The Defining Role of Micro-fissures on the Mechanical Behavior of Laser-Welded Fully Austenitic Stainless Steel
Source abstract
Abstract
Laser-welded fully austenitic stainless steel (AISI 316LN) weldments revealed the presence of micro-fissures. They appeared at the grain boundaries, near the center of the welds. The grain boundaries, however, did not contain second phase or micro-segregation. The relative presence of micro-fissures decreased with increasing weld heat input. Spatial locations of the micro-fissures and their relative presence were associated with local misorientations and, in particular, with grain reference orientation deviation. Microstructural and microtextural studies indicated that solidification shrinkage was the origin of the micro-fissures in the laser welds. The use of sub-size tensile specimens (of 5- and 1-mm gauge length) with digital image correlation (DIC) related the presence of micro-fissures with mechanical property degradation by the appearance of strain localizations. This was further confirmed by analytical solutions and finite element analysis of critical flaw size and critical stress for fracture.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (65)
Show source-provided references
1. K.S. Prasad, C.S. Rao, and D.N. Rao: J. Manuf. Sci. Prod., 2014, vol. 14, pp. 1–11.
2. V.P. Kujanpaa: Weld. J., 1983, vol. 62, pp. 45–52.
3. C.D. Lundin and C.P.D. Chou: Weld. J., 1985, vol. 64, pp. 113–18.
4. Y. Cui: PhD diss, University of Tennessee, 2004.
5. V. Kujanpää, N. Suutala, T. Takalo, and T. Moisio: Weld. Res. Int., 1979, vol. 9, pp. 55–76.
6. V. Shankar, T.P.S. Gill, A.L.E. Terrance, S.L. Mannan, and S. Sundaresan: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 3109–22.10.1007/s11661-000-0090-6 ↗
7. J. Yu, M. Rombouts, and G. Maes: Mater. Des., 2013, vol. 45, pp. 228–35.10.1016/j.matdes.2012.08.078 ↗
8. J. Brooks and A. Thompson: Int. Mater. Rev., 2011, vol. 19, pp. 16–44.
9. W. Guo, Q. Liu, J.A. Francis, D. Crowther, A. Thompson, Z. Liu, and L. Li: CIRP Ann. Manuf. Technol., 2015, vol. 64, pp. 197–200.10.1016/j.cirp.2015.04.070 ↗
10. M. Bachmann, V. Avilov, A. Gumenyuk, and M. Rethmeier: Phys. Procedia, 2014, vol. 56, pp. 515–24.10.1016/j.phpro.2014.08.006 ↗
11. B. Fotovvati, S.F. Wayne, G. Lewis, and E. Asadi: Adv. Mater. Sci. Eng., 2018, vol. 2018, pp. 1–18.10.1155/2018/4920718 ↗
12. L. Li, G. Peng, J. Wang, J. Gong, and S. Meng: Int. J. Heat Mass Transf., 2019, vol. 133, pp. 812–26.10.1016/j.ijheatmasstransfer.2018.12.165 ↗
13. S. Katayama, Y. Naito, S. Uchiumi, and M. Mizutani: Trans. JWRI, 2006, vol. 35, pp. 13–18.
14. Z. Jiang, X. Chen, H. Li, Z. Lei, Y. Chen, S. Wu, and Y. Wang: Mater. Des., 2020, vol. 186, p. 108195.10.1016/j.matdes.2019.108195 ↗
15. J. Hu and H.L. Tsai: in American Society of Mechanical Engineers, Proceeding of IMECE, vol. 374, 2003, pp. 151–59.
16. S. Kou: Acta Mater., 2015, vol. 88, pp. 366–74.10.1016/j.actamat.2015.01.034 ↗
17. D.G. Eskin and L. Katgerman: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 1511–19.10.1007/s11661-007-9169-7 ↗
18. M. Bellet, O. Cerri, M. Bobadilla, and Y. Chastel: Metall. Mater. Trans. A., 2009, vol. 40A, pp. 2705–17.10.1007/s11661-009-9955-5 ↗
19. M. Rappaz, J.M. Drezet, and M. Gremaud: Metall. Mater. Trans. A., 1999, vol. 30A, pp. 449–55.10.1007/s11661-999-0334-z ↗
