journal article·2022-02

The Effect of Cryogenic Mechanical Alloying and Milling Duration on Powder Particles’ Microstructure of an Oxide Dispersion Strengthened FeCrMnNiCo High-Entropy Alloy

Michael Mayer, Gerald Ressel, Jiri Svoboda

Publisher page

Abstract

Oxide dispersion strengthened materials are commonly used for high-temperature applications. Among other possibilities, these oxides are mostly introduced by mechanical alloying comprising cold welding and fracturing of powders by high-impact loads during milling. However, despite their outstanding high-temperature performance, these materials are still not established because of their laborious and thus expensive processing. Therefore, to improve mechanical alloying’s efficiency, the effect of lower milling temperatures is investigated on an oxide-dispersion strengthened high-entropy-alloy in the proposed study. To this end, prealloyed FeCrMnNiCo powders were milled together with yttria at cryogenic and room temperature by using a novel attritor cryomill. Powders milled at both temperatures were subsequently compared regarding their macroscopic morphology, amount and size distribution of detectable yttria as well as defect structure by means of high-resolution scanning electron microscopy and X-ray diffraction, respectively. Investigations showed a significant decrease of powder particle size and an insignificant influence on their aspect-ratio at cryogenic conditions. Furthermore, the phase fraction of detectable yttria got reduced by cryomilling, indicating increased dissolution or at least refinement. Additionally, a higher full width at half maximum accompanied by increased stacking fault probability of the fcc FeCrMnNiCo matrix gained by X-ray diffraction measurements suggests an improved milling efficiency during cryomilling intensified by higher defect density as well as strength of FeCrMnNiCo powders.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Entropy Alloys Studies · High-Temperature Coating Behaviors · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. Rolls-Royce: The Jet Engine, 5th ed. Rolls-Royce, London, 1996.
2. M.H. Tsai and J.W. Yeh: Mater. Res. Lett., 2014, vol. 2, pp. 107–23. https://doi.org/10.1080/21663831.2014.912690.10.1080/21663831.2014.912690 ↗
3. D.B. Miracle and O.N. Senkov: Acta Mater., 2017, vol. 122, pp. 448–511. https://doi.org/10.1016/j.actamat.2016.08.081.10.1016/j.actamat.2016.08.081 ↗
4. M. Naeem, H. He, S. Harjo, T. Kawasaki, F. Zhang, B. Wang, S. Lan, Z. Wu, Y. Wu, Z. Lu, C.T. Liu, and X.L. Wang: Scripta Mater., 2020, vol. 188, pp. 21–5. https://doi.org/10.1016/j.scriptamat.2020.07.004.10.1016/j.scriptamat.2020.07.004 ↗
5. S. Huang, W. Li, S. Lu, F. Tian, J. Shen, E. Holmström, and L. Vitos: Scripta Mater., 2015, vol. 108, pp. 44–7. https://doi.org/10.1016/j.scriptamat.2015.05.041.10.1016/j.scriptamat.2015.05.041 ↗
6. K.V.S. Thurston, A. Hohenwarter, G. Laplanche, E.P. George, B. Gludovatz, and R.O. Ritchie: Intermetallics., 2019, https://doi.org/10.1016/j.intermet.2019.04.012.10.1016/j.intermet.2019.04.012 ↗
