Hybrid Laser-Arc Welding of 10-mm-Thick Cast Martensitic Stainless Steel CA6NM: As-Welded Microstructure and Mechanical Properties
Source abstract
Abstract
Cast CA6NM martensitic stainless steel plates, 10 mm in thickness, were welded using hybrid laser-arc welding. The effect of different welding speeds on the as-welded joint integrity was characterized in terms of the weld bead geometry, defects, microstructure, hardness, ultimate tensile strength, and impact energy. Significant defects such as porosity, root humping, underfill, and excessive penetration were observed at a low welding speed (0.5 m/min). However, the underfill depth and excessive penetration in the joints manufactured at welding speeds above 0.75 m/min met the specifications of ISO 12932. Characterization of the as-welded microstructure revealed untempered martensite and residual delta ferrite dispersed at prior-austenite grain boundaries in the fusion zone. In addition, four different heat-affected zones in the weldments were differentiated through hardness mapping and inference from the Fe-Cr-Ni ternary phase diagram. The tensile fracture occurred in the base metal for all the samples and fractographic analysis showed that the crack path is within the martensite matrix, along primary delta ferrite–martensite interfaces and within the primary delta ferrite. Additionally, Charpy impact testing demonstrated slightly higher fracture energy values and deeper dimples on the fracture surface of the welds manufactured at higher welding speeds due to grain refinement and/or lower porosity.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. X. Cao, P. Wanjara, J. Huang, C. Munro and A. Nolting: Mater. Design, 2011, vol. 32, pp. 3399-3413.10.1016/j.matdes.2011.02.002 ↗
2. C. Bagger, F.O. Olsen, J Laser Appl, 2005, 17, pp. 2-14.10.2351/1.1848532 ↗
3. F. Mirakhorli, X. Cao, X.T. Pham, P. Wanjara and J-L. Fihey: MS&T 2014 Conf. Pittsburgh, PA, 2014, pp. 1891–1900.
4. P. Bilmes, C. Llorente and M. Solari: 20th ASM Heat Treating Society Conf., St. Louis MO, 2000, pp. 556–65.
5. A.K. De, D.C. Murdock, M.C. Mataya, J.G. Speer and D.K. Matlock: Scripta Mater., vol. 50, 2004, pp. 1445-49.10.1016/j.scriptamat.2004.03.011 ↗
6. ASME Pressure Vessel code, Sec. IX: Welding and Brazing Qualifications, 2009.
7. ASME Pressure Vessel code. Sec. VIII., Div. 1, Rules for Construction of Pressure Vessels, 2009.
8. T. Ilar, I. Eriksson, J. Powell, A. Kaplan, Phys. Proc., 2012, vol. 39, pp. 27-32.10.1016/j.phpro.2012.10.010 ↗
9. ISO 12932: Laser-Arc Hybrid Welding of Steels, Nickel and Nickel Alloys—Quality Levels for Imperfections, 2013.
10. A. Kabir, X. Cao, M. Medraj, P. Wanjara, J. Cuddy and A. Birur: MS&T 2010 Conf., Houston, TX, 2010, pp. 2787–97.
11. X. Cao, W. Wallace, J.-P. Immarigeon and C. Poon: Mater. Manuf. Processes., 2003, vol. 18, pp. 23–49.10.1081/AMP-120017587 ↗
12. X. Cao, M. Jahazi, J.P. Immarigeon, and W. Wallace: J. Mater. Process. Technol., 2006, vol. 171, pp. 188-204.10.1016/j.jmatprotec.2005.06.068 ↗
13. N. Seto, S. Katayama and A. Matsunawa: Weld. Int., 2002, vol. 16, pp. 451-60.10.1080/09507110209549558 ↗
14. D. Abbott and C. Albright, J. Laser Appl., 2012, vol. 6, pp. 69-80.10.2351/1.4745339 ↗
15. E. Folkhard, G. Rabensteiner and E. Perteneder: Welding Metallurgy of Stainless Steels, Springer, Vienna, 1988, pp. 9–125.10.1007/978-3-7091-8965-8 ↗