20. V.P. Kujanpää, S.A. David, and C.L. White: Weld. Res., 1986, vol. 65, pp. 203–12.
21. L. Li and R.W. Messler Jr.: Weld. Res., 2003, vol. 78, pp. 387–96.
22. M.J. Cieslak, A.M. Ritter, and W.F. Savage: Weld. Res., 1982, vol. 61, pp. 1–8.
23. C.D. Lundin, C.-P.D. Chou, and C.J. Sullivan: Weld. J., 1980, vol. 59, pp. 226–32.
24. J.N. DuPont: Weld. Res., 1999, vol. 42, pp. 253–63.
25. N. Suutala: Metall. Trans. A, 1982, vol. 13A, pp. 2121–30.10.1007/BF02648382 ↗
26. S.A. David: Weld. J., 1981, vol. 60, pp. 63–71.
27. C.D. Lundin and D.F. Spond: Weld. J., 1976, vol. 55, pp. 22–25.
28. C.D. Lundin, W.T. Delong, and D.F. Spond: Weld. J., 1975, vol. 54, pp. 241–46.
29. F. Matsuda, H. Nakagawa, T. Uehara, S. Katayama, and Y. Arata: Trans. JWRI, 1979, vol. 8, pp. 105–12.
30. H.K.D.H. Bhadeshia, S.A. David, and J.M. Vitek: Mater. Sci. Technol., 1991, vol. 7, pp. 50–61.10.1179/mst.1991.7.1.50 ↗
31. D.J. Kotecki and T.A. Siewert: Weld. J., 1992, vol. 71, pp. 171–78.
32. T.A. Siewert, C.N. McCowan, and D.L. Olson: Weld. J., 1988, vol. 67, pp. 289–98.
33. D.L. Olson: Weld. J., 1985, vol. 64, pp. 281–95.
34. J. Lippold: Weld. J., 1994, vol. 73, pp. 129–39.
35. N. Suutala, T. Takalo, and T. Moisio: Metall. Trans. A, 1980, vol. 11A, pp. 717–25.10.1007/BF02661201 ↗
36. N. Suutala: Metall. Trans. A, 1983, vol. 14A, pp. 191–97.10.1007/BF02651615 ↗
37. W. Chuaiphan and L. Srijaroenpramong: J. Adv. Join. Process., 2020, vol. 2, p. 100027.10.1016/j.jajp.2020.100027 ↗
38. P. Datta and G.S. Upadhyaya: Mater. Chem. Phys., 2001, vol. 67, pp. 234–42.10.1016/S0254-0584(00)00477-6 ↗
39. J. Brooks, A. Thompson, and J. Williams: Weld. J., 1984, vol. 63, pp. 71–83.
40. M.V. Venkatesan, N. Murugan, S. Sam, and S.K. Albert: Trans. Indian Inst. Met., 2014, vol. 67, pp. 375–83.10.1007/s12666-013-0358-3 ↗
41. A.V. Bansod, A.P. Patil, A.P. Moon, and S. Shukla: J. Mater. Eng. Perform., 2017, vol. 26, pp. 5847–63.10.1007/s11665-017-3054-3 ↗
42. A.V. Bansod, A.P. Patil, and S. Shukla: Anti-Corros. Methods Mater., 2018, vol. 65, pp. 605–15.10.1108/ACMM-05-2018-1941 ↗
43. H. Vashishtha, R.V. Taiwade, S. Sharma, and A.S. Marodkar: Metallogr. Microstruct. Anal., 2019, vol. 8, pp. 359–69.10.1007/s13632-019-00549-w ↗
