Solid particle erosion of Al alloy and Al-alloy composites: Effect of heat treatment and angle of impingement
Source abstract
Abstract
Erosive wear behavior of the as-cast and heat-treated Al alloy and the Al-alloy-SiC particle composite against Al2O3 erodent has been examined at different angles of impingement (15 to 90 deg). It has been noted that the cast Al alloy exhibited a higher erosion rate than the heat-treated alloy and composites irrespective of the angle of impingement. It is noted that the as-cast and heat-treated Al alloy exhibited a maximum wear rate at the 45 deg angle of impingement, whereas the composite, in as-cast as well as in heat-treated conditions, showed a maximum erosion rate at the 60 deg angle of impingement. Subsurface studies of the alloy and composite confirm that the material loss, during erosive wear, is primarily due to microcutting/microplowing (i.e., abrasive-type) and microfracture (i.e., impact-type) actions. At a low angle of impingement, the abrasive type is the dominating factor for material removal, and at a higher angle of impingement, both the impact-type and abrasive-type actions play critical roles. The impact type is mainly localized at the tip of the erosion profile, while the abrasive type takes place along the sidewalls of the profile. This is explained on the basis of the erosion mechanism using a schematic diagram.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Erosion and Abrasive Machining · High-Temperature Coating Behaviors · Particle Dynamics in Fluid Flows
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. B.J. Briscone, M.J. Pickles, K.S. Julian, and M.J. Adams: Wear, 1995, vols. 181–183, pp. 759–65.10.1016/0043-1648(95)90192-2 ↗
2. A. Magnee: Wear, 1995, vols. 181–183, pp. 500–10.10.1016/0043-1648(94)07072-5 ↗
3. J. Qureshi, A. Levy, and B. Wang: J. Vac. Sci. Technol., 1986, vol. A4 (6), pp. 2638–47.10.1116/1.573696 ↗
4. Y. Akimune, T. Akiba, and T. Ogasawara: J. Mater. Sci., 1995, vol. 30, p. 1000.10.1007/BF01178436 ↗
5. H. Tsuruta, M. Masuda, T. Soma, and M. Matsui: J. Am. Ceram. Soc., 1990, vol. 73, p. 1714.10.1111/j.1151-2916.1990.tb09818.x ↗
6. A.A. Das, M.N. Yacoub, B. Zantout, and A.J. Clegg: Cast Met., 1988, vol. 1, p. 69.10.1080/09534962.1988.11818950 ↗
7. R. Molins, J.D. Barlout, and Y. Beinvenu: Mater. Sci. Eng. A, 1991, vol. 135, p. 111.10.1016/0921-5093(91)90546-Y ↗
8. E.D. Nussbaum: Light Met. Age, 1997, vol. 54, pp. 54–58.
9. K. Laden, J.D. Guerin, M. Watermer, and J.P. Bricout: Tribol. Lett., 2000, vol. 8, pp. 237–47.10.1023/A:1019159923619 ↗
10. M. Hunt: Mater. Eng., 1991, vol.108 (3), pp. 24–27.
11. Sreeram Srinivasan, R.O. Scattergood, and R. Warren: Mater. Trans. A, 1988, vol. 19A, pp. 1785–93.10.1007/BF02645147 ↗
12. S. Turenne, D. Simand, and M. Fiset: Wear, 1991, vol. 149, pp. 187–97.10.1016/0043-1648(91)90372-2 ↗
13. J.A. Bester and A. Ball: Wear, 1993, vols. 162–164, pp. 57–63.10.1016/0043-1648(93)90484-4 ↗
14. J.P. Tu, J. Pan, M. Matsumura, and H. Fukunaga: Wear, 1998, vol. 223, pp. 2–30.10.1016/S0043-1648(98)00295-6 ↗
15. M. Ramulu and S.P. Raju: Wear, 1993, vol. 166, pp. 55–63.10.1016/0043-1648(93)90279-U ↗
16. B.I. Levin, J.N. Dupont, and A.R. Marder: Wear, 2000, vol. 238, pp. 160–67.10.1016/S0043-1648(99)00363-4 ↗
17. R.A. Saravanan, M.K. Surappa, and B.N. Pramila Bai: Wear, 1997, vol. 202, pp. 154–64.10.1016/S0043-1648(96)07264-X ↗
18. K.C. Goretta, W. Wu, J.L. Routbort, and P.K. Rohatgi: Proc. Conf., Tribology of Composite Materials, Oak Ridge, TN, May 1–3, 1990, P.K. Rohatgi, C.S. Yust, and P.J. Blau, eds., ASM INTERNATIONAL, Materials Park, OH, 1990, pp. 147–55.
19. W. Wu, K.C. Goretta, and J.L. Routbort: Mater. Sci. Eng. A, 1992, vol. