Influence of the PM-Processing Route and Nitrogen Content on the Properties of Ni-Free Austenitic Stainless Steel
Source abstract
Abstract
Abstract Ni-free austenitic steels alloyed with Cr and Mn are an alternative to conventional Ni-containing steels. Nitrogen alloying of these steel grades is beneficial for several reasons such as increased strength and corrosion resistance. Low solubility in liquid and δ-ferrite restricts the maximal N-content that can be achieved via conventional metallurgy. Higher contents can be alloyed by powder-metallurgical (PM) production via gas–solid interaction. The performance of sintered parts is determined by appropriate sintering parameters. Three major PM-processing routes, hot isostatic pressing, supersolidus liquid phase sintering (SLPS), and solid-state sintering, were performed to study the influence of PM-processing route and N-content on densification, fracture, and mechanical properties. Sintering routes are designed with the assistance of thermodynamic calculations, differential thermal analysis, and residual gas analysis. Fracture surfaces were studied by X-ray photoelectron spectroscopy, secondary electron microscopy, and energy dispersive X-ray spectroscopy. Tensile tests and X-ray diffraction were performed to study mechanical properties and austenite stability. This study demonstrates that SLPS process reaches high densification of the high-Mn-containing powder material while the desired N-contents were successfully alloyed via gas–solid interaction. Produced specimens show tensile strengths >1000 MPa combined with strain to fracture of 60 pct and thus overcome the other tested production routes as well as conventional stainless austenitic or martensitic grades.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced materials and composites · Powder Metallurgy Techniques and Materials · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. International Stainless Steel Forum: Stainless Steel in Figures 2013, 2013.
2. H. Berns, W. Theisen: Eisenwerkstoffe: Stahl und Gusseisen, 4th ed, Springer, Berlin, 2008.
3. H. Hänninen, J. Romu, R. Ilola, J. Tervo, A. Laitinen: Journal of Materials Processing Technology, 2001, vol. 117 (3), pp. 424–30.10.1016/S0924-0136(01)00804-4 ↗
4. V. Gavriljuk, H. Berns, C. Escher, N. Glavatskaya, A. Sozinov, Y. Petrov: Materials Science and Engineering: A, 1999, vol. 271 (1-2), pp. 14–21.10.1016/S0921-5093(99)00272-5 ↗
5. T. Biggs and R.D. Knutsen: J. Phys. IV France, 1995, vol. 05 (C8), pp. 515–20.10.1051/jp4:1995879 ↗
6. L. Mújica Roncery: Doctoral Thesis, Bochum, Germany, 2010.
7. H. Berns, V.G Gavriljuk: KEM, 2007, vol. 345-346, pp. 421–24.10.4028/www.scientific.net/KEM.345-346.421 ↗
8. V. Gavriljuk, B. Shanina, H. Berns: Acta Materialia, 2000, vol. 48 (15), pp. 3879–93.10.1016/S1359-6454(00)00192-0 ↗
9. V.G Gavriliuk, B. Shanina, A. Tyshchenko, H. Berns, and S. Riedner: Proc. of 10th Int. Conf. High Nitrogen Steels (HNS 09).
10. V. Gavriljuk, B. Shanina, H. Berns: Acta Materialia, 2008, vol. 56 (18), pp. 5071–82.10.1016/j.actamat.2008.06.021 ↗
11. H. Berns, S. Riedner, A. Tyshchenko: MSF, 2007, vol. 539, pp. 4956–61.10.4028/www.scientific.net/MSF.539-543.4956 ↗
12. S. Riedner: Doctoral Thesis, Bochum, Germany, 2010.
13. V.G. Gavriliuk and H. Berns: High Interstitial Stainless Austenitic Steels, 2012.
14. [14] S. Riedner, H. Berns, A.I Tyshchenko, V.G Gavriljuk, C. Schulte‐Noelle, W. Trojahn: Mat.-wiss. u. Werkstofftech., 2008, vol. 39 (7), pp. 448–54.10.1002/mawe.200800272 ↗
15. H. Berns, V. Gavriljuk, B. Shanina: Adv. Eng. Mater, 2008, vol. 10, pp. 1083–93.10.1002/adem.200800214 ↗
16. S. Riedner, N. Nabiran, and H. Berns: Proc. 10th Int. Conf. High Nitrogen Steels (HNS 09), pp. 156–61.
17. H. Berns, S. Riedner, and V.G Gavriliuk: Proc. 10th Int. Conf. High Nitrogen Steels (HNS 09), pp. 140–49.
18. K. Zumsande, N. Krasokha, S. Huth, S. Weber, W. Theisen: J Mater Sci, 2012, vol. 47 (7), pp. 3214–26.10.1007/s10853-011-6159-3 ↗
19. P. Lindskog: Powder Metallurgy, 2004, vol. 47 (1), pp. 6–9.10.1179/pom.2004.47.1.6 ↗
20. W. Schatt, K.-P. Wieters, B. Kieback: Pulvermetallurgie: Technologien und Werkstoffe, 2nd ed, Springer, Berlin, 2007.10.1007/978-3-540-68112-0 ↗
21. R.M. German: Sintering Theory and Practice, Wiley, New York, 1996.
22. A. Weddeling, K. Zumsande, E. Hryha, S. Huth, and S. Weber: Proc. Euro PM2011 Congr Exhib., 2011, vol. 2, pp. 15–20.
23. K. Zumsande, A. Weddeling, E. Hryha, S. Huth, L. Nyborg, S. Weber, N. Krasokha, W. Theisen: Materials Characterization, 2012, vol. 71, pp. 66–76.10.1016/j.matchar.2012.06.002 ↗
24. E. Hryha and E. Dudrova: in Application of Thermodynamics to Biological and Materials Science, InTech, ed., pp. 573–602.
25. [25] H. Borgström, L. Nyborg: Powder Met, 2006, vol. 49 (1), pp. 48–56.10.1179/174329006X98353 ↗
26. D. Chasoglou, E. Hryha, L. Nyborg: Powder Metallurgy Progress, 2009, vol. 9 (3), pp. 141–55.
27. N. Krasokha: Dissertation, Bochum, Germany, 2012.
28. D. Chasoglou: Dissertation, Gothenburg, Sweden, 2012.
29. N. Chawla, X. Deng: Materials Science and Engineering: A, 2005, vol. 390 (1-2), pp. 98–112.10.1016/j.msea.2004.08.046 ↗
30. L. Čiripová, E. Hryha, E. Dudrová, A. Výrostková: Materials & Design, 2012, vol. 35, pp. 619–25.10.1016/j.matdes.2011.10.011 ↗
31. E. Dudrova, M. Kabátová: Powder Metallurgy Progress, 2002, vol. 8 (2), pp. 59–75.
32. R. Oro, M. Campos, E. Hryha, L. Nyborg, and J. Torralba: in Proc. Euro PM2011 Congr. Exhib. 2011, European Powder Metallurgy Association, ed., 2011, vol. 1, pp. 113–18.
33. F. Pöhl, S. Huth, W. Theisen: Journal of the Mechanics and Physics of Solids, 2014, vol. 66, pp. 32–41.10.1016/j.jmps.2014.02.002 ↗