7. G. Laplanche, A. Kostka, O.M. Horst, G. Eggeler, and E.P. George: Microstructure evolution and critical stress for twinning in the CrMnFeCoNi high-entropy alloy. Acta Mater., 2016, vol. 118, pp. 152–63. https://doi.org/10.1016/j.actamat.2016.07.038.10.1016/j.actamat.2016.07.038 ↗
8. F. Otto, A. Dlouhý, C. Somsen, H. Bei, G. Eggeler, and E.P. George: Acta Mater., 2013, vol. 61, pp. 5743–55. https://doi.org/10.1016/j.actamat.2013.06.018.10.1016/j.actamat.2013.06.018 ↗
9. Y.H. Wang, Z.F. Zhang, S.J. Sun, H.J. Yang, Y.Z. Tian, H.R. Lin, and X.G. Dong: Mater. Sci. Eng. A., 2017, vol. 712, pp. 603–7. https://doi.org/10.1016/j.msea.2017.12.022.10.1016/j.msea.2017.12.022 ↗
10. J.H. Kim, K.R. Lim, J.W. Won, Y.S. Na, and H.S. Kim: Mater. Sci. Eng. A., 2018, vol. 712, pp. 108–13. https://doi.org/10.1016/j.msea.2017.11.081.10.1016/j.msea.2017.11.081 ↗
11. N. Stepanov, M. Tikhonovsky, N. Yurchenko, D. Zyabkin, M. Klimova, S. Zherebtsov, A. Efimov, and G. Salishchev: Intermetallics., 2015, vol. 59, pp. 8–17. https://doi.org/10.1016/j.intermet.2014.12.004.10.1016/j.intermet.2014.12.004 ↗
12. O. Bouaziz: Scripta Mater., 2012, vol. 66, pp. 982–5. https://doi.org/10.1016/j.scriptamat.2011.11.029.10.1016/j.scriptamat.2011.11.029 ↗
13. F. Bergner, I. Hilger, J. Virta, J. Lagerbom, G. Gerbeth, S. Connolly, Z. Hong, P.S. Grant, and T. Weissgärber: Metall. Mater. Trans. A Phys. Metall. Mater. Sci., 2016, vol. 47A, pp. 5313–24. https://doi.org/10.1007/s11661-016-3616-2.10.1007/s11661-016-3616-2 ↗
14. B. Gwalani, R.M. Pohan, O.A. Waseem, T. Alam, S.H. Hong, H.J. Ryu, and R. Banerjee: Scripta Mater., 2019, vol. 162, pp. 477–81. https://doi.org/10.1016/j.scriptamat.2018.12.021.10.1016/j.scriptamat.2018.12.021 ↗
15. H. Hadraba, Z. Chlup, A. Dlouhy, F. Dobes, P. Roupcova, M. Vilemova, and J. Matejicek: Mater. Sci. Eng. A., 2017, vol. 689, pp. 252–6. https://doi.org/10.1016/j.msea.2017.02.068.10.1016/j.msea.2017.02.068 ↗
16. F. Dobeš, H. Hadraba, Z. Chlup, A. Dlouhý, M. Vilémová, and J. Matějíček: Mater. Sci. Eng. A., 2018, vol. 732, pp. 99–104. https://doi.org/10.1016/j.msea.2018.06.108.10.1016/j.msea.2018.06.108 ↗
17. S. Chung, B. Lee, S.Y. Lee, C. Do, and H.J. Ryu: J. Mater. Sci. Technol., 2021, vol. 85, pp. 62–75. https://doi.org/10.1016/j.jmst.2020.11.081.10.1016/j.jmst.2020.11.081 ↗
18. C. Suryanarayana: Mechanical Alloying and Milling, Marcel Dekker, New York, 2004.10.1201/9780203020647 ↗
19. D.B. Witkin and E.J. Lavernia: Prog. Mater. Sci., 2006, vol. 51, pp. 1–60. https://doi.org/10.1016/j.pmatsci.2005.04.004.10.1016/j.pmatsci.2005.04.004 ↗
20. H. Wen, T.D. Topping, D. Isheim, D.N. Seidman, and E.J. Lavernia: Acta Mater., 2013, vol. 61, pp. 2769–82. https://doi.org/10.1016/j.actamat.2012.09.036.10.1016/j.actamat.2012.09.036 ↗
21. M.K. Miller: Microsc. Res. Tech., 2006, vol. 69, pp. 359–65. https://doi.org/10.1002/jemt.20291.10.1002/jemt.20291 ↗
