journal article·2017-06Open access

Effect of Weld Schedule on the Residual Stress Distribution of Boron Steel Spot Welds

N. D. Raath, D. Norman, I. McGregor, R. Dashwood, D. J. Hughes

Abstract

Abstract Press-hardened boron steel has been utilized in anti-intrusion systems in automobiles, providing high strength and weight-saving potential through gage reduction. Boron steel spot welds exhibit a soft heat-affected zone which is surrounded by a hard nugget and outlying base material. This soft zone reduces the strength of the weld and makes it susceptible to failure. Additionally, different welding regimes lead to significantly different hardness distributions, making failure prediction difficult. Boron steel sheets, welded with fixed and adaptive schedules, were characterized. These are the first experimentally determined residual stress distributions for boron steel resistance spot welds which have been reported. Residual strains were measured using neutron diffraction, and the hardness distributions were measured on the same welds. Additionally, similar measurements were performed on spot welded DP600 steel as a reference material. A correspondence between residual stress and hardness profiles was observed for all welds. A significant difference in material properties was observed between the fixed schedule and adaptively welded boron steel samples, which could potentially lead to a difference in failure loads between the two boron steel welds.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. A. Bardelcik, M.J. Worswick, S. Winkler, and M.A. Wells, Int. J. Impact Eng., 2012. 50: pp 49-62.10.1016/j.ijimpeng.2012.06.007 ↗
2. D. Mohr and F. Ebnoether, Int. J. Solids Struct., 2009. 46: pp 3535-47.10.1016/j.ijsolstr.2009.05.011 ↗
3. M. Naderi, L. Durrenberger, A. Molinari, and W. Bleck, J. Mater. Sci. Eng. A, 2007. 478(1): pp 130-39.
4. M. Naderi, Saeed-Akbari A., and W. Bleck, J. Mater. Sci. Eng. A, 2007. 487: pp 445-45510.1016/j.msea.2007.10.057 ↗
5. M. Merklein and J. Lechler, J. Mater. Process. Technol., 2006. 177(1): pp 452-55.10.1016/j.jmatprotec.2006.03.233 ↗
6. R. Mohan Iyengar, B. Fedewa, Y.W. Wang, D.F. Maatz Jr., and R.L. Hughes: SAE Technical Paper, 2008. 2008-01-0857.
7. H. Karbasian and A.E. Tekkaya, J. Mater. Process. Technol., 2010. 210(15): pp 2103-18.10.1016/j.jmatprotec.2010.07.019 ↗
8. N.D. Raath: Ph.D. Thesis, University of Warwick, 2014.
9. Yu, Y., C. Wang, S. Chen, and Z. Lu, Adv. Mater. Res., 2011. 339: pp 375-78.10.4028/www.scientific.net/AMR.339.375 ↗
10. Choi, H.S., G.H. Park, W.S. Lim, and B.M. Kim, J. Mech. Sci. Technol., 2011. 25: pp 1543-50.10.1007/s12206-011-0408-x ↗
11. Kong, J.P., T.K. Han, K.G. Chin, B.G. Park, and C.Y. Kang, Mater. Des., 2013. 54(1): pp 598-609.
12. Lienert T, Siewert T, Babu S, Acoff V (2011) ASM Handbook Volume 6A Welding Fundamentals and Processes. ASM International, Russell10.31399/asm.hb.v06a.9781627081740 ↗
13. J. Larsson: in AWST-2011, 2011. Belik.
14. S. Sommer: LS Dyna forum, Ulm, 2012, vol. 1: pp 1–10.
15. Withers, P.J. and H.K.D.H. Bhadeshia, Mater. Sci. Technol., 2001. 17(4): pp 366-75.10.1179/026708301101510087 ↗
