Role of Steel Plate Thickness on the Residual Stress Formation and Cracking Behavior During Flame Cutting
Source abstract
Abstract
Abstract Thick wear-resistant steel plates are utilized in challenging applications, which require a high hardness and toughness. However, utilization of the thick plates is problematic as they often have nonuniform mechanical properties along the thickness direction due to the manufacturing-induced segregations. In addition, the processing of thick plates commonly involves flame cutting, which causes several challenges. Flame cutting forms a heat-affected zone and generates high residual stresses during the cutting process. In the worst case, flame cutting causes cracking of the cut edge. The aim of this study is to investigate the role of plate thickness on the residual stress formation and cracking behavior when utilizing flame cutting. Residual stress profiles are measured by X-ray diffraction, plates and cut edges and are mechanically tested and characterized by electron microscopy. The results show that thicker plates generate more unfavorable residual stress state during flame cutting. Thick plates also contain segregations, which have decreased mechanical properties. The combination of high residual tensile stresses and segregations increase the risk of cracking during flame cutting. To prevent the cracking, the residual stresses should be lowered by lower cutting speeds and preheating. In addition, manufacturing practices should be aimed at lowering segregation formation in thick plates.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Metal Alloys Wear and Properties · Surface Treatment and Residual Stress
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (23)
Show source-provided references
1. [1] N. Yang, C. Su, X. Wang, and F. Bai: J. Construct. Steel Res., 2016, vol. 122, pp. 213-25.10.1016/j.jcsr.2016.03.014 ↗
2. [2] Y. Wang, X. Liu, Z. Hu, and Y. Shi: Fatigue Fract. Eng. Mater. Struct., 2013, vol. 36, pp. 1258-73.10.1111/ffe.12062 ↗
3. [3] Y. Wang, X. Liao, Y. Zhang, and Y. Shi: J. Zhejiang Univ. Sci. A, 2015, vol. 16, pp. 217-28.10.1631/jzus.A1400273 ↗
4. [4] L.R. Soisson: Oxyfuel Gas Cutting, Welding, Brazing, and Soldering, Vol 6, ASM International, ASM Handbook, 1993, pp. 1155-65.
5. [5] R. Thiébaud, J. Drezet, and J. Lebet: J. Mater. Process. Technol., 2014, vol. 214, pp. 304-10.10.1016/j.jmatprotec.2013.09.016 ↗
6. W. Wood: Report No. FHWA-RD-93-015, U.S. Department of Transportation, Federal Highway Administration, Virginia, 1994.
7. [7] A. Martín-Meizoso, J. Aldazabal, J.L. Pedrejón, and S. Moreno: Frattura Ed Integrita Strutturale, 2014, vol. 30, pp. 14-22.10.3221/IGF-ESIS.30.03 ↗
8. [8] A.D. Wilson: Eng. J., 1990, vol. 27, pp. 98-107.10.62913/engj.v27i3.554 ↗
9. T. Jokiaho, S. Santa-Aho, H. Järvinen, M. Honkanen, P. Peura, and M. Vippola: Mater. Perform. Charact., 2018, vol. 7, pp. 655-74.10.1520/MPC20170083 ↗
10. [10] P. Withers and H. Bhadeshia: Mater. Sci. Technol., 2001, vol. 17, pp. 355-65.10.1179/026708301101509980 ↗
11. [11] P. Withers and H. Bhadeshia: Mater. Sci. Technol., 2001, vol. 17, pp. 366-75.10.1179/026708301101510087 ↗
12. [12] L. Lindgren, A. Carlestam, and M. Jonsson: J. Eng. Mater. Technol., 1993, vol. 115, pp. 440-45.10.1115/1.2904243 ↗
13. [13] T. Jokiaho, A. Laitinen, S. Santa-aho, M. Isakov, P. Peura, T. Saarinen, A. Lehtovaara, and M. Vippola: Metall. Mater. Trans. B, 2017, vol. 48, pp. 2891-901.10.1007/s11663-017-1090-x ↗
14. [14] T. Jokiaho, T. Saarinen, S. Santa-Aho, P. Peura, and M. Vippola: Key Eng. Mater., 2016, vol. 674, pp. 103-08.10.4028/www.scientific.net/KEM.674.103 ↗
15. [15] H. Bhadeshia and R. Honeycombe: Steels: Microstructure and Properties, 4th ed., Butterworth-Heinemann, Oxford, U.K., 2017, pp. 387-88.
16. EN 15305: Non-destructive Testing Method for Residual Stress analysis by X-ray Diffraction, 2008.
17. SFS-EN ISO 6892-1: Mechanical Engineering and Metals Industry Standardization in Finland, 2016, .
18. SFS-EN ISO 148-1: Mechanical Engineering and Metals Industry Standardization in Finland, 2016.
19. [19] K. Abbaszadeh, H. Saghafian, and S. Kheirandish: J. Mater. Sci. Technol., 2012, vol. 28, pp. 336-42.10.1016/S1005-0302(12)60065-6 ↗
20. [20] C. Zhang, Q. Wang, J. Ren, R. Li, M. Wang, F. Zhang, and K. Sun: Mater. Sci. Eng. A, 2012, vol. 534, pp. 339-46.10.1016/j.msea.2011.11.078 ↗
21. [21] T. Zhou, H. Yu, and S. Wang: Mater. Sci. Eng. A, 2016, vol. 658, pp. 150-58.10.1016/j.msea.2016.02.001 ↗
22. [22] H. Bhadeshia: Bainite in Steels, 2nd ed., Institute of Materials, London, U.K., 2001, pp. 91-116.
23. [23] H. Bhadeshia and R. Honeycombe: Steels: Microstructure and Properties, 3rd ed., Butterworth-Heinemann, Oxford, U.K., 2006 pp. 183-208.10.1016/B978-075068084-4/50011-X ↗