The Effect of Strain Rate on the Tensile Deformation Behavior of Single Crystal, Ni-Based Superalloys
Source abstract
Abstract
Abstract Single crystal Nickel-based superalloys exhibit an anomalous yield point, the yield stress increasing with temperature to a maximum at around 750 ºC. Here, we demonstrate in the alloy CMSX-4 at 750 ºC that, although there is virtually no effect of strain rate on the initial yield point, at slow strain rates a second mechanism can initiate leading to a considerable softening effect. By examining the microstructures of a series of interrupted tests, this is attributed to the initiation of stacking fault shear after the operation of a secondary slip system. Using high-resolution TEM, the dislocation structures are shown to be identical in both structure and in the segregation of Co, Cr, and W, to those observed during creep deformation of single crystal alloys, although the conformation of the dislocations and faults differs from that observed during creep. This drop in flow stress at low strain rates is not observed in the alloys TMS138A and SRR99, in the former case, the improved creep resistance of this fourth-generation alloy would require a much slower strain rate to match the creep rate achievable at this temperature.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High Temperature Alloys and Creep · Nuclear Materials and Properties · Advanced Materials Characterization Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. D.M. Dimiduk: J. Phys. III, 1991, vol. 1(6), pp. 1025–53.
2. B. Kear and H. Wilsdorf: Trans. Am. Soc. Met., 1962, vol. 224, pp. 382–6.
3. D. Caillard: Mater. Sci. Eng. A, 2001, vol. 319, pp. 74–83.10.1016/S0921-5093(00)02017-7 ↗
4. M. Feller-Kniepmeier, T. Link, I. Poschmann, G. Scheunemann-Frerker, and C. Schulze: Acta Mater., 1996, vol. 44(6), pp. 2397–407.10.1016/1359-6454(95)00354-1 ↗
5. A. Sengupta, S. Putatunda, L. Bartosiewicz, J. Hangas, P. Nailos, M. Peputapeck, and F. Alberts: J. Mater. Eng. Perform., 1994, vol. 3(5), pp. 664–72.10.1007/BF02645265 ↗
6. M. McLean: Phil. Trans. Roy. Soc. Lond. A, 1995, vol. 351, pp. 419–33.10.1098/rsta.1995.0044 ↗
7. Z. Zhu, H. Basoalto, N. Warnken, and R.C. Reed: Acta Mater., 2012, vol. 60, pp. 4888–900. https://doi.org/10.1016/j.actamat.2012.05.0232.10.1016/j.actamat.2012.05.0232 ↗
8. L. Kovarik, R.R. Unocic, J. Li, P. Sarosi, and C. Shen: Progress Mater. Sci., 2009, vol. 54, pp. 839–73. https://doi.org/10.1016/j.pmatsci.2009.03.010.10.1016/j.pmatsci.2009.03.010 ↗
9. B.H. Kear and J.M. Oblak: Met. Trans., 1970, vol. 1, pp. 2477–86. https://doi.org/10.1007/BF03038373.10.1007/BF03038373 ↗
10. C.M.F. Rae and R.C. Reed: Acta Mater., 2007, vol. 55, pp. 1067–81.10.1016/j.actamat.2006.09.026 ↗
11. C. Cui, Y. Gu, Y. Yuan, and H. Harada: Scripta Mater., 2011, vol. 64, pp. 502–5.10.1016/j.scriptamat.2010.11.025 ↗
12. T.M. Smith, B.D. Esser, N. Antolin, A. Carlsson, R.E.A. Williams, A. Wessman, T. Hanlon, H.L. Fraser, W. Windl, D.W. McComb, and M.J. Mills: Nat. Commun., 2016, vol. 7, p. 3434. https://doi.org/10.1038/ncomms13434.10.1038/ncomms13434 ↗
13. T.M. Smith, R.R. Unocic, H. Deutchman, and M.J. Mills: Mater. High Temp., 2016, vol. 33, pp. 372–83. https://doi.org/10.1080/09603409.2016.1180858.10.1080/09603409.2016.1180858 ↗
14. A.C. Yeh, K. Kawagishi, H. Harada, T. Yokokawa, Y. Koizumi, T. Kobayashi, D. Ping, J. Fujioka, and T. Suzuki, in Proceedings of the International Symposium on Superalloys, 2008, pp. 619–28.10.7449/2008/Superalloys_2008_619_628 ↗
15. J. Li, Central symmetry parameter. http://mt.seas.upenn.edu/Archive/Graphics/A/Doc/CentralSymmetry.pdf. Part of AtomEye online manual (August 2003).
