Preparation of Fine-Grained W-Ni-Fe Alloys by Using W Nanopowders
Source abstract
Abstract
The present study utilized W nanopowders (prepared by a two-stage reduction process consisting of steps of carbothermic pre-reduction and hydrogen deep reduction) to produce fine-grained 90W-7Ni-3Fe and 93W-4.9Ni-2.1Fe alloys. The effects of sintering temperature [in a range of 1573 K to 1723 K (1300 °C to 1450 °C)] and time on the microstructure and mechanical properties of W-Ni-Fe alloys were studied in detail. The microstructures of the prepared alloys at 1573 K and 1673 K (1300 °C and 1400 °C) indicated that the grain sizes of W grains are 5 μm after sintering for > 60 minutes at 1723 K (1450 °C). The observation shows the as-sintered alloys with different holding times exhibit different fracture modes. With increasing holding time, the hardness of two alloys first increases and then decreases at the same sintering temperature. It is also concluded that the bending strength of alloys increases with the increase of sintering temperature. The maximum hardness of 381 and 393.6 HV was obtained after sintering at 1573 K (1300 °C) for 60 minutes for 90W-7Ni-3Fe and 93W-4.9Ni-2.1Fe alloys, respectively, while the highest bending strength of 1381.4 and 1278.8 MPa could be achieved at 1673 K (1400 °C) for 120 minutes. The excellent mechanical properties of W-Ni-Fe alloys could be attributed to the grain refinement strengthening.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Metal and Thin Film Mechanics · Fusion materials and technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (62)
Show source-provided references
1. [1] A. Bose, D. Sims and R.M. German: Metall. Trans. A, 1988, vol. 19, pp. 487-94.10.1007/BF02649263 ↗
2. [2] R.M. German, L.L. Bourguignon and B.H. Rabin: Powder Metall., 1992, vol. 5, pp. 3-13.
3. [3] E. Ariel, J. Barta and D. Brandon: Powder Metall., 1973, vol. 5, pp. 126-9.
4. U.R. Kiran, A. Panchal, M. Sankaranarayana, G.V.S. Rao and T.K. Nandy: Mater. Sci. Eng. A, 2015, vol. 640, pp. 82-90.10.1016/j.msea.2015.05.046 ↗
5. [5] A. Upadhyaya: Mater. Chem. Phys., 2001, vol. 67, pp. 101-10.10.1016/S0254-0584(00)00426-0 ↗
6. [6] S.J. Park, J.M. Martin, J.F. Guo, J.L. Johnson and R.M. German: Metall. Mater. Trans. A, 2006, vol. 37, pp. 3337-46.10.1007/BF02586168 ↗
7. [7] Gerlach U: Metall. Trans. A, 1986, vol. 17, pp. 435-42.10.1007/BF02643950 ↗
8. [8] X.Q. Li, K. Hu, S.G. Qu, L. Li and C. Yang: Mater. Sci. Eng. A, 2014, vol. 599, pp. 233-41.10.1016/j.msea.2014.01.089 ↗
9. [9] Y.Y. Li, K. Hu, X.Q. Li, X. Ai and S.G. Qu: Mater Sci Eng. A, 2013, vol. 573, pp. 245-52.10.1016/j.msea.2013.02.069 ↗
10. [10] D.P. Xiang, L. Ding, Y.Y. Li, X.Y. Chen and T.M. Zhang: Mater. Sci. Eng. A, 2013, vol. 578, pp. 18-23.10.1016/j.msea.2013.04.065 ↗
11. [11] D.P. Xiang, L. Ding, Y.Y. Li, G.B. Chen and Y.W. Zhao: J. Alloys. Compd., 2013, vol. 562, pp. 19-24.10.1016/j.jallcom.2013.02.014 ↗
12. [12] L. Ding, D.P. Xiang, Y.Y. Li, C. Li and J.B. Li: Int. J. Refract. Met. Hard Mater., 2012, vol. 33, pp. 65-9.10.1016/j.ijrmhm.2012.02.017 ↗
13. [13] K. Hu, X.Q. Li, S.G. Qu and Y.Y. Li: Metall. Mater. Trans. A, 2013, vol. 44, pp. 923-33.10.1007/s11661-012-1454-4 ↗
14. [14] X.Q. Li, H.W. Xin, K. Hu and Y.Y. Li: Nonferrous Met. Soc. China, 2010, vol. 20, pp. 443-9.10.1016/S1003-6326(09)60160-6 ↗
15. [15] K.H. Lee, S.I. Cha, H.J. Ryu, M.F. Dilmore and S.H. Hong: J. Alloys. Compd., 2007, vol. 434-435, pp. 433-6.10.1016/j.jallcom.2006.08.284 ↗
16. [16] C.L. Chen and Y.M. Dong: Mater. Sci. Eng. A, 2011, vol. 528, pp. 8374-80.10.1016/j.msea.2011.08.041 ↗
