journal article·2023-10Open access

The Reliability of Single-Step and Double-Step Quench and Partitioning Heat Treatments on an AISI 420A Low Carbon Martensitic Stainless Steel

S. Barella, A. Gruttadauria, J. T. O. Menezes, E. M. Castrodeza, S. E. Quaini, C. Pelligra, E. A. McNally

Abstract

Abstract The microstructural and mechanical effects of various single-step (SS) and double-step (DS) quench and partition (Q&P) heat treatments applied to an AISI 420A low carbon martensitic stainless steel (MSS) has been studied. The goal with this work is to reach a total elongation (E pct) of 12 pct and an ultimate tensile strength (UTS) above 1200/1300 MPa, but ultimately to achieve a superior strength-ductility balance in comparison to its traditional Quench and Temper (Q&T) counterpart. This is being done by retaining austenite within the steel’s martensitic matrix at room temperature (RT) using novel SS and conventional DS Q&P heat treatments. Considerable work has been done to optimize DS Q&P heat treatments, but little has been done to understand the effects of removing a subsequent heating cycle through SS Q&P heat treatments has on MSSs. With that being said, partitioning is performed at the same quench interruption temperature for the SS Q&P heat treatments, and reheated to a higher temperature for the DS Q&P heat treatments. Experimental investigations were carried out on 1 mm thick, sheet samples to increase the number of potential applications for this steel and heat treatment. The microstructure of different SS and DS Q&P heat treatments was investigated through X-ray diffraction (XRD) and transmission electron microscopy (TEM) while mechanical property investigations were carried out using tensile and fracture toughness testing. DS Q&P heat treated samples quenched to 130 °C and partitioned for industrially relevant times of 10 and 30 minutes featured the highest values in terms of total elongation, tensile strength and fracture toughness. The SS Q&P heat treatments, on the other hand, were able to achieve improved mechanical properties to its Q&T counterpart. Overall, this work opens up the possibility of increased MSS usage for reliable, thin-walled component production with improved properties through Q&P heat treatment methods. The best results achieved in this study are a UTS of 1585 MPa, E pct of 22 pct, and a fracture toughness of 77 kJ/m2. Their lower total elongation of 9.6 pct is balanced by high tensile strength of 1812 MPa, ensuring higher toughness compared to traditional Q&T samples.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (61)