16. D. Carrouge: PhD thesis, University of Cambridge, 2003.
17. J. Enerhaug and U. Steinsmo: Sci. Technol. Weld. Joining, 2001, vol. 6, pp. 330-38.10.1179/136217101101538866 ↗
18. D. Thibault, P. Bocher and M. Thomas: J. Mater. Process. Technol., 2009, vol. 209, pp. 2195-2202.10.1016/j.jmatprotec.2008.05.005 ↗
19. S. Sarafan, P. Wanjara, H. Champliaud and D. Thibault: Int. J. Adv. Manuf. Technol., vol. 78, 2015, pp. 1-13.10.1007/s00170-014-6713-7 ↗
20. H. Kitahara, R. Ueji, N. Tsuji and Y. Minamino: Acta Mater, 2006, vol. 54, pp. 1279-88.10.1016/j.actamat.2005.11.001 ↗
21. D. Carrouge, H. Bhadeshia and P. Woollin: Sci. Technol. Weld. Joining, 2004, vol. 9, pp. 377-89.10.1179/136217104225021823 ↗
22. Y.-K. Lee, H.-C. Shin, D.-S. Leem, J.-Y. Choi, W. Jin and C.-S. Choi: Mater. Sci. Technol., 2003, vol. 19, pp. 393-98.10.1179/026708303225009742 ↗
23. O. Akselsen, G. Rorvik, P. Kvaale and C. Van der Eijk: Weld. J., 2004, vol. 83, pp. 160-67.
24. S. Mrowec and S. Marcinkiewicz: Defects and Diffusion in Solids: An Introduction, Elsevier Amsterdam, 1980, pp. 174–300.
25. C. Garcia de Andres, G. Caruana and L. Alvarez: Mater. Sci. Eng. A., 1998, vol. 241, pp. 211-15.10.1016/S0921-5093(97)00491-7 ↗
26. D. Zou, Y. Han, W. Zhang and X. Fang: J. Iron Steel Res. Int., 2010, vol. 17, pp. 50-54.10.1016/S1006-706X(10)60128-8 ↗
27. J.C. Lippold and D.J. Kotecki: Welding Metallurgy and Weldability of Stainless Steels, Wiley, 2005, pp. 59–86.
28. A. Trudel, M. Sabourin and M. Brochu: Int. J. Fatigue, 2014, vol. 66, pp. 39-46.10.1016/j.ijfatigue.2014.03.006 ↗
29. K.Y. Benyounis, A.G. Olabi and M.S.J. Hashmi: J. Mater. Process. Technol., 2005 vol. 164, pp. 978-85.10.1016/j.jmatprotec.2005.02.060 ↗
30. Y. Song, X. Li, L. Rong, D. Ping, F. Yin, Y. Li, Materials Letters, 2010, vol. 64 1411-14.10.1016/j.matlet.2010.03.021 ↗
31. ASTM A 743/A 743M—03, Standard Specification for Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for General Application, 2003.
32. E.B. A. Akhiate, D. Thibault, and M. Brochu: COM 2014, Vancouver, BC, Canada, 2014.
33. G. Avramovic-Cingara, C.A. Saleh, M. Jain and D. Wilkinson: Metall. Mater. Trans. A, 2009, vol. 40, pp. 3117-27.10.1007/s11661-009-0030-z ↗
34. M. Azuma, X. Huang and G. Winther: PhD thesis, Technical University of Denmark, 2013.
35. L. Mathieu: ALSTOM Company, Sorel-Tracy, Quebec, private communication, 2014.
36. G.E. Dieter and D. Bacon: Mechanical Metallurgy, McGraw-Hill, New York, 1986, pp. 471–500.
37. M. McDonald and D. Ludwigson: J. Test. Eval., 1983, vol. 11, pp. 165-73.10.1520/JTE10677J ↗