16. Hutchings MT, Withers PJ, Holden TM, Lorentzen T, Introduction to the characterization of residual stress by neutron diffraction. 2005, CRC Press, Boca Raton, pp 4-5.10.1201/9780203402818 ↗
17. J. Altenkirch: Ph.D. Thesis, University of Manchester, 2009.
18. Hughes, D.J., M.N. James, D.G. Hattingh, and P.J. Webster, J. Neutron Res. 2003. 11(4): pp 289-93.10.1080/10238160410001726765 ↗
19. Staron, P., M. Kocak, S. Williams, and A. Wescott, Phys. B 2004. 350(1): pp E491-E93.10.1016/j.physb.2004.03.128 ↗
20. Allen, A.J., M.T. Hutchings, C.G. Windsor, and C. Andeani, Adv. Phys., 1985. 34(4): pp 445-73.10.1080/00018738500101791 ↗
21. Hughes, D.J., E. Koukovini-Platia, and E.L. Heeley, Fusion Eng. Des., 2014. 89(1): pp 104-08.10.1016/j.fusengdes.2013.12.041 ↗
22. Florea, R.S., C.R. Hubbard, K.N. Solanki, D.J. Bammann, W.R. Whittington, and E.B. Marin, J. Mater. Process. Technol., 2012. 212(11): pp 2358-70.10.1016/j.jmatprotec.2012.06.024 ↗
23. Ji, C.W., I. Jo, H. Lee, I.D. Choi, Y. do Kim, and Y.D. Park, J. Mech. Sci. Technol., 2014. 28(11): pp 4761-69.10.1007/s12206-014-1043-0 ↗
24. Avramovic-Cingara, G., Y. Ososkov, M.K. Jain, and D.S. Wilkinson, Mater. Sci. Eng., 2009. 516(1): pp 7-16.10.1016/j.msea.2009.03.055 ↗
25. Matya, M. and X.Q. Gayden, Weld. J., 2005. 84(11): pp 172-82.
26. Matuschek Messtechnik GmbH, http://www.matuschek.de/index_en.htm. Accessed 29 July 2016.
27. ARO Technologies, http://www.arotechnologies.com/en-GB. Accessed 29 July 2016.
28. den Uijl, N., T. Okada, T. Moolevliet, A. Mennes, E. van den Aa, M. Uchihara, S. Smith, H. Nishibata, T. van der Veldt, and K. Fukui, Weld. World, 2012. 56(8): pp 51-63.10.1007/BF03321365 ↗
29. British Standards Institute: BS EN ISO 10447:2007. British Standards, 2007.
30. Hughes, D.J., G. Bruno, T. Pirling, and P.J. Withers, Neutron News, 2006. 17(3): pp 28-32.10.1080/10448630600837549 ↗
31. British Standards Institute: ISO/TS 21432:2005. British Standards, 2005.
32. Pirling, T., G. Bruno, and P.J. Withers, J. Mater. Sci. Eng. A, 2006. 437(1): pp 139-44.10.1016/j.msea.2006.04.083 ↗
33. LAMP, the Large Array Manipulation Program. http://www.ill.eu/data_treat/lamp/the-lamp-book/. Accessed 19 October 2016.
34. British Standards Institute: BS EN ISO 6507-1:1998. British Standards, 1998.
35. Krauss, G., Mater. Sci. Eng. A, 1999. 273(1): pp 40-57.10.1016/S0921-5093(99)00288-9 ↗
36. Raath, N.D., D.J. Hughes, D. Norman, I. McGregor, and R. Dashwood, Characterization of Minerals, Metals, and Materials. 2013, Wiley: San Antonio, pp 481-90.
37. SORPAS User Manual 7.0. 2007: SWANTEC Software and Engineering ApS.
38. Reed Hill, R.E. and R. Abbaschian, Physical metallurgy principles. 1973, Van Nostrand, NewYork. pp 733-39.
39. Filippone, R., J. Root, P. Jacques, and S. Yue, ISIJ, 2002. 42(3): pp 304-09.10.2355/isijinternational.42.304 ↗
40. Woo, W., V.T. Em, E.Y. Kim, S.H. Han, Y.S. Han, and S.H. Choi, Acta Mater., 2012. 60(20): pp 6972-81.10.1016/j.actamat.2012.08.054 ↗
41. Honeycombe, R.W.K. and H.K.D.H. Bhadeshia, Steels Microstructure and Properties. 2011, Butterworth-Heinemann, Oxford. pp 184-93.