Show source-provided references
1. J.G. Speer, E. de Moor, and A.J. Clarke: Mater. Sci. Technol. (United Kingdom), 2015, vol. 31, pp. 3–9.10.1179/1743284714Y.0000000628 ↗
2. T. Wu, R. Wu, B. Liu, W. Liang, and D. Ke: Metals (Basel)., 2019, https://doi.org/10.3390/met9090958.10.3390/met9090958 ↗
3. J.G. Speer, E. De Moor, K.O. Findley, D.K. Matlock, B.C. De Cooman, and D.V. Edmonds: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 3591–3601.10.1007/s11661-011-0869-7 ↗
4. M. Frigo and S. Lindner: in Proceeding of Me-Mo, Metals for raod mobility, vol. 46, AIM, Bergamo, 2020, pp. 52–59.
5. H. Qu, G.M. Michal, and A.H. Heuer: Metall. Mater. Trans. A, 2014, vol. 45A, pp. 2741–49.10.1007/s11661-014-2232-2 ↗
6. X.D. Wang, Z.H. Guo, and Y.H. Rong: Mater. Sci. Eng. A, 2011, vol. 529, pp. 35–40.10.1016/j.msea.2011.08.050 ↗
7. R. Venturini, A. Bianchi, M. Andraghetti, C. Guarnaschelli, M.C. Cesile, and P.E. di Nunzio: La Metallurgia Italiana, 2020, vol. 46, pp. 43–51.
8. F. Tariq and R.A. Baloch: J. Mater. Eng. Perform., 2014, vol. 23, pp. 1726–39.10.1007/s11665-014-0902-2 ↗
9. G.E. Totten: Steel Heat Treatment: Metallurgy and Technologies, CRC Press, Boca Raton, 2006.10.1201/NOF0849384530 ↗
10. T. Tsuchiyama, J. Tobata, T. Tao, N. Nakada, and S. Takaki: Mater. Sci. Eng. A, 2012, vol. 532, pp. 585–92.10.1016/j.msea.2011.10.125 ↗
11. H. Kong, Q. Chao, B. Rolfe, and H. Beladi: Mater. Des., 2019, vol. 174, pp. 1–10.10.1016/j.matdes.2019.107799 ↗
12. J. Tobata, K.L. Ngo-Huynh, N. Nakada, T. Tsuchiyama, and S. Takaki: ISIJ Int., 2012, vol. 52, pp. 1377–82.10.2355/isijinternational.52.1377 ↗
13. J.G. Speer, F.C. Rizzo Assunção, D.K. Matlock, and Dv. Edmonds: Mater. Res., 2005, vol. 8, pp. 417–23.10.1590/S1516-14392005000400010 ↗
14. E.J. Seo, L. Cho, and B.C. de Cooman: Metall. Mater. Trans. A, 2016, vol. 47A, pp. 3797–3802.10.1007/s11661-016-3579-3 ↗
15. Y. Hui Guo, Z. Yong Fang, Z. Min Wang, B. Fu, and X. Tao Deng: J. Mater. Eng. Perform., 2019, vol. 28, pp. 3630–37.10.1007/s11665-019-04142-8 ↗
16. Y.F. Shen, X.X. Dong, X.T. Song, and N. Jia: Sci. Rep., 2019, vol. 9, pp. 1–9.10.1038/s41598-018-37186-2 ↗
17. M. Wendler, C. Ullrich, M. Hauser, L. Krüger, O. Volkova, A. Weiß, and J. Mola: Acta Mater., 2017, vol. 133, pp. 346–55.10.1016/j.actamat.2017.05.049 ↗
18. Q. Huang, C. Schröder, H. Biermann, O. Volkova, and J. Mola: Steel Res. Int., 2016, vol. 87, pp. 1082–94.10.1002/srin.201500472 ↗
19. A.R. Entwisle: Metall. Trans., 1971, vol. 2, pp. 2395–2407.10.1007/BF02814877 ↗
20. W. Steven: J. Iron Steel Inst., 1956, vol. 183, pp. 349–59.
21. K.W. Andrews: J. Iron Steel Inst., 1965, vol. 203, pp. 721–27.
22. M.J. Santofimia, L. Zhao, and J. Sietsma: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 3620–26.10.1007/s11661-011-0706-z ↗
23. A. Sierra-Soraluce, G. Li, M.J. Santofimia, J.M. Molina-Aldareguia, A. Smith, M. Muratori, and I. Sabirov: Mater. Sci. Eng. A, 2023, vol. 864, pp. 1–14.10.1016/j.msea.2022.144540 ↗
24. S.J. Lee, D.K. Matlock, and C.J. Van Tyne: Scr. Mater., 2011, vol. 64, pp. 805–08.10.1016/j.scriptamat.2011.01.001 ↗
25. T. Suzuki, Y. Ono, G. Miyamoto, and T. Furuhara: ISIJ J., 2010, vol. 50, pp. 1476–82.10.2355/isijinternational.50.1476 ↗
26. D.S. Codd: in SAE 2011 World Congress and Exhibition, 2011.
27. H. Chen, L. Zhao, S. Lu, Z. Lin, T. Wen, and Z. Chen: Metals (Basel), 2022, vol. 12, p. 12.
28. S. Kang, K. Kim, Y. Il Son, and S.J. Lee: ISIJ Int., 2016, vol. 56, pp. 2057–61.10.2355/isijinternational.ISIJINT-2016-257 ↗
29. A.A. Gorni: Steel Forming and Heat Treating Handbook, www.gorni.eng.br/e/Gorni_SFHTHandbook, 2019.
30. K. Harsha Vardhan, V. Shubhanyu, R. Kumar, and S. Abhishek: Int. J. Current Eng. Technol., 2017, vol. 7, pp. 1–4.
31. A. Hanumantharaju: KTH, 2017.