17. [17] J.L. Fan, X. Gong, B.Y. Huang, M. Song, T. Liu and J.M. Tian: J. Alloys. Compd., 2010, vol. 489, pp. 188-94.10.1016/j.jallcom.2009.09.050 ↗
18. [18] X. Gong, J.L. Fan, F. Ding, M. Song, B.Y. Huang and J.M. Tian: Mater. Sci. Eng. A, 2011, vol. 528, pp. 3646-52.10.1016/j.msea.2011.01.070 ↗
19. [19] O.K. Donaldson, K. Hattar, T. Kaub, G.B. Thompson and J.R. Trelewicz: J. Mater. Res., 2018, vol. 33, pp. 68-80.10.1557/jmr.2017.296 ↗
20. [20] W. Liu, Y. Ma and J. Zhang: Int. J. Refract. Met. Hard Mater., 2012, vol. 35, pp. 138-42.10.1016/j.ijrmhm.2012.05.004 ↗
21. [21] D.P. Xiang, L. Ding, Y.Y. Li, J.B. Li, X.Q. Li and C. Li: Mater. Sci. Eng. A, 2012, vol. 511, pp. 95-9.10.1016/j.msea.2012.04.099 ↗
22. [22] L. Ding, D.P. Xiang, Y.Y. Li, Y.W. Zhao and J.B. Li: Mater. Des., 2012, vol. 37, pp. 8-12.10.1016/j.matdes.2011.12.010 ↗
23. [23] D.W. Tang, S.L. Zou and L. Yan: Powder Metall., 2018, vol. 61, pp. 28-35.10.1080/00325899.2017.1376791 ↗
24. [24] D.S. Venables and M.E. Brown: Thermochim. Acta, 1996, vol. 285, pp. 361-82.10.1016/0040-6031(96)02951-6 ↗
25. [25] Y. Shen: J. Mater. Chem. A, 2015, vol. 3, pp. 13114-88.10.1039/C5TA01228G ↗
26. [26] G.D. Sun, K.F. Wang, C.M Song and G.H. Zhang: Int. J. Refract. Met. Hard Mater., 2019, vol. 78, pp. 100-6.10.1016/j.ijrmhm.2018.08.013 ↗
27. [27] C.M Song, G.H. Zhang and K.C. Chou: JOM, 2020, vol. 72, pp. 379-84.10.1007/s11837-019-03749-5 ↗
28. [28] Z.B. Li, G.H. Zhang and K.C. Chou: Pow. Tech, 2020, vol. 360, pp. 430-43.10.1016/j.powtec.2019.11.019 ↗
29. [29] B.H. Rabin, A. Bose and R.M. German: Int. J. Powder Metall., 1989, vol. 25, pp. 21-7.
30. A. Belhadjhamida and R.M. German: in Tungsten and Tungsten Alloys-Recent Advances, E.S. Crowson, ed., The Minerals, Metals & Materials Society, Warrendale, 1991, pp. 3–19.
31. [31] U.R. Kiran, S. Venkat, B. Rishikesh, V.K. Iyer, M. Sankaranarayana and T.K. Nandy: Mater. Sci. Eng. A, 2013, vol. 582, pp. 389-96.10.1016/j.msea.2013.06.041 ↗
32. [32] E. Lassner and W.D. Schubert, Tungsten: Properties, Chemistry, Technology of the Element, Alloys, and Chemical Compounds (New York: Kluwer Academic, 1999).10.1007/978-1-4615-4907-9 ↗
33. [33] C. Suryanarayana and M.G. Norton: X-ray Diffraction: A Practical Approach, Springer, New York, NY, 1998.10.1007/978-1-4899-0148-4 ↗
34. [34] Standard Test Methods for Determining Average Grain Size, ASTM Designation E112-96, ASTM, Philadelphia, PA, 1996, p. 16.
35. [35] C.L. Chen and C.L. Huang: Met. Mater. Int., 2013, vol. 19, pp. 1047-51.10.1007/s12540-013-5018-y ↗
36. [36] C.L. Chen and C.L. Huang: Intermetallics, 2014, vol. 41, pp. 10-5.10.1016/j.intermet.2013.04.014 ↗
37. [37] Z.Z. Fang, H.T. Wang and V. Kumar: Int. J. Refract. Met. Hard Mater., 2017, vol. 62, pp. 110-7.10.1016/j.ijrmhm.2016.09.004 ↗
38. [38] H.T. Wang and Z.Z. Fang: J. Am. Ceram. Soc., 2012, vol. 95, pp. 2458-64.10.1111/j.1551-2916.2012.05282.x ↗
39. [39] R. German: Thermodynamics of sintering, in Sintering of Advanced Materials, ed. by Z.Z. Fang (Woodhead Publishing, Cambridge, 2010), pp. 3-32.10.1533/9781845699949.1.3 ↗
40. [40] Z.Z. Fang and H.T. Wang: Sintering of ultrafine and nanosized particles, in Sintering of Advanced Materials, ed. by Z.Z. Fang (Woodhead Publishing, Oxford, 2010), pp. 434-73.10.1533/9781845699949.3.434 ↗
41. [41] G.D. Sun, G.H. Zhang and K.C. Chou: Int. J. Refract. Met. Hard Mater., 2019, vol. 84, pp. 105039.10.1016/j.ijrmhm.2019.105039 ↗
42. [42] W.S. Liu, Y.Z. Ma and Q.S. Cai: Mater. Sci. Appl., 2011, vol. 2, pp. 609-14.