22. G. Ressel, D. Holec, A. Fian, F. Mendez-Martin, and H. Leitner: Appl. Phys. A Mater. Sci. Process., 2014, vol. 115, pp. 851–8. https://doi.org/10.1007/s00339-013-7877-y.10.1007/s00339-013-7877-y ↗
23. G. Ressel, P. Parz, S. Primig, H. Leitner, H. Clemens, and W. Puff: J. Appl. Phys., 2014, vol. 115, pp. 1–8. https://doi.org/10.1063/1.4869787.10.1063/1.4869787 ↗
24. M.J. Alinger, S.C. Glade, B.D. Wirth, G.R. Odette, T. Toyama, Y. Nagai, and M. Hasegawa: Mater. Sci. Eng. A., 2009, vol. 518, pp. 150–7. https://doi.org/10.1016/j.msea.2009.04.040.10.1016/j.msea.2009.04.040 ↗
25. N. Oono and S. Ukai: Mater. Trans., 2018, vol. 59, pp. 1651–8. https://doi.org/10.2320/matertrans.M2018110.10.2320/matertrans.M2018110 ↗
26. L.L. Hsiung, M.J. Fluss, S.J. Tumey, B.W. Choi, Y. Serruys, F. Willaime, and A. Kimura: Phys. Rev. B Condens. Matter Mater. Phys., 2010, vol. 82, pp. 1–13. https://doi.org/10.1103/PhysRevB.82.184103.10.1103/PhysRevB.82.184103 ↗
27. M.P. Phaniraj, D.I. Kim, J.H. Shim, and Y.W. Cho: Acta Mater., 2009, vol. 57, pp. 1856–64. https://doi.org/10.1016/j.actamat.2008.12.026.10.1016/j.actamat.2008.12.026 ↗
28. M. Kiritani, Y. Satoh, Y. Kizuka, K. Arakawai, Y. Ogasawara, S. Arai, and Y. Shimomura: Philos. Mag. Lett., 1999, vol. 79, pp. 797–804. https://doi.org/10.1080/095008399176616.10.1080/095008399176616 ↗
29. X.L. Wu, B. Li, and E. Ma: Phys. Lett., 2007, vol. 91, pp. 1–4. https://doi.org/10.1063/1.2794416.10.1063/1.2794416 ↗
30. L. Zhang, C. Lu, G. Michal, G. Deng, and K. Tieu: Scripta Mater., 2017, vol. 136, pp. 78–82. https://doi.org/10.1016/j.scriptamat.2017.04.019.10.1016/j.scriptamat.2017.04.019 ↗
31. S. Kojima, Y. Satoh, H. Taoka, I. Ishida, T. Yoshiie, M. Kiritani, and M. Kiritani: Philos. Mag. A Phys. Condens. Matter Struct. Defects Mech. Prop., 1989, vol. 59, pp. 519–32. https://doi.org/10.1080/01418618908229782.10.1080/01418618908229782 ↗
32. J. Schiotz, T. Leffers, and B.N. Singh: Philos. Mag. Lett., 2001, vol. 81, pp. 301–9. https://doi.org/10.1080/09500830110041657.10.1080/09500830110041657 ↗
33. J. Svoboda, W. Ecker, V.I. Razumovskiy, G.A. Zickler, and F.D. Fischer: Prog. Mater. Sci., 2019, https://doi.org/10.1016/j.pmatsci.2018.10.001.10.1016/j.pmatsci.2018.10.001 ↗
34. F.D. Fischer, J. Svoboda, and E. Kozeschnik: Model. Simul. Mater. Sci. Eng., 2013, https://doi.org/10.1088/0965-0393/21/2/025008.10.1088/0965-0393/21/2/025008 ↗
35. J.H. Kim and C.H. Park: J. Alloys Compd., 2014, vol. 585, pp. 69–74. https://doi.org/10.1016/j.jallcom.2013.09.085.10.1016/j.jallcom.2013.09.085 ↗
36. J.H. Kim, T.S. Byun, E. Shin, J.B. Seol, S. Young, and N.S. Reddy: J. Alloys Compd., 2015, vol. 651, pp. 363–74. https://doi.org/10.1016/j.jallcom.2015.08.100.10.1016/j.jallcom.2015.08.100 ↗
37. NIST: Line Position and Line Shape Standard for Powder Diffraction (Lanthanum Hexaboride Powder), Natl. Inst. Stand. Technol. US Dep. Commer. Gaithersburg, MD. (2015) 1–5. https://www-s.nist.gov/srmors/certificates/660C.pdf?CFID=35608137&CFTOKEN=7e602cd95cb32152-D56C3582-CDD9-D727-1A32D16FDB2CF208.
