journal article·2025-01Open access

Effect of Horizontal Continuous Casting Parameters on Cyclic Macrosegregation, Microstructure, and Properties of High-Strength Cu–Mg Alloy Cast Rod

Paweł Strzępek, Andrzej Mamala, Zakaria Boumerzoug, Thierry Baudin, François Brisset, Małgorzata Zasadzińska, Piotr Noga

Abstract

Abstract The objective of this paper is to present the effect of horizontal continuous casting parameters on macrosegregation and its effect on microstructures, textures, mechanical properties, and electrical resistivity of Cu–Mg alloy rod. By increasing the pulling distance and intermittent extraction time, chemical macrosegregation was observed along the longitudinal section of the cast rod, which reached a distance of 40 mm. Three areas were identified along the length of the material, especially at high pulling distance: with decreasing, quasi-stable, and increasing Mg concentration area. As the pulling distance increased, the difference in the observed extreme values of Mg concentration increased. Two distinct zones of different grain size were also observed. The first zone was formed of large columnar grains with a preferred direction of solidification $$\langle 100\rangle$$ inclined to the axis of the wire, followed by a second zone formed of small grains of random texture. Consequently, difference in resistivity occurred from one zone to another and the resistivity increased from 37.5 to 41 nΩm. Likewise, the hardness varied between the values of 90 up and 110 Hv. The most homogenous chemical composition was obtained with up to 6 mm of pulling distance and up to 3 seconds of intermittent extraction time.
Source: crossref · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (60)

Show source-provided references
1. Copper Development Association: The Copper Advantage, A Guide to Working with Copper and Copper Alloys, Report. Copper Development Association, New York, 2009. https://www.copper.org/publications/pub_list/pdf/a1360.pdf. Accessed 7 July 2023.
2. D.E. Tyler and W.T. Black: ASM Handbook: Properties and Selection: Nonferrous Alloys and Special-Purpose Material, 1990. https://doi.org/10.31399/asm.hb.v02.a0001065.10.31399/asm.hb.v02.a0001065 ↗
3. Five Applications for Copper Alloy Wire. https://www.bobmartinco.com/five-applications-for-copper-alloy-wire/. Accessed 7 Dec 2023.
4. K.J.A. Kundig and J.G. Cowie: In: M. Kutz (ed) Mechanical Engineers' Handbook: Materials and Mechanical Design, Vol. 1, 3rd edn, 2005. https://doi.org/10.1002/0471777447.ch4.10.1002/0471777447.ch4 ↗
5. J. Jacobsen: Proc. Copper, 2010, pp. 99–118.
6. H. Sommerhofer and P. Sommerhofer: Proc. Int. Congr. Contin. Cast. Non-ferr. Met., November 2006, DGM Deutch Gesellschaft fur Materialkundee.v., Neu Ulm, pp. 368–76.10.1002/9783527607969.ch49 ↗
7. V. Plochikhine, V. Karkhin, and H. Bergmann: Proc. Int. Congr. ‘Continuous casting’, November 2000, DGM Deutch Gesellschaft fur Materialkundee.v., Frankfurt/Main, pp. 109–15.10.1002/3527607331.ch16 ↗
8. E.-R. Bagherian, Y. Fan, M. Cooper, B. Frame, and A. Abdolvand: Metall. Res. Technol., 2016, vol. 113(5), p. 502. https://doi.org/10.1051/metal/2016030.10.1051/metal/2016030 ↗
9. V. Arbabi and I. Ebrahimzadeh: Int. J. Cast Met., 2010, vol. 23(3), pp. 150–57. https://doi.org/10.1179/136404609X12490478029353.10.1179/136404609X12490478029353 ↗
10. P. Pelzl: Dipl.-Ing. Peter Pelzl., Sulzer Brothers Ltd., Winterthur, 1969.
11. D. Kopeliovich: Horizontal Continuous Casting in Graphite Mold, Foundry Technologies, 2012. https://www.substech.com/dokuwiki/doku.php?id=horizontal_continuous_casting_in_graphite_mold. Accessed 7 Dec 2023.