44. G.R. Mohammed, M. Ishak, S.N. Aqida, and H.A. Abdulhadi: Metals, 2017, vol. 7, pp. 1–18.10.3390/met7020039 ↗
45. D. Hauser and J.A. Vanecho: Weld. J., 1982, vol. 61, pp. 37–44.
46. S.S. Babu, J.M. Vitek, Y.S. Iskander, and S.A. David: Sci. Technol. Weld. Join., 1997, vol. 2, pp. 279–85.10.1179/stw.1997.2.6.279 ↗
47. T.N. Tak, A. Prakash, A. Lodh, S.M. Keralavarma, S.V.S. Narayana Murty, I. Samajdar, and P.J. Guruprasad: J. Eng. Mater. Technol. Trans. ASME, 2020, vol. 142, pp. 1–8.10.1115/1.4047498 ↗
48. J.C. Lippold and W.F. Savage: Weld. J., 1982, vol. 61, pp. 388–96.
49. T.J. Lienert and J.C. Lippold: Sci. Technol. Weld. Join., 2003, vol. 8, pp. 1–9.10.1179/136217103225008847 ↗
50. V. Tandon, M.A. Thombre, A.P. Patil, R.V. Taiwade, and H. Vashishtha: Metallogr. Microstruct. Anal., 2020, vol. 9, pp. 668–77.10.1007/s13632-020-00681-y ↗
51. A.M. Chelladurai, K.A. Gopal, S. Murugan, S.K. Albert, S. Venugopal, and T. Jayakumar: Sci. Technol. Weld. Join., 2015, vol. 20, pp. 578–84.10.1179/1362171815Y.0000000041 ↗
52. A.M. Chelladurai, K.A. Gopal, S. Murugan, S. Venugopal, and T. Jayakumar: Mater. Manuf. Processes, 2015, vol. 30, pp. 162–68.10.1080/10426914.2014.965829 ↗
53. M. Montazeri, F. Malek Ghaini, and O.A. Ojo: Weld. J., 2013, vol. 92, pp. 258–64.
54. K. Nishimoto and H. Mori: Sci. Technol. Adv. Mater., 2004, vol. 5, pp. 231–40.10.1016/j.stam.2003.10.006 ↗
55. S. Kumar and A.S. Shahi: Mater. Des., 2011, vol. 32, pp. 3617–23.10.1016/j.matdes.2011.02.017 ↗
56. H. Vashishtha, R.V. Taiwade, R.K. Khatirkar, A.V. Ingle, and R.K. Dayal: ISIJ Int., 2014, vol. 54, pp. 1361–67.10.2355/isijinternational.54.1361 ↗
57. Y. Cui and C.D. Lundin: J. Mater. Sci., 2005, vol. 40, pp. 1281–83.10.1007/s10853-005-6952-y ↗
58. Y. Cui, C.D. Lundin, and V. Hariharan: J. Mater. Process. Technol., 2006, vol. 171, pp. 150–55.10.1016/j.jmatprotec.2005.06.065 ↗
59. S. Basu, B.N. Jaya, A. Patra, S. Ganguly, M. Dutta, A. Hohenwarter, and I. Samajdar: Metall. Mater. Trans. A, 2021, vol. 52A, pp. 4018–32.10.1007/s11661-021-06361-y ↗
60. G. Sasikala and S.K. Ray: J. Nucl. Mater., 2011, vol. 408, pp. 45–53.10.1016/j.jnucmat.2010.11.001 ↗
61. P. Ganesh, R. Kaul, G. Sasikala, H. Kumar, S. Venugopal, P. Tiwari, S. Rai, R.C. Prasad, and L.M. Kukreja: Metallogr. Microstruct. Anal., 2014, vol. 3, pp. 36–45.10.1007/s13632-013-0115-3 ↗
62. W. Gao, K. Chen, X. Guo, and L. Zhang: Mater. Sci. Eng. A, 2017, vol. 685, pp. 107–14.10.1016/j.msea.2016.12.128 ↗
63. E.J. Chun, K. Nishimoto, and K. Saida: Weld. World, 2016, vol. 60, pp. 217–31.10.1007/s40194-016-0293-0 ↗
64. T.L. Anderson: Fracture Mechanics Fundamentals and Applications, 2nd ed. CRC Press, Boca Raton, 1995.
65. M.F. Ashby: Materials Selection in Mechanical Design, 3rd ed. Butterworth-Heinemann, Oxford, 2005.