journal article·2023-05Open access

Effect of Part Thickness and Build Angle on the Microstructure, Surface Roughness, and Mechanical Properties of Additively Manufactured IN-939

A. Fardan, U. Klement, H. Brodin, E. Hryha

Abstract

Abstract Powder bed fusion-laser beam of metals (PBF-LB/M) has attracted significant interest due to the possibility of producing dedicated design features like thin-walled structures, even though their mechanical response and microstructure are not well understood. Hence, thin-walled IN-939 structures of different thicknesses (0.5, 1 and 2 mm) were manufactured at two build angles (90 and 45 deg) by PBF-LB/M. A preferred 〈100〉 crystallographic orientation was found along the build direction in all cases. The crystallographic texture intensity and surface roughness increased as the part thickness decreased for 90 deg and increased for 45 deg build angle. Reduction in wall thickness resulted in a decrease in the tensile properties, e.g., YS decreases by up to 33 pct and UTS decreases by up to 30 pct in comparison with the bulk specimen which had YS of 1051 ± 11 MPa and UTS of 1482 ± 9 MPa. Obtained results indicate that the apparent difference in tensile properties is primarily due to the overestimation of the load-bearing area. Two methods to estimate the accurate tensile properties based on roughness compensation are presented, using of which the corrected tensile performance of the thin-walled specimens was comparable with a standard tensile specimen.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · Additive Manufacturing and 3D Printing Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (44)