12. R. Wilson: A Practical Approach to Continuous Casting of Copper-Based Alloys and Precious Metals, IOM Communications, University of Michigan, 2000.
13. J.M. Rodriguez, A. Esteva, and S. Meza: J. Mater. Process. Technol., 1999, vol. 96(1–3), pp. 42–47. https://doi.org/10.1016/S0924-0136(99)00314-3.10.1016/S0924-0136(99)00314-3 ↗
14. J.M. Rodriguez and J. Montecinos: Wire, 1991, vol. 41(5), pp. 409–14.
15. M. Vynnycky, S. Saleem, and H. Fredriksson: Appl. Math. Model., 2018, vol. 54, pp. 605–26. https://doi.org/10.1016/j.apm.2017.10.012.10.1016/j.apm.2017.10.012 ↗
16. A.V. Reddy and C. Beckermann: Metall. Mater. Trans. B, 1997, vol. 28B, pp. 479–89. https://doi.org/10.1007/s11663-997-0115-2.10.1007/s11663-997-0115-2 ↗
17. S. Saleem, M. Vynnycky, and H. Fredriksson: Proc. Miner. Met. Mater. Soc. (TMS), 2015, 144th Annu. Meet. Exhib., Orlando, Florida, pp. 15–22.10.1007/978-3-319-48117-3_3 ↗
18. M. Li, T. Mori, and H. Iwasaki: ISIJ Int., 1999, vol. 39(1), pp. 33–38. https://doi.org/10.2355/isijinternational.39.33.10.2355/isijinternational.39.33 ↗
19. S. Gorsse, B. Ouvrard, M. Gouné, and A. Poulon-Quintin: J. Alloys Compd., 2015, vol. 663, pp. 42–47. https://doi.org/10.1016/j.jallcom.2015.01.234.10.1016/j.jallcom.2015.01.234 ↗
20. M. Nairn: WAI Technical Conference at Interwire, Georgia World Congress Center, April 2013, Atlanta, Georgia, USA.
21. L. Song, Y. Yuan, and Z. Yin: Int. J. Nonferr. Met., 2013, vol. 2, pp. 100–05. https://doi.org/10.4236/ijnm.2013.23014.10.4236/ijnm.2013.23014 ↗
22. P. Strzepek, A. Mamala, M. Zasadzinska, P. Noga, and M. Sadzikowski: Materials, 2020, vol. 13(21), p. 4805. https://doi.org/10.3390/ma13214805.10.3390/ma13214805 ↗
23. A.A. Nayeb-Hashemi and J.B. Clark: Bull. Alloy Phase Diagr., 1984, vol. 5(1), pp. 36–43. https://doi.org/10.1007/BF02868722.10.1007/BF02868722 ↗
24. J.I. Goldstein, D.E. Newbury, et al.: Scanning Electron Microscopy and X-Ray Microanalysis, Kluwer Academic/Plenum Publishers, New York, 2003. https://doi.org/10.1007/978-1-4615-0215-9.10.1007/978-1-4615-0215-9 ↗
25. Y.H. Wang, L.R. Xiao, X.J. Zhao, W. Hu, Y.F. Song, W. Zhang, and H. Zhou: Mater. Sci. Eng. A, 2015, vol. 639, pp. 122–30. https://doi.org/10.1016/j.msea.2015.04.099.10.1016/j.msea.2015.04.099 ↗
26. J. Mahmoudi and H. Nabati: Int. J. Green Energy, 2006, vol. 3(2), pp. 185–99. https://doi.org/10.1080/01971520500544044.10.1080/01971520500544044 ↗
27. Z. Lu, Z.-J. Sun, Z.-H. Hou, Z.-Y. Yang, X.-L. Zhang, and Y.-D. Shi: High Temp. Mater. Process., 2022, vol. 41(1), pp. 1–7. https://doi.org/10.1515/htmp-2022-0012.10.1515/htmp-2022-0012 ↗
28. T. Knych, B. Smyrak, and M. Walkowicz: Electr. Rev., 2011, vol. 87(9a), pp. 285–90. https://www.researchgate.net/publication/267411152. Accessed 7 Dec 2023.
