Effects of Crack Closure and Cyclic Deformation on Thermomechanical Fatigue Crack Growth of a Near α Titanium Alloy
Source abstract
Abstract
In this study, closure corrected in-phase (IP) and out-of-phase (OP) thermomechanical fatigue crack growth rates at two temperature intervals viz. 573 K to 723 K (300 °C to 450 °C) and 723 K to 873 K (450 °C to 600 °C) of Timetal 834 near α titanium alloy are presented. It is found that closure mechanisms significantly influence the stage I crack growth behavior. Surface roughness-induced crack closure (RICC) predominantly modifies the crack growth rate of near-threshold region at 573 K to 723 K (300 °C to 450 °C) test conditions. However, oxide-induced crack closure further strengthens RICC at 723 K to 873 K (450 °C to 600 °C) TMF loading. In stage II crack growth behavior, the alloy shows higher crack growth rates at 723 K to 873 K (450 °C to 600 °C) OP-TMF loading which is attributed to the combined effect of cyclic hardening occurring at the crack tip and weakening of interlamellar regions due to oxidation.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fatigue and fracture mechanics · High Temperature Alloys and Creep · Titanium Alloys Microstructure and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (61)
Show source-provided references
1. A. K. Koul and N. C. Bellinger: Int. J. Fatigue, 1990, vol. 12, pp. 379-387.10.1016/0142-1123(90)90002-V ↗
2. A. K. Koul and N. C. Bellinger and G. Gould: Int J Fatigue, 1990, vol. 12, pp. 388-396.10.1016/0142-1123(90)90003-W ↗
3. A. D. Boyed-Lee, G. F. Harrison, and M. B. Henderson: Int. J. Fatigue, 2001, vol. 23, pp. S11-S19.10.1016/S0142-1123(01)00116-5 ↗
4. C. Soares: Gas Turbines: A Handbook of Air, Land and Sea applications. Butterworth-Heinemann, New York, NY, 2008, pp. 679-71610.1016/B978-075067969-5.50024-7 ↗
5. M. P. Boyce: Gas Turbine Engineering Handbook. 4th edition. Butterworth-Heinemann, New York, NY, 2012, pp. 803– 883.10.1016/B978-0-12-383842-1.00021-4 ↗
6. J. Schijve: Eng. Frac. Mech., 1979, vol. 11, pp. 182-19610.1016/0013-7944(79)90040-7 ↗
7. A. Fatemi and L. Yang: Int. J. Fatigue, 1998, vol. 20, pp. 9-3410.1016/S0142-1123(97)00081-9 ↗
8. W. A. Curtin, V. S. Deshpande, A Needleman, E Van der Giessen, and M. Wallin: Int. J. Fatigue, 2010, vol. 32, pp. 1511-1520.10.1016/j.ijfatigue.2009.10.015 ↗
9. D.F. Neal: in Proc. Sixth World Conf. on Titanium, P. Lacombe, R. Tricot, and G. Bérange, eds., 1988, pp. 253–58.
10. W.J. Evans: in Proc. Eighth World Conf. on Titanium, P.A Blenkishop, W.J. Evans, and H.M. Flower, eds., Birmingham, UK, 1995, pp. 1065–74.
11. O. Schauerte, A. Gysler, and G. Lütjering: in Fatigue Behaviour of Titanium Alloys, R.R. Boyer, D. Eylon, and G. Lütjering, eds., The Minerals, Metals & Materials Society, 1999, pp. 191–202.
12. K. Prasad, S. Abhaya, G. Amardendra, V. Kumar, K. V. Rajulapati, and K. Bhanu Sankara Rao: Eng. Frac. Mech., 2013, vol. 102, pp. 194–20610.1016/j.engfracmech.2013.02.017 ↗
13. S. H. Spence, W. J. Evans, and N. Medwell: Int. J. Fatigue, 1997, vol. 19, pp. 33-4110.1016/S0142-1123(96)00048-5 ↗
14. A. L. Dowsen, A. C. Hollis, and C. J. Beevers: Int. J. Fatigue, 1992, vol. 14, 261-70.10.1016/0142-1123(92)90010-A ↗
15. V. Kumar and G. Nagalaxmi: DMRL Technical Report, DMRL TR 2005 371, 2005, pp. 36
16. G. Lütjering and J. C. Williams: Titanium, 2nd ed., Springer, New York, 2007, pp. 186
17. K. Prasad, P. S. Karamched, A. Bhattacharjee, V. Kumar, K. BhanuSankaraRao, and M. Sundararaman: Mater. Des., 2015, vol. 65, pp. 297-31110.1016/j.matdes.2014.09.006 ↗
18. K. Prasad and V. Kumar: Mater. Sci. Eng. A., 2011, vol. 528, pp. 6263-627010.1016/j.msea.2011.04.085 ↗
19. ASTM Standard E 647-13ae1, Standard Test Method for Measurement of Fatigue Crack Growth Rates, Annual Book of ASTM Standards, American Society of Testing and Materials, West Conshohocken, PA, vol. 03, 2013.