32. ASTM International: ASTM E975-13 Standard Practice for X-Ray Determination of Retained Austenite in Steel with Near Random Crystallographic Orientation.
33. D.V.S. Rao, K. Muraleedharan, and C.J. Humphreys: Microscopy, 2010, vol. 2, p. 1232.
34. ASTM E8M-Standard Test Methods for Tension Testing of Metallic Materials, ASM International, 2021.
35. ASTM E1820: Standard Test Method for Measurement of Fracture Toughness, ASTM international, 2020.
36. BS 8571:2018: Method of Test for Determination of Fracture Toughness in Metallic Materials Using Single Edge Notched Tension (SENT) Specimens, British Standards Institute, 2018.
37. S.J. Lee and K.S. Park: Metall. Mater. Trans. A, 2013, vol. 44, pp. 3423–27.10.1007/s11661-013-1798-4 ↗
38. C. García De Andrés, F.G. Caballero, C. Capdevila, and L.F. Álvarez: Mater. Charact., 2002, vol. 48, pp. 101–11.10.1016/S1044-5803(02)00259-0 ↗
39. A.N. Isfahany, H. Saghafian, and G. Borhani: J. Alloys Compd., 2011, vol. 509, pp. 3931–36.10.1016/j.jallcom.2010.12.174 ↗
40. Y.S. Choi, J.G. Kim, Y.S. Park, and J.Y. Park: Mater. Lett., 2007, vol. 61, pp. 244–47.10.1016/j.matlet.2006.04.041 ↗
41. Q. Huang, B.C. de Cooman, H. Biermann, and J. Mola: Metall. Mater. Trans. A, 2016, vol. 47A, pp. 1947–59.10.1007/s11661-016-3382-1 ↗
42. S. Dieck, P. Rosemann, A. Kromm, and T. Halle: IOP Conf. Ser., 2017, vol. 181, p. 12034.10.1088/1757-899X/181/1/012034 ↗
43. R.A. Stewart, J.G. Speer, B.G. Thomas, E. de Moor, and A.J. Clarke: Metall. Mater. Trans. A, 2019, vol. 50, pp. 4701–13.10.1007/s11661-019-05337-3 ↗
44. D.P. Koistinen and R.E. Marburger: Acta Metall., 1959, vol. 7, pp. 59–60.10.1016/0001-6160(59)90170-1 ↗
45. J. Mola and B.C. De Cooman: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 946–67.10.1007/s11661-012-1420-1 ↗
46. D.J. Dyson and B. Holmes: J. Iron Steel Inst., 1970, vol. 208, pp. 469–74.
47. P. Scherrer: Nachrichten von Der Gesellschaft Der Wissenschaften Zu Göttingen, Mathematisch-Physikalische Klasse, vol. 2, 1918.
48. S. Ebner, R. Schnitzer, E. Maawad, C. Suppan, and C. Hofer: Materialia (Oxf), 2021, vol. 15, pp. 1–10.
49. F.M. CastroCerda, E.I. Hernández, T. Ros-Yanez, and R.H. Petrov: Metall. Mater. Trans. A, 2020, vol. 51A, pp. 1506–18.10.1007/s11661-020-05643-1 ↗
50. S. Morito, Y. Adachi, and T. Ohba: Mater. Trans., 2009, vol. 50, pp. 1919–23.10.2320/matertrans.MRA2008409 ↗
51. S. Morito, H. Tanaka, R. Konishi, T. Furuhara, and T. Maki: Acta Mater., 2003, vol. 51, pp. 1789–99.10.1016/S1359-6454(02)00577-3 ↗
52. H.K. Yeddu: Comput. Mater. Sci., 2018, vol. 154, pp. 75–83.10.1016/j.commatsci.2018.07.040 ↗
53. E.A. Ariza, J. Poplawsky, W. Guo, K. Unocic, A.J. Ramirez, A.P. Tschiptschin, and S.S. Babu: Metall. Mater. Trans. A, 2018, vol. 49A, pp. 4809–23.10.1007/s11661-018-4743-8 ↗
54. L. Yuan: Rheinisch-Westfälischen Technischen Hochschule Aachen, 2012.
55. D. Salehiyan, J. Samei, B.S. Amirkhiz, L.G. Hector, and D.S. Wilkinson: Metall. Mater. Trans. A, 2020, vol. 51A, pp. 4524–39.10.1007/s11661-020-05882-2 ↗
56. R. Eckner, L. Krüger, C. Ullrich, M. Wendler, and O. Volkova: Int. J. Fract., 2019, vol. 215, pp. 139–51.10.1007/s10704-018-0332-5 ↗
57. E. de Moor, S. Lacroix, A.J. Clarke, J. Penning, and J.G. Speer: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 2586–95.10.1007/s11661-008-9609-z ↗
58. K.M.H. Bhadhon, J.R. Mcdermid, X. Wang, E.A. Mcnally, and F.E. Goodwin: in Proceeding of the 11th International Conference on Zinc and Zinc Alloy Coated Steel Sheet GALVATECH, Tokyo, 2017, pp. 1–8.
59. M. Takahashi: ISIJ Int., 2015, vol. 55, p. 55.
60. E.I. Hernandez-Duran, T. Ros-Yanez, F.M. Castro-Cerda, and R.H. Petrov: Mater. Sci. Eng. A, 2020, vol. 797, pp. 1–2.10.1016/j.msea.2020.140061 ↗
61. G. Prieto, W.R. Tuckart, and J.E.P. Ipiña: Materiali in Tehnologije, 2017, vol. 51, pp. 591–96.10.17222/mit.2016.126 ↗