38. B.E. Warren: XProg. Met. Phys., 1959, vol. 8, pp. 147–202. https://doi.org/10.1016/0502-8205(59)90015-2.10.1016/0502-8205(59)90015-2 ↗
39. T. Ungár: Scripta Mater., 2004, vol. 51, pp. 777–81. https://doi.org/10.1016/j.scriptamat.2004.05.007.10.1016/j.scriptamat.2004.05.007 ↗
40. J. Zbiral: Metall. Mater. Trans. A., 1994, vol. 27A, pp. 1371–7.
41. D. Wimler, S. Kardos, J. Lindemann, H. Clemens, and S. Mayer: Prakt. Metallogr. Metallogr., 2018, vol. 55, pp. 620–36. https://doi.org/10.3139/147.110547.10.3139/147.110547 ↗
42. S. Vock, B. Klöden, A. Kirchner, T. Weißgärber, and B. Kieback: Prog. Addit. Manuf., 2019, vol. 4, pp. 383–97. https://doi.org/10.1007/s40964-019-00078-6.10.1007/s40964-019-00078-6 ↗
43. J. Zbiral: Charakterisierung von Verteilungs-, Legierungs und Homogenisierungsprozessen beim mechanischen Legieren, Technische Universität Wien, Vienna, 1990.
44. K.H. Chung, J. He, D.H. Shin, and J.M. Schoenung: Mater. Sci. Eng. A., 2003, vol. 356, pp. 23–31. https://doi.org/10.1016/S0921-5093(02)00833-X.10.1016/S0921-5093(02)00833-X ↗
45. M. Li, Y. Guo, H. Wang, J. Shan, and Y. Chang: Intermetallics., 2020, vol. 123, 106819. https://doi.org/10.1016/j.intermet.2020.106819.10.1016/j.intermet.2020.106819 ↗
46. Y. Guo, M. Li, C. Chen, P. Li, W. Li, Q. Ji, Y. Zhang, and Y. Chang: Intermetallics., 2020, vol. 117, 106674. https://doi.org/10.1016/j.intermet.2019.106674.10.1016/j.intermet.2019.106674 ↗
47. R.M. Pohan, B. Gwalani, J. Lee, T. Alam, J.Y. Hwang, H.J. Ryu, R. Banerjee, and S.H. Hong: Mater. Chem. Phys., 2018, vol. 210, pp. 62–70. https://doi.org/10.1016/j.matchemphys.2017.09.013.10.1016/j.matchemphys.2017.09.013 ↗
48. K.H. Chung, R. Rodriguez, E.J. Lavernia, and J. Lee: Metall. Mater. Trans. A Phys. Metall. Mater. Sci., 2002, vol. 33A, pp. 125–34. https://doi.org/10.1007/s11661-002-0011-y.10.1007/s11661-002-0011-y ↗
49. S.H. Joo, H. Kato, M.J. Jang, J. Moon, E.B. Kim, S.J. Hong, and H.S. Kim: J. Alloys Compd., 2017, vol. 698, pp. 591–604. https://doi.org/10.1016/j.jallcom.2016.12.010.10.1016/j.jallcom.2016.12.010 ↗