43. [43] Y. Han, J. Fan, T. Liu, H. Cheng and J. Tian: Int. J. Refract. Met. Hard Mater., 2012, vol. 34, pp. 18-26.10.1016/j.ijrmhm.2012.02.014 ↗
44. [44] K. Hu, X.Q. Li, C. Yang and Y.Y. Li: Trans. Nonferrous Met. Soc. China, 2011, vol. 21, pp. 493-501.10.1016/S1003-6326(11)60742-5 ↗
45. [45] R.M. German, P. Suri and S.J. Park: J. Mater. Sci., 2009, vol. 44, pp. 1-39.10.1007/s10853-008-3008-0 ↗
46. [46] R.M. German and K.S. Churn: Metall. Trans. A, 1984, vol. 15, pp. 331-8.10.1007/BF02645119 ↗
47. [47] X. Gong, J.L. Fan and F. Ding: Mater. Sci. Eng. A, 2015, vol. 646, pp. 315-21.10.1016/j.msea.2015.08.079 ↗
48. [48] J.D. Clayton: Theor. Appl. Fract. Mech., 2006, vol. 45, pp. 163-85.10.1016/j.tafmec.2006.03.001 ↗
49. [49] J.L. Fan, T. Liu, H.C. Cheng and D.L. Wang: J. Mater. Process. Technol., 2008, vol. 208, pp. 463-9.10.1016/j.jmatprotec.2008.01.010 ↗
50. [50] J. Das, G. A. Rao, S.K. Pabi, M. Sankaranarayana and T.K. Nandy: Mater. Sci. Eng. A, 2014, vol. 613, pp. 48-59.10.1016/j.msea.2014.06.072 ↗
51. [51] J. Das, G.A. Rao and S.K. Pabi: Mater. Sci. Eng. A, 2010, vol. 527, pp. 7841-7.10.1016/j.msea.2010.08.071 ↗
52. [52] G. Prabhu, R. Arockia and T.K. Nandy: Int. J. Refract. Met. Hard Mater., 2019, vol. 82, pp. 31-42.10.1016/j.ijrmhm.2019.03.024 ↗
53. [53] F. Akhtar: Int. J. Refract. Met. Hard Mater., 2008, vol. 26, pp. 145-51.10.1016/j.ijrmhm.2007.05.011 ↗
54. [54] P. Lu and R.M. German: J. Mater. Sci., 2001, vol. 36, pp. 3385-94.10.1023/A:1017943524875 ↗
55. [55] E.O. Hall: Proc. Phys. Soc., 1951, vol. 64B, pp. 747.10.1088/0370-1301/64/9/303 ↗
56. G.D. White and W.E. Gurwell: in Advances in powder metallurgy, T.B. Gasbarre and W.F. Jandeska, eds., Metal Powder Industries Federation, Princeton, 1989, pp. 355–69.
57. [57] X. Gong, J.L. Fan, F. Ding, M. Song and B.Y. Huang: Int. J. Refract. Met. Hard Mater., 2012, vol. 30, pp. 71-7.10.1016/j.ijrmhm.2011.06.014 ↗
58. H. Hofmann and G. Petzow: in Modern Developments in Powder Metallurgy, H.H. Hausner, E. Aqua and C. Whitman, eds., Metal Powder Industries Federation, Princeton, 1985, pp. 7–31.
59. [59] R.M. German, A. Bose and S.S. Mani: Metall. Trans. A, 1992, vol. 23, pp. 211-9.10.1007/BF02660866 ↗
60. [60] N. Senthilnathan, A.R. Annamalai and G. Venkatachalam: Mater. Sci. Eng. A, 2018, vol. 710, pp. 66-73.10.1016/j.msea.2017.10.080 ↗
61. [61] L. Ding, D.P. Xiang, Y.L. Pan and Y.Y. Li: J. Alloys. Compd., 2017, vol. 712, pp. 593-8.10.1016/j.jallcom.2017.04.141 ↗
62. [62] A. Mondal, A. Upadhyaya and D. Agrawal: J. Alloys. Compd., 2011, vol. 509, pp. 301-10.10.1016/j.jallcom.2010.09.008 ↗