29. D.-C. Tsai, M.-S. Hsu, W.-S. Hwang, and C.-S. Jiang: ISIJ Int., 2010, vol. 50(12), pp. 1843–50. https://doi.org/10.2355/isijinternational.50.1843.10.2355/isijinternational.50.1843 ↗
30. D. Walton and B. Chalmers: Trans Metall. Soc. AIME, 1959, vol. 215, pp. 447–57.
31. Y. Wang, H.Y. Huang, and J. Xie: Mater. Sci. Eng. A, 2011, vol. 530, pp. 418–25. https://doi.org/10.1016/j.msea.2011.09.105.10.1016/j.msea.2011.09.105 ↗
32. E.-R. Bagherian, Y. Fan, M. Cooper, B. Frame, and A. Abdolvand: Metall. Res. Technol., 2016, vol. 113, p. 308. https://doi.org/10.1051/metal/2016006.10.1051/metal/2016006 ↗
33. J. Hunt: Mater. Sci. Eng., 1984, vol. 65(1), pp. 75–83. https://doi.org/10.1016/0025-5416(84)90201-5.10.1016/0025-5416(84)90201-5 ↗
34. O.L. Rocha, L.G. Gomez, D.J.C. Moutinho, I.L. Ferreira, and A. Garcia: Metall. Mater. REM Ouro Preto, 2015, vol. 68(1), pp. 85–90. https://doi.org/10.1590/0370-44672015680237.10.1590/0370-44672015680237 ↗
35. M.J. Balart, J.B. Patel, F. Gao, and Z. Fan: Metall. Mater. Trans. A, 2016, vol. 47A, pp. 4988–5011. https://doi.org/10.1007/s11661-016-3671-8.10.1007/s11661-016-3671-8 ↗
36. Y. Xu, D. Zhao, and Y. Li: Metall. Mater. Trans. A, 2018, vol. 49A(5), pp. 1770–81. https://doi.org/10.1007/s11661-018-4542-2.10.1007/s11661-018-4542-2 ↗
37. L.A. Tarshis, J.L. Walker, and J.W. Rutter: Metall. Mater. Trans. B, 1971, vol. 2B, pp. 2589–97. https://doi.org/10.1007/BF02814899.10.1007/BF02814899 ↗
38. Y. Wang, C.M. Fang, L. Zhou, T. Hashimoto, X. Zhou, Q.M. Ramasse, and Z. Fan: Acta Mater., 2019, vol. 164, pp. 428–39. https://doi.org/10.1016/j.actamat.2018.10.056.10.1016/j.actamat.2018.10.056 ↗
39. F. Wang, D. Qiu, Z. Liu, J.A. Taylor, M.A. Easton, and M.X. Zhang: Acta Mater., 2013, vol. 61, pp. 5636–45. https://doi.org/10.1016/j.actamat.2013.05.044.10.1016/j.actamat.2013.05.044 ↗
40. Z. Lei, W. Shengping, H. Huang, W. Wei, and Z. Nie: Metals, 2023, vol. 13(4), p. 751. https://doi.org/10.3390/met13040751.10.3390/met13040751 ↗
41. F. Gao and Z. Fan: Metals, 2022, vol. 12(9), p. 1488. https://doi.org/10.3390/met12091488.10.3390/met12091488 ↗
42. Z. Fan, F. Gao, B. Jiang, and Z. Que: Sci. Rep., 2020, vol. 10, p. 9448. https://doi.org/10.1038/s41598-020-66190-8.10.1038/s41598-020-66190-8 ↗
43. J. Chen, X. Xiao, D. Yuan, C. Guo, H. Huang, and B. Yang: J. Alloys Compd., 2021, vol. 889, p. 161700. https://doi.org/10.1016/j.jallcom.2021.161700.10.1016/j.jallcom.2021.161700 ↗
