Low-Temperature Densification Sintering and Properties of Monoclinic-SrAl2Si2O8 Ceramics
Source abstract
Abstract
The dense monoclinic-SrAl2Si2O8 ceramics have been prepared by a two-step sintering process at a sintering temperature of 1173 K (900 °C). Firstly, the pre-sintered monoclinic-SrAl2Si2O8 powders containing small SiO2·Al2O3 crystal phases were obtained by continuously sintering a powder mixture of SrCO3 and kaolin at 1223 K (950 °C) for 6 hours and 1673 K (1400 °C) for 4 hours, respectively. Subsequently, by the combination of the pre-sintered ceramic powders with the composite flux agents, which are composed of a SrO·3B2O3 flux agent and α-Al2O3, the low-temperature densification sintering of the monoclinic-SrAl2Si2O8 ceramics was accomplished at 1173 K (900 °C). The low-temperature sintering behavior and microstructure evolvement of the monoclinic-SrAl2Si2O8 ceramics have been investigated in terms of Al2O3 in addition to the composite flux agents. It shows that due to the low-meting characteristics, the SrO·3B2O3 flux agent can urge the dense microstructure formation of the monoclinic-SrAl2Si2O8 ceramics and the re-crystallization of the grains via a liquid-phase sintering. The introduction of α-Al2O3 to the SrO·3B2O3 flux agent can apparently lead to more dense microstructures for the monoclinic-SrAl2Si2O8 ceramics but also cause the re-precipitation of SiO2·Al2O3 compounds because of an excessive Al2O3 content in the SrO·3B2O3 flux agent.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Microwave Dielectric Ceramics Synthesis · Ferroelectric and Piezoelectric Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (16)
Show source-provided references
1. L.E. Khoong, Y.M. Tan, and Y.C. Lam: J. Eur. Ceram. Soc., 2010, vol. 30, pp. 1973-87.10.1016/j.jeurceramsoc.2010.03.011 ↗
2. K. Makarovic, A. Meden, M. Hrovat, J. Holc, A. Bencan, A. Dakskobler, and M. Kosec: J. Am. Ceram. Soc., 2012, vol. 95, pp. 760-7.10.1111/j.1551-2916.2011.05027.x ↗
3. L.A. Orlova, N.V. Popovich, N.E. Uvarova, A. Paleari, and P.D. Sarkisov: Ceram. Int., 2012, vol. 38, pp. 6629-34.10.1016/j.ceramint.2012.05.049 ↗
4. M.M. Krzmanc, M. Valant, and D. Suvorov: J. Eur. Ceram. Soc., 2007, vol. 27, pp. 1181-5.10.1016/j.jeurceramsoc.2006.05.017 ↗
5. D. Long-Gonzalez, J. Lopez-Cuevas, C.A. Gutierrez-Charria, P. Pena, C. Baudin, and X. Turrillas: Ceram. Int., 2010, vol. 36, pp. 661-72.10.1016/j.ceramint.2009.10.008 ↗
6. C.M. Lopez, J. Lopez-Cuevas, J.L. Rodriguez-Galicia, C.A. Gutierrez-Chavarria, and M.I. Pech-Canul: Bol. Soc. Esp. Ceram. Vidr., 2013, vol. 52, pp. 98-104.10.3989/cyv.132013 ↗
7. Y. Kobayashi and M. Inagaki: J. Eur. Ceram. Soc., 2004, vol. 24, pp. 399-404.10.1016/S0955-2219(03)00215-2 ↗
8. T. Matsumoto and Y. Goto: J. Ceram. Soc. Jpn., 2009, vol. 117, pp. 748-52.10.2109/jcersj2.117.748 ↗
9. S. Rajesh and H. Jantunen: Int. J. Appl.Ceram. Technol., 2012, vol. 9, pp. 52-9.10.1111/j.1744-7402.2011.02684.x ↗
10. R.E. Chinn, M.J. Haun, C.Y. Kim, and D.B. Price: J. Am. Ceram. Soc., 1998, vol. 81, pp. 2285-93.10.1111/j.1151-2916.1998.tb02623.x ↗
11. H. Witzmann and G. Herzog: Z. Phys. Chem., 1964, vol. 225, pp. 197-208.10.1515/zpch-1964-22520 ↗
12. C. Ferone, B. Liguori, A. Marocco, S. Anaclerio, M. Pansini, and C. Colella: Microporous Mesoporous Mater., 2010, vol. 34, pp. 65-71.10.1016/j.micromeso.2010.05.008 ↗
13. D.N. Yoon and W.J. Huppmann: Acta Metall., 1979, vol. 27, pp. 693-8.10.1016/0001-6160(79)90020-8 ↗
14. Z. Misirli, H. Erkalfa, and O.T. Ozkan: Ceram. Int., 1996, vol. 22, pp. 33-7.10.1016/0272-8842(95)00050-X ↗
15. P.J.M. Gielisse and W.R. Forster: Nature,1962, vol. 195, pp. 69-70.10.1038/195069a0 ↗
16. J.-S. Kim, M.-E. Song, M-R. Joung Choi, S. Nahm, S.-II Gu, J.-H. Paik, and B.-H. Choi: J. Eur. Ceram. Soc., 2010, vol. 30, pp. 375-9.10.1016/j.jeurceramsoc.2009.04.028 ↗