16. A.T. Jones and C. Baxter: Measur. Sci. Technol., 1995, vol. 6, pp. 131–33. https://doi.org/10.1088/0957-0233/6/1/021.10.1088/0957-0233/6/1/021 ↗
17. F. Smith: Industrial Applications of X-ray Diffraction, CRC Press, Boca Raton, 1999.10.1201/b16940 ↗
18. D. Crudden, A. Mottura, N. Warnken, B. Raeisinia, and R. Reed: Acta Mater., 2014, vol. 75, pp. 356–70. https://doi.org/10.1016/j.actamat.2014.04.075.10.1016/j.actamat.2014.04.075 ↗
19. T. Pollock and A. Argon: Acta Metall. Mater., 1992, vol. 40, pp. 1–30.10.1016/0956-7151(92)90195-K ↗
20. H.-J. Chang, M.C. Fivel, and J.-L. Strudel: Int. J. Plast, 2018, vol. 108, pp. 21–39. https://doi.org/10.1016/j.ijplas.2018.04.009.10.1016/j.ijplas.2018.04.009 ↗
21. G. Scheunemann-Frerker, H. Gabrisch, and M. Feller-Kniepmeier: Phil. Mag. A, 1992, vol. 65, pp. 1353–68. https://doi.org/10.1080/01418619208205609.10.1080/01418619208205609 ↗
22. M. Feller-Kniepmeier and G. Scheunemann-Frerker: Phil. Mag. A, 1990, vol. 62, pp. 77–88. https://doi.org/10.1080/01418619008244336.10.1080/01418619008244336 ↗
23. V.A. Vorontsov, L. Kovarik, M.J. Mills, and C.M.F. Rae: Acta Mater., 2012, vol. 60, pp. 4866–78. https://doi.org/10.1016/j.actamat.2012.05.014.10.1016/j.actamat.2012.05.014 ↗
24. V.A. Vorontsov, C. Shen, Y. Wang, D. Dye, and C.M.F. Rae: Acta Mater., 2010, vol. 58, pp. 4110–19. https://doi.org/10.1016/j.actamat.2010.03.041.10.1016/j.actamat.2010.03.041 ↗
25. B.H. Kear, A.F. Giamei, G.R. Leverant, and J.M. Oblak: Scr. Metall., 1969, vol. 3, pp. 123–29. https://doi.org/10.1016/0036-9748(69)90214-2.10.1016/0036-9748(69)90214-2 ↗
26. B.H. Kear, A.F. Giamei, G.R. Leverant, and J.M. Oblak: Scr. Metall., 1969, vol. 3, pp. 455–60. https://doi.org/10.1016/0036-9748(69)90130-6.10.1016/0036-9748(69)90130-6 ↗
27. G.R. Leverant and B.H. Kear: Metall. Mater. Trans. B., 1970, vol. 1B, pp. 491–98. https://doi.org/10.1007/BF02811560.10.1007/BF02811560 ↗
28. L. Kovarik, R. Unocic, J. Li, and M.J. Mills: JOM, 2009, vol. 61, pp. 42–48. https://doi.org/10.1007/s11837-009-0026-6.10.1007/s11837-009-0026-6 ↗
29. N. Eurich and P. Bristowe: Scripta Mater., 2015, vol. 102, pp. 87–90. https://doi.org/10.1016/j.scriptamat.2015.02.020.10.1016/j.scriptamat.2015.02.020 ↗
30. G. Viswanathan, R. Shi, A. Genc, V.A. Vorontsov, L. Kovarik, C.M.F. Rae, and M.J. Mills: Scripta Mater., 2015, vol. 94, pp. 5–8. https://doi.org/10.1016/j.scriptamat.2014.06.032.10.1016/j.scriptamat.2014.06.032 ↗
31. D. Barba, T.M. Smith, J. Miao, M.J. Mills, and R.C. Reed: Metall. Mater. Trans. A., 2018, vol. 49A, pp. 4173–85. https://doi.org/10.1007/s11661-018-4567-6.10.1007/s11661-018-4567-6 ↗
32. C.M.F. Rae, N. Matan, and R.C. Reed: Mater. Sci. Eng. A, 2001, vol. 300, pp. 125–34. https://doi.org/10.1016/S0921-5093(00)01788-3.10.1016/S0921-5093(00)01788-3 ↗
33. R.N. Jarrett and J.K. Tien: Metall. Trans. A, 1982, vol. 13, pp. 1021–32. https://doi.org/10.1007/BF02643399.10.1007/BF02643399 ↗
34. J.K. Tien and R.N. Jarrett, in Proceedings of a Conference Held in Liège, Belgium 4–6 October 1982, pp. 423–46. Springer. ISBN-10: 9027714681
35. A.A. Oni, S.R. Broderick, K. Rajan, and J.M. LeBeau: Intermetallics, 2016, vol. 73, pp. 72–78. https://doi.org/10.1016/j.intermet.2016.03.006.10.1016/j.intermet.2016.03.006 ↗
36. S.C.H. Llewelyn, K.A. Christofidou, V.J. Araullo-Peters, N.G. Jones, M.C. Hardy, E.A. Marquis, and H.J. Stone: Acta Mater., 2017, vol. 131, pp. 296–304. https://doi.org/10.1016/j.actamat.2017.03.067.10.1016/j.actamat.2017.03.067 ↗