44. M.C. Flemings: Solidification Processing, McGraw-Hill, New York, 1974.10.1007/BF02643923 ↗
45. J. Mahmoudi: Int. J. Cast Met. Res., 2005, vol. 18(6), pp. 355–69. https://doi.org/10.1179/136404605225023099.10.1179/136404605225023099 ↗
46. D.A. Porter, K.E. Easterling, and M.Y. Sherif: Phase Transformations in Metals and Alloys, CRC Press, Boca Raton, 2021. https://doi.org/10.1201/9781003011804.10.1201/9781003011804 ↗
47. X. Zhang, S. Friedrich, and B. Friedrich: J. Cryst. Process Technol., 2018, vol. 8, pp. 33–55. https://doi.org/10.4236/jcpt.2018.81003.10.4236/jcpt.2018.81003 ↗
48. G.F. Pfann: Zone Melting, Wiley, Hoboken, 1958.
49. E.D. Tolmie: J. Phys. E, 1960, vol. 37(5), pp. 175–77. https://doi.org/10.1088/0950-7671/37/5/308.10.1088/0950-7671/37/5/308 ↗
50. S.N. Ojha, G.L. Ding, Y. Lu, J. Reye, and S.N. Tewari: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 2167–71. https://doi.org/10.1007/s11661-999-0028-6.10.1007/s11661-999-0028-6 ↗
51. Y. Sawaragi and S. Hirano: New Alloys for Pressure Vessels and Piping, ASME Press, New York, 1990, pp. 141–46.
52. Y. Sawaragi, N. Otsuka, and H. Senba: Sumitomo Search, 1994, vol. 56, pp. 34–43.
53. T. Kan, Y. Sawaragi, Y. Yamadera, and H. Okada: Mater. Adv. Power Eng., 1998, vol. 4, pp. 441–50. https://core.ac.uk/download/pdf/45268386.pdf. Accessed 7 Dec 2023.
54. S.B. Ping, F. Xie, R.K. Wang, Z.J. Zheng, and Y. Gao: High Temp. Mater. Process., 2016, vol. 36(2), pp. 175–81. https://doi.org/10.1515/htmp-2015-0227.10.1515/htmp-2015-0227 ↗
55. Q. Zhang, J. Wu, S. Jiang, and G. He: Metals, 2022, vol. 12(2), p. 237. https://doi.org/10.3390/met12020237.10.3390/met12020237 ↗
56. K. Saito, M. Suzuki, S. Semboshi, K. Sato, and Y. Hayasaka: Mater. Trans., 2020, vol. 61(10), pp. 1912–21. https://doi.org/10.2320/matertrans.MT-M2020149.10.2320/matertrans.MT-M2020149 ↗
57. K. Hao, M. Gong, Y. Xie, M. Gao, and X. Zeng: Opt. Laser Technol., 2018, vol. 102, pp. 124–29. https://doi.org/10.1016/j.optlastec.2017.12.029.10.1016/j.optlastec.2017.12.029 ↗
58. G. Nolze: Ultramicroscopy, 2007, vol. 107, pp. 172–83. https://doi.org/10.1016/j.ultramic.2006.07.003.10.1016/j.ultramic.2006.07.003 ↗
59. L.P. Zhang, C.L. Davis, and M. Strangwood: Conf. Proc. Thermomech. Process. Steels, IOM Communications, 2000, pp. 764–75.
60. J.Z. He, Y.Z. Liu, B.H. Shi, Q.Y. Liu, X.L. Wang, and D.G. Li: KangT’ian Iron Steel (Peking), 2005, vol. 40(2), pp. 69–71.