗
52. G. Eggeler: Mater. Sci. Technol., 2009, 25, pp. 236-241.10.1179/174328408X355424 ↗
53. http://www.sfb-transregio103.de, March 12th 2018.
54. L.A. Jácome, G. Göbenli and G. Eggeler: J. Mater. Res., 2017, 32, pp. 4491-4502.10.1557/jmr.2017.336 ↗
55. L. Agudo Jácome, G. Eggeler and A. Dlouhy, Advanced scanning transmission electron microscopy of structural and functional engineering materials, Ultramicroscopy, 2012, 122, pp. 48-59.
56. P. Caron, Y. Ohta, Y.G. Nakagawa and T. Khan (1988). In: S. Reichmann et al. (Eds) Superaloys. The Metallurgical Society TMS, Warrendale, pp. 215–224.
57. S. Gao, P. Wollgramm, G. Eggeler, A. Ma, J. Schreuer and A. Hartmaier: Modell. Simul. Mater. Sci. Eng., 2018, vol. 26, pp. 055001.10.1088/1361-651X/aabdbe ↗
58. P. Wollgramm, D. Bürger, A.B. Parsa, K. Neuking and G. Eggeler: Mater. High Temp., 2016, 33, pp. 346-360.10.1080/09603409.2016.1186414 ↗
59. X. Wu, A. Dlouhy, Y.M. Eggeler, E. Spiecker, A. Kostka, C. Somsen and G. Eggeler: Acta Mater., 2018, 144, pp. 642-655.10.1016/j.actamat.2017.09.063 ↗
60. C.M.F.Rae and R.C.Reed: Acta Mater., 2007, 55, pp. 1067–1081.10.1016/j.actamat.2006.09.026 ↗
61. J.K. Heyer, S. Brinckmann, J. Pfetzing-Micklich and G. Eggeler: Acta Mater., 2014, 62, pp. 225-238.10.1016/j.actamat.2013.10.002 ↗
62. N. Wieczorek, G. Laplanche, J.K. Heyer, A.B. Parsa, J. Pfetzing-Micklich and G.Eggeler: Acta Mater., 2016, 113, pp. 320-334.10.1016/j.actamat.2016.04.055 ↗
63. E.Nembach, Particle strengthening of metals and alloys, John Wiley and Sons, New York, 1997.
64. C. Tromas, M. Arnoux, X. Milhet: Scripta Mater., 2012, 66, pp. 77-80.10.1016/j.scriptamat.2011.09.042 ↗
65. P.Caron, in: Superalloys 2000, edited by: T. Pollock et al., TMS, Warrendale, 2000, pp. 737-764.10.7449/2000/Superalloys_2000_737_746 ↗