Show source-provided references
1. W.E. Frazier: J. Mater. Eng. Perform., 2014, vol. 23, pp. 1917–28.10.1007/s11665-014-0958-z ↗
2. Z. Wu, S.P. Narra, and A. Rollett: Int. J. Adv. Manuf. Technol., 2020, vol. 110, pp. 191–207.10.1007/s00170-020-05827-4 ↗
3. ISO/ASTM: ISO/ASTM 52911-1:2019, Additive Manufacturing – Design – Part 1: Laser-based Powder Bed Fusion of Metals, 2019.
4. A. Leicht, U. Klement, and E. Hryha: Mater. Charact., 2018, vol. 143, pp. 137–43.10.1016/j.matchar.2018.04.040 ↗
5. S.S. Babu, N. Raghavan, J. Raplee, S.J. Foster, C. Frederick, M. Haines, R. Dinwiddie, M.K. Kirka, A. Plotkowski, Y. Lee, and R.R. Dehoff: Metall. Mater. Trans. A, 2018, vol. 49A, pp. 3764–80.10.1007/s11661-018-4702-4 ↗
6. T. DebRoy, H.L. Wei, J.S. Zuback, T. Mukherjee, J.W. Elmer, J.O. Milewski, A.M. Beese, A. Wilson-Heid, A. De, and W. Zhang: Prog. Mater. Sci., 2018, vol. 92, pp. 112–224.10.1016/j.pmatsci.2017.10.001 ↗
7. S. Sanchez, P. Smith, Z. Xu, G. Gaspard, C.J. Hyde, W.W. Wits, I.A. Ashcroft, H. Chen, and A.T. Clare: Int. J. Mach. Tools Manuf., 2021, vol. 165, p. 103729.10.1016/j.ijmachtools.2021.103729 ↗
8. A. Bridges, J. Shingledecker, A. Torkaman, and L. Houck: Proc. ASME Turbo Expo, 2020, vol. 8, pp. 1–10.
9. T.B. Gibbons and R. Stickler: in High Temperature Alloys for Gas Turbines, R. Brunetaud, D. Coutsouradis, T.B. Gibbons, Y. Lindblom, D.B. Meadowcroft, and R. Stickler, eds., Springer Netherlands, Dordrecht, 1982, pp. 369–93.10.1007/978-94-009-7907-9_15 ↗
10. G. Wang: in Precision Forming Technology of Large Superalloy Castings for Aircraft Engines, B. Sun, J. Wang, and D. Shu, eds., Springer Singapore, Singapore, 2021, pp. 33–65.10.1007/978-981-33-6220-8_2 ↗
11. T.S. Piwonka: in Materials Selection and Design, G.E. Dieter, ed., vol. 20, ASM Handbook, 1997, pp. 723–29.
12. Electro Optical Systems GmbH - EOS Additive Manufacturing: EOS NickelAlloy IN939 (Material Data Sheet), 2021.
13. A. Leicht, C. Pauzon, M. Rashidi, U. Klement, L. Nyborg, and E. Hryha: Adv. Ind. Manuf. Eng., 2021, vol. 2, p. 100037.
14. X. Wang, J.A. Muñiz-Lerma, O. Sánchez-Mata, M. Attarian Shandiz, and M. Brochu: Mater. Sci. Eng. A, 2018, vol. 736, pp. 27–40.10.1016/j.msea.2018.08.069 ↗
15. X. Wang, J.A. Muñiz-Lerma, O. Sanchez-Mata, M. Attarian Shandiz, N. Brodusch, R. Gauvin, and M. Brochu: Scripta Mater., 2019, vol. 163, pp. 51–56.10.1016/j.scriptamat.2018.12.032 ↗
16. O. Sanchez-Mata, X. Wang, J.A. Muñiz-Lerma, S.E. Atabay, M. Attarian Shandiz, and M. Brochu: J. Alloys Compd., 2022, vol. 901, p. 163465.10.1016/j.jallcom.2021.163465 ↗
17. C.-H. Yu, R.L. Peng, M. Calmunger, V. Luzin, H. Brodin, and J. Moverare: in Superalloys 2020, S. Tin, M. Hardy, J. Clews, J. Cormier, Q. Feng, J. Marcin, C. O’Brien, and A. Suzuki, eds., Springer International Publishing, Cham, 2020, pp. 1003–13.
18. C.H. Yu, R.L. Peng, V. Luzin, M. Sprengel, M. Calmunger, J.E. Lundgren, H. Brodin, A. Kromm, and J. Moverare: Addit. Manuf., 2020, vol. 36, p. 101672.
19. F. Bachmann, R. Hielscher, and H. Schaeben: Solid State Phenom., 2010, vol. 160, pp. 294–306.10.4028/www.scientific.net/SSP.160.63 ↗
20. International Organisation for Standardization: ISO 25178-2:2012, Geometrical Product Specifications (GPS) — Surface Texture: Areal — Part 2: Terms, Definitions and Surface Texture Parameters, vol. 25178-2:20, 2012.
21. P. Kanagarajah, F. Brenne, T. Niendorf, and H.J. Maier: Mater. Sci. Eng. A, 2013, vol. 588, pp. 188–95.10.1016/j.msea.2013.09.025 ↗
22. D. Deng, R.L. Peng, H. Brodin, and J. Moverare: Mater. Sci. Eng. A, 2018, vol. 713, pp. 294–306.10.1016/j.msea.2017.12.043 ↗
23. S. Banoth, C.W. Li, Y. Hiratsuka, and K. Kakehi: Metals (Basel), 2020, vol. 10, pp. 1–16.10.3390/met10081016 ↗
24. Z. Chen, X. Wu, D. Tomus, and C.H.J. Davies: Addit. Manuf., 2018, vol. 21, pp. 91–103.
25. A.V. Gusarov and E.P. Kovalev: Phys. Rev. B, 2009, vol. 80, pp. 16–20.10.1103/PhysRevB.80.024202 ↗
26. M. Rombouts, L. Froyen, A.V. Gusarov, E.H. Bentefour, and C. Glorieux: J. Appl. Phys., 2005, vol. 97, p. 024905.10.1063/1.1832740 ↗
27. S.I. Shahabad, U. Ali, Z. Zhang, A. Keshavarzkermani, R. Esmaeilizadeh, A. Bonakdar, and E. Toyserkani: J. Manuf. Process., 2022, vol. 75, pp. 435–49.10.1016/j.jmapro.2022.01.029 ↗
28. P. Pant, F. Salvemini, S. Proper, V. Luzin, K. Simonsson, S. Sjöström, S. Hosseini, R. Lin Peng, and J. Moverare: Mater. Des., 2022, vol. 214, p. 110386.10.1016/j.matdes.2022.110386 ↗
29. A.S. Shaikh: Chalmers University of Technology, 2018.
30. F. Calignano: Virtual Phys. Prototyp., 2018, vol. 13, pp. 97–104.10.1080/17452759.2018.1426368 ↗
31. S. Rott, A. Ladewig, K. Friedberger, J. Casper, M. Full, and J.H. Schleifenbaum: Addit. Manuf., 2020, vol. 36, p. 101437.
32. J.C. Snyder and K.A. Thole: J. Manuf. Sci. Eng. Trans. ASME, 2020, vol. 142, p. 071003.10.1115/1.4046504 ↗
33. J. Karlsson, T. Horn, H. West, R. Aman, A. Snis, H. Engqvist, J. Lausmaa, and O. Harrysson: Addit. Manuf., 2016, vol. 12, pp. 45–50.
34. ISO/ASTM: ISO/ASTM DIS 52911-3 Additive Manufacturing — Design — Part 3: Electron Beam Powder Bed Fusion of Metals, 2019.
35. C.H. Yu, A. Leicht, R.L. Peng, and J. Moverare: Mater. Sci. Eng. A, 2021, vol. 821, p. 141598.10.1016/j.msea.2021.141598 ↗
36. O. Sanchez-Mata, X. Wang, J.A. Muñiz-Lerma, S.E. Atabay, M. Attarian Shandiz, and M. Brochu: J. Alloys Compd., 2021, vol. 865, p. 158868.10.1016/j.jallcom.2021.158868 ↗
37. J. Dzugan, M. Sei, R. Prochazka, M. Rund, P. Podany, P. Konopik, and J.J. Lewandowski: Addit. Manuf., 2018, vol. 143, pp. 94–109.
38. L. Yang and L. Lu: Scripta Mater., 2013, vol. 69, pp. 242–45.10.1016/j.scriptamat.2013.04.009 ↗
39. W.J. Yuan, Z.L. Zhang, Y.J. Su, L.J. Qiao, and W.Y. Chu: Mater. Sci. Eng. A, 2012, vol. 532, pp. 601–05.10.1016/j.msea.2011.11.021 ↗
40. A. Kohyama, K. Hamada, and H. Matsui: J. Nucl. Mater., 1991, vol. 179–181, pp. 417–20.
41. H. Liu, Y. Shen, J. Ma, P. Zheng, and L. Zhang: J. Mater. Eng. Perform., 2016, vol. 25, pp. 3599–3605.10.1007/s11665-016-2245-7 ↗
42. B.B. Liu, J.Q. Han, R. Zhao, W. Liu, and M. Wan: Nanomaterials, 2016, vol. 35, pp. 989–98.
43. L. Zhang, W. Harrison, M.A. Yar, S.G.R. Brown, and N.P. Lavery: J. Mater. Res. Technol., 2021, vol. 15, pp. 1830–43.10.1016/j.jmrt.2021.09.029 ↗
44. ISO: ISO 6892-1:2016, Metallic Materials — Tensile Testing — Part 1: Method of Test at Room Temperature, 2016.