Local Laser Heat Treatment in Dual-Phase Steels
Source abstract
Abstract
This research deals with processes leading to local strengthening effects in hot-rolled dual-phase (DP) steels. For this purpose, a method was investigated to achieve local strengthening, namely, local laser heat treatment (LHT). DP sheet steels were globally and homogenously deformed with different degrees of prestrains by cold rolling and subsequently locally heat treated by laser. Following this treatment with selected parameters, the microstructure of the surface and cross section of the heat-treated area as well as the mechanical properties were evaluated by light optical microscopy (LOM), scanning electron microscopy (SEM), as well as transmission electron microscopy (TEM), hardness measurement, and tensile testing. It can be stated that with partial heat treatment, local high strengthening can be produced. At lower heat treating temperatures, this effect could be attributed to bake hardening (BH). Increasing the prestrain as well as temperature results in improving the local properties. With increased heat treating temperature, the initial microstructure near the surface is affected. Partial strengthening of DP steels by laser can open up new fields of application for locally using the strengthening effect to only influence relevant areas of interest, thus providing the potential for saving energy and designed the component’s behavior.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Entropy Alloys Studies · Additive Manufacturing Materials and Processes · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. T.B. Hilditch, I.B. Timokhina, L.T. Robertson, E.V. Pereloma, and P.D. Hodgson: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 342–53.10.1007/s11661-008-9732-x ↗
2. S.K. Panda and Y. Zhou: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 1956–67.
3. R.H. Wagoner, J.H. Kim, and J.H. Sung: Mater. Forum Int., 2009, vol. 2, pp. 359–62.10.1007/s12289-009-0644-0 ↗
4. L.N. López de Lacalle, A. Lamikiz, J. Muñoa, M.A. Salgado, and J.A. Sánchez: Adv. Manufact. Technol. Int., 2005, vol. 29, pp. 49–63.10.1007/s00170-004-2482-z ↗
5. M. Steinhäusler: Diploma Thesis, University of Leoben, Leoben, Austria, 2004.
6. D. Wu and L. Zhuang: ISIJ Int., 2006, vol. 46, pp. 1059–66.10.2355/isijinternational.46.1059 ↗
7. T. Furukawa, M. Tanino, H. Morikawa, and M. Endo: Trans. ISIJ, 1984, vol. 24, pp. 113–21.10.2355/isijinternational1966.24.113 ↗
8. R.G. Davies: Metall. Mater. Trans. A, 1978, vol. 9A, pp. 41–52.10.1007/BF02647169 ↗
9. V. Colla, M. De Sanctis, A. Dimatteo, G. Lovicu, A. Solina, and R. Valentini: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 2557–67.10.1007/s11661-009-9975-1 ↗
10. D. Das and P.P. Chattopadhyay: Mater. Sci., 2009, vol. 44, pp. 2957–65.10.1007/s10853-009-3392-0 ↗
11. G.R. Speich and V.A. Demarest: Metall. Mater. Trans. A, 1981, vol. 12A, pp. 1419–28.10.1007/BF02643686 ↗
12. I.B. Timokhina, P.D. Hodgson, and E.V. Pereloma: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 2442–54.10.1007/s11661-007-9258-7 ↗
13. W.C. Jeong: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 463–67.10.1007/s11661-998-0126-x ↗
14. L. Samek, E. De Moor, J. Penning, J.G. Speer, and B.C. De Cooman: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 2542–54.10.1007/s11661-008-9605-3 ↗
15. M. Asadi and H. Palkowski: Steel Res. Int., 2009, vol. 7, pp. 499–506.
16. M. Asadi and H. Palkowski: Mater. Sci. Forum, 2010, vols. 638–642, pp. 3062–67.10.4028/www.scientific.net/MSF.638-642.3062 ↗
17. A.H. Cottrell and B.A. Bilby: Proc. Phys. Soc., 1949, vol. 62A, pp. 49–62.10.1088/0370-1298/62/1/308 ↗
18. R. Neugebauer, S. Scheffler, R. Poprawe, and A. Weisheit: Prod. Eng. Res. Devel., 2009, vol. 3, pp. 347–51.10.1007/s11740-009-0186-9 ↗
19. A. Kopel and W. Reitz: Advanced Materials Proc., ASM, Materials Park, OH, Oct. 1999.
20. J.M. Amado, C. Álvarez, and J.A. Pérez: Rev. Met. Madr., 2004, vol. 40, pp. 365–68.10.3989/revmetalm.2004.v40.i5.289 ↗
21. J.A. Pérez, J.L. Ocaña, and C. Molpeceres: Adv. Manufac. Technol., 2008, vol. 36, pp. 732–37.10.1007/s00170-006-0872-0 ↗
22. D. Hillebrand: Ph.D. Thesis, University of Bayreuth, Beyreuth, Germany, 2009.
23. M. Kikuchi, H. Hisada, Y. Kuroda, and K. Moritsu: Proc. 1st Int. Laser Conf. (ICALEO), Anaheim, CA, Laser Institute of America (LIA), Toledo, 1981.