20. ASTM standard E 2368-10, Standard Practice for Strain Controlled Thermomechanical Testing, Annual Book of ASTM Standards, American Society of Testing and Materials, West Conshohocken, PA, vol. 03, 2010.
21. K. Prasad and S. V. Kamat: Mater. Sci. Eng. A., 2008, vol. 490, pp. 477-48010.1016/j.msea.2008.01.005 ↗
22. H. Yuan and D. Kalkhof: Int. J. Fracture, 1999, vol. 100, pp. 355-37710.1023/A:1018703011486 ↗
23. R.P. Wei and R.L. Brazil: in Fatigue Crack Growth Measurement and Data Analysis, S.J. Hudak, Jr., and R.J. Bucci, eds., ASTM STP 738, American Society for Testing and Materials, 1981, pp. 103–19.
24. P. Paris and F. Erdogan: J. Fluids Eng., 1963, vol. 85, pp. 528-533.
25. C. Bathias and R. M. Pelloux: Metall. Trans., 1973, vol. 4, pp.1265-127310.1007/BF02644521 ↗
26. J.A. Ruppen, C.L. Hoffmann, V.M. Radhakrishnan, and A.J. McEvily: in Fatigue, Environment and Temperature effects, J.J. Burke, and V. Weiss V, eds., New York, 1983, pp. 265–300.10.1007/978-1-4899-1736-2_15 ↗
27. J. E. King and P. J. Cotterill: Mater. Sci. Tech. 1990, vol. 6, pp. 19-3110.1179/mst.1990.6.1.19 ↗
28. R. Foerch, A. Madson, and H. Ghonem: Metall. Trans. A., 1993, vol. 24A, pp. 1321-133110.1007/BF02668200 ↗
29. C. Laird and G. C. Smith: Phil. Mag., 1962, vol. 7, pp. 847-85710.1080/14786436208212674 ↗
30. J.P. Bailon and S.D. Antolovich: in Fatigue Mechanisms: Advances in Quantitative Measurement of Physical Damage, ASTM STP 811, J. Lankford, D.L. Davidson, W.L. Morris, and R.P. Wei, eds., ASTM, Philadelphia, pp. 313–49.
31. A. Saxena and S. D. Antolovich: Metall. Trans. A., 1975, vol. 6A, pp. 1809-182810.1007/BF02642311 ↗
32. N. J. Marchand, R. M. Pelloux, and B. Ilschner: Eng. Frac. Mech., 1988, vol. 31, pp.535-55110.1016/0013-7944(88)90095-1 ↗
33. M. D. Halliday, and C. J. Beevers, J. Testing and Evaluation, 1981, vol. 9, pp. 195-201.10.1520/JTE11227J ↗
34. J.E. Allison: in Fracture Mechanics: Eighteenth Symposium, D.T. Read and R.P. Reed, eds., ASTM STP 945, American Society for Testing and Materials, Philadelphia, PA, 1988, pp. 913–33.10.1520/STP23283S ↗
35. S. Suresh: Fatigue of materials, 2nd edition, Cambridge University Press, Cambridge, 1998, pp. 483.10.1017/CBO9780511806575 ↗
36. R. O. Ritchie and S. Suresh: Metall. Trans. A., 1982, vol. 13A, pp. 937-4010.1007/BF02642409 ↗
37. S. Suresh: Metall. Trans. A., 1985, vol 16A, pp. 249-60.10.1007/BF02816051 ↗
38. M. H. Yoo: Metall. Trans. A., 1981, vol. 12A, pp. 409-18.10.1007/BF02648537 ↗
39. U. F. Kocks and D. G. Westlake: Trans. TMS-AIME, 1967, vol. 239, pp. 1107-09.
40. G. R. Yoder, L. A. Cooley, and T. W. Crooker: Metall. Trans. A., 1977, vol. 8A, pp. 1737-174310.1007/BF02646877 ↗
41. G. T. Gray, J. C. Williams, and A. W. Thompson: Metall. Trans. A., 1983, vol. 14A, pp. 421-433.10.1007/BF02644220 ↗
42. A. L. Pilchak, A. Bhattacharjee, A. H. Rosenberger, and J. C. Williams: Int. J. Fatigue, 2009, vol. 31, pp. 989-99410.1016/j.ijfatigue.2008.03.036 ↗
43. J.C. Chesnutt, J.C. Williams, and A.W. Thompson: in Fatigue 84, C.J. Beevers, ed., University of Birmingham, Birmingham, UK, 1984, pp. 341–50.
