journal article·2021-08Open access

Strength of 316L Stainless Steel Single-Lap Joints Brazed with Ni-Based Metallic Glass Foils for Corrosive Environments

David J. Kemmenoe, Eric A. Theisen, Shefford P. Baker

Abstract

In brazing, the choice of base metal, brazing filler metal (BFM), and braze process conditions involves complex tradeoffs among cost, mechanical strength, corrosion resistance, and others. In this work, the tradeoff between strength and corrosion resistance of 316L stainless steel joints brazed with a newer “very corrosion-resistant” Ni-Cr-P-Mo-Si BFM and a more established “corrosion-resistant” Ni-Cr-Si-B BFM is quantitatively analyzed. Corrosion tests and microstructural analyses were performed using common practices. Joint strength was evaluated by testing brazed single-lap joints (SLJs) in tension following standardized procedures. However, conventional interpretations were found to be inadequate for quantitative comparisons. Therefore, the SLJ stress state was analyzed in detail and a complete interpretation was developed. Joint strength is shown to be determined by the SLJ geometry, base metal properties, and braze microstructure. This analysis was used to explain the occurrence of different failure modes (fast fracture, peeling, and base metal failure) and to make suggestions for improved methods for conducting and analyzing brazed SLJ tensile tests. The newer BFM is shown to provide significantly better corrosion resistance for a moderate reduction in mechanical strength.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. American Welding Society 2007 Brazing Handbook 5 American Welding Society Miami, FL
2. RK Shah 2006 Heat Transf. Eng. 27 3 2210.1080/01457630600559462 ↗
3. A Rabinkin E Wenski A Ribaudo 1998 Weld. J. 77 66S 75S
4. A Rabinkin 2004 Sci. Technol. Weld. Join. 9 181 19910.1179/136217104225012300 ↗
5. H Li X Zhang O Mars X Zhao Q Lu Z Chen 2019 Weld. World 63 263 27510.1007/s40194-018-00687-9 ↗
6. NR Philips CG Levi AG Evans 2008 Metall. Mater. Trans. A 39A 142 14910.1007/s11661-007-9382-4 ↗
7. JP James F Bocher JR Scully 2009 Corrosion 65 511 52610.5006/1.3319155 ↗
8. E Lugscheider KD Partz 1983 Weld. J. 62 S160 S164
9. T. Hartmann and D. Nuetzel: in LÖT 9th International Conference of Brazing, High Temperature Brazing, and Diffusion Bonding, DVS 263, Aachen Germany, 2010, pp. 42–47.
10. DY Park SK Lee YJ Oh 2018 Metall. Mater. Trans. A 49A 4684 469910.1007/s11661-018-4811-0 ↗
11. T. Hartmann and M. Marsilius: in LÖT 11th International Conference of Brazing, High Temperature Brazing, and Diffusion Bonding, DVS 325, Aachen Germany, 2016, pp. 239–44.
12. T Tokunaga K Nishio M Hasebe 2001 J. Phase Equilib. 22 291 29910.1361/105497101770338798 ↗
13. American Welding Society 1963 AWS C3.1 Establishment of a Standard Test for Brazed Joints American Welding Society New York 1 61
14. American Welding Society 2019 AWS C3.2 Standard Method for Evaluating the Strength of Brazed Joints American Welding Society Miami, FL 1 17
15. FM Miller RL Peaslee 1958 Weld. J. 37 144S 150S
16. N Bredzs FM Miller 1968 Weld. J. 47 481S 496S
17. Y Flom L Wang 2004 Weld. J. 83 32S 38S
18. A Elrefaey W Tillmann 2007 Metall. Mater. Trans. A 38A 2956 296210.1007/s11661-007-9357-5 ↗
19. B Riggs A Benatar BT Alexandrov R Xu 2017 Weld. J. 96 421S 428S
20. V.R. Miller and W.L. Falke: RI 8783, Bureau of Mines, 1983.
21. RK Shiue SK Wu SY Chen 2003 Acta Mater. 51 1991 200410.1016/S1359-6454(02)00606-7 ↗
22. M Pouranvari A Ekrami AH Kokabi 2008 Mater. Sci. Eng. A 490 229 23410.1016/j.msea.2008.01.032 ↗
23. M Goland E Reissner 1944 J. Appl. Mech. 11 A17 2710.1115/1.4009336 ↗
24. M.D. Walsh, W. Bryzik, M.C. Young and C.O. Smith: Weld. J., 1971, pp. 39S–41S.
25. J Chen V Demers E Cadotte D Turner P Bocher 2017 J. Mater. Eng. Perform. 26 547 55310.1007/s11665-016-2491-8 ↗
26. B. Riggs: Ph.D. Thesis, Ohio State University, 2017.
27. AS McLaren I MacInnes 1958 Br. J. Appl. Phys. 9 72 7710.1088/0508-3443/9/2/306 ↗
28. E Sancaktar PO Lawry 1980 J. Adhes. 11 233 24110.1080/00218468008078919 ↗
29. E Lugscheider K Klohn R Lison 1979 Weld. J. 59 296S 300S
30. JPM Goncalves MFSF Moura de PMSF Castro de 2002 Int. J. Adhes. Adhes. 22 357 36510.1016/S0143-7496(02)00015-5 ↗
31. L. F. M. da Silva, P. J. C. das Neves, R. D. Adams and J. K. Spelt, Int. J. Adhes. Adhes., 2009, vol. 29, pp 319–330.10.1016/j.ijadhadh.2008.06.005 ↗
32. WC Oliver GM Pharr 1992 J. Mater. Res. 7 1564 158310.1557/JMR.1992.1564 ↗
33. RW Hertzberg 1983 Deformation and Fracture Mechanics of Engineering Materials 2 Wiley Hoboken
34. VO Volkersen 1938 Luftfahrtforschung 15 41 47
35. RD Adams NA Peppiatt 1973 J. Strain Anal. 8 134 13910.1243/03093247V082134 ↗
36. JA Harris RA Adams 1984 Int. J. Adhes. Adhes. 4 65 7810.1016/0143-7496(84)90103-9 ↗
37. EF Karachalios RD Adams LFM Silva da 2013 Int. J. Adhes. Adhes. 43 81 9510.1016/j.ijadhadh.2013.01.016 ↗
38. EF Karachalios RD Adams LFM Silva da 2013 Int. J. Adhes. Adhes. 43 96 10810.1016/j.ijadhadh.2013.01.017 ↗
39. ASTM 2016 ASTM D4896 ASTM West Conshohocken, PA 1 6
40. ST Smith JG Teng 2001 Eng. Struct. 23 857 87110.1016/S0141-0296(00)00090-0 ↗
41. IA Blech AA Levi 1981 J. Appl. Mech. 48 442 44510.1115/1.3157642 ↗
42. N Bredzs H Schwartzbart 1956 Weld. J. 35 610S 615S
43. HJ Saxton AJ West CR Barrett 1971 Metall. Trans. 2 999 100710.1007/BF02664231 ↗
44. AJ West HJ Saxton AS Tetelman CR Barrett 1971 Metall. Trans. 2 1009 101710.1007/BF02664232 ↗
45. M Finot YL Shen A Needleman S Suresh 1994 Metall. Mater. Trans. A 25A 2403 242010.1007/BF02648860 ↗
46. ASTM 2019 ASTM D3983 ASTM West Conshohocken, PA 1 11