24. T. Waterschoot, A.K. De, S. Vandeputte, and B.C. De Cooman: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 781–91.10.1007/s11661-003-0113-1 ↗
25. A.K. De, S. Vandeputte, and B.C. De Cooman: Scripta Mater., 2001, vol. 44, pp. 695–700.10.1016/S1359-6462(00)00638-2 ↗
26. R. Grange, R. Hribal, and L. Porter: Metall. Mater. Trans. A, 1977, vol. 8A, pp. 1775–85.10.1007/BF02646882 ↗
27. A. Aghajani, C. Somsen, and G. Eggler: Acta Mater., 2009, vol. 57, pp. 5093–5106.10.1016/j.actamat.2009.07.010 ↗
28. H.K.D.H. Bhadeshia and J.W. Christian: Metall. Mater. Trans. A, 1990, vol. 21A, pp. 767–97.10.1007/BF02656561 ↗
29. Y. Huanga, Y. Zhangb, H. Zhai, C. Zhou, and J. He: Mater. Sci. Forum, 2005, vols. 475–479, pp. 97–100.10.4028/www.scientific.net/MSF.475-479.97 ↗
30. C.H. Young and H.K.D.H. Bhadeshia: Mater. Sci. Technol., 1994, vol. 10, pp. 209–14.10.1179/mst.1994.10.3.209 ↗
31. R. Kaul, P. Ganesh, P. Tiwari, R.V. Nandedkar, and A.K. Nath: J. Mater. Process. Technol., 2005, vol. 167, pp. 83–90.10.1016/j.jmatprotec.2004.09.085 ↗
32. K. Obergfell, V. Schulze, and O. Vöhringer: Mater. Sci. Eng., 2003, vol. 355A, pp. 348–56.10.1016/S0921-5093(03)00099-6 ↗
33. H. Berns and W. Trojahn: in Creative Use of Bearing Steels, ASTM STP 1195, J.J. Hoo, ed., ASTM International, West Conshohocken, PA, 1993, pp. 149–55.10.1520/STP24831S ↗
34. N.J. Kim and G. Thomas: Metall. Mater. Trans. A, 1981, vol. 12A, pp. 483–89.10.1007/BF02648546 ↗
35. A. Ghosh, R. Shukla, S. Das, and S. Chatterjee: Steel Res. Int., 2006, vol. 77, pp. 276–83.10.1002/srin.200606386 ↗
36. P.J. Jacques, J. Ladrié RE, and F. Delannay: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 2759–68.10.1007/s11661-001-1027-4 ↗
37. S.T. Mandziej: Mater. Sci. Eng., 1993, vol. 164A, pp. 275–80.10.1016/0921-5093(93)90677-7 ↗
38. B.L. Bramfitt and J.G. Speer: Metall. Mater. Trans. A, 1990, vol. 21A, pp. 817–29.10.1007/BF02656565 ↗
39. S. Traint, A. Pichler, K. Spiradek-Hahn, P. Stiaszny, C. Krempaszky, and E. Werner: Steel Res. Int., 2005, vol. 76, pp. 539–44.10.1002/srin.200506051 ↗
40. H.K.D.H. Bhadeshia: Acta Metall., 1980, vol. 28, pp. 1103–14.10.1016/0001-6160(80)90093-0 ↗
41. D.Q. Bai, S. Yue, T.M. Maccagno, and J.J. Jonas: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 989–1001.10.1007/s11661-998-1008-y ↗
42. H.K.D.H. Bhadeshia: in Bainite in Steels, 2nd ed., Institute of Materials (IOM) Communications, London, 2001, pp. 19–62.
43. S.W. Thompson, D.J. Colvin, and G. Krauss: Metall. Mater. Trans. A, 1990, vol. 21A, pp. 1497–1507.
44. L.J. Baker, S.R. Daniel, and J.D. Parker: Mater. Sci. Technol., 2002, vol. 18, pp. 355–68.10.1179/026708302225002452 ↗
45. A.K. De, S. Vandeputte, and B.C. De Cooman: Scripta Mater., 1999, vol. 41, pp. 831–37.10.1016/S1359-6462(99)00232-8 ↗