44. K. Minakawa and A. J. McEvily: Scripta Metall., 1981, vol. 15, pp.633-63610.1016/0036-9748(81)90041-7 ↗
45. G.P. Vander Velde and D.A Koss: in Fatigue 84, C.J. Beevers, ed., University of Birmingham, Birmingham, UK, 1984, pp. 411–21.
46. J. Lankford and D. L. Davidson: Metall. Trans. A., 1983, vol. 14A, pp. 1227–1230.10.1007/BF02670462 ↗
47. R. W. Neu and H. Sehitoglu: Metall. Trans. A., 1989, vol. 20A, pp. 1755-1767.10.1007/BF02663207 ↗
48. H. Mishra, P. Ghosal, T. K. Nandy, and P. K. Sagar: Mater. Sci. Eng. A, 2005, vol. 399A pp. 222-23110.1016/j.msea.2005.03.027 ↗
49. C. Leyens, M. Peters, and W.A. Kaysser, in: Proc. Eighth World Conf. on Titanium, P.A. Blenkishop, W.J. Evans, and H.M. Flower, eds., Birmingham, UK, 1995, pp. 1935–42.
50. R.P. Wei: Fracture Mechanics: Integration of Fracture Mechanics, Material Science, and Chemistry. Cambridge University Press, Cambridge, 2010, p. 50.10.1017/CBO9780511806865 ↗
51. D. Broek: Elementary Engineering Fracture Mechanics. 4th edition. Kluwer Academic Publishers, Amsterdam, 1986, p. 91.10.1007/978-94-009-4333-9 ↗
52. M. Klesnil and P. Lukas: in Proc. Second Int. Conf. on Fracture, E.H. Andrews, N.E. Frost, R.W. Nichols, E. Smith, and P.L. Pratt, eds., Chapman and Hall, London, 1969, p. 725.
53. H.W. Liu and N. Iino: in Proc. Second Int. Conf. on Fracture, E.H. Andrews, N.E. Frost, R.W. Nichols, E. Smith, and P.L. Pratt, eds., Chapman and Hall, London, 1969, p. 812.
54. S. D. Antolovich and R. W. Armstrong: Prog. Mater. Sci., 2014, vol. 59, pp. 1-160.10.1016/j.pmatsci.2013.06.001 ↗
55. K. Prasad, and V. K. Varma: Mater. Sci. Eng. A.,2008, vol. 486A, pp. 158-166.10.1016/j.msea.2007.09.020 ↗
56. K. Prasad, R. Sarkar, P. Ghosal, and V. K. Varma: Mater. Sci. Eng. A.,2008, vol. 494A, pp. 227-231.10.1016/j.msea.2008.04.025 ↗
57. K. Gopinath, A. K. Gogia, S. V. Kamat, R. Balamuralikrishnan, and U. Ramamurty: Acta. Mater., 2009, vol. 57, pp. 3450-3459.10.1016/j.actamat.2009.03.046 ↗
58. K. Bhanu Sankara Rao, H. Schiffers, H. Schuster, and H. Nickel: Metall. Trans. A., 1988, vol. 19A, pp. 359-371.
59. S. Graff, S. Forest, J.-L Strudel, C. Prioul, P. Pilvin, J.-L Bechade: Mater. Sci. Eng. A., 2004, vol. 387-389, pp. 181–85.10.1016/j.msea.2004.02.083 ↗
60. S. Graff, S. Forest, J.-L Strudel, C. Prioul, P. Pilvin, J.-L Bechade: Scripta Mater., 2005, vol. 52, pp. 1181–118610.1016/j.scriptamat.2005.02.007 ↗
61. B.S.S. ChandraRao, M. Srinivas, and S. V. Kamat: Metall. Mater. Trans., 2008, vol. 39A, pp. 1340–4910.1007/s11661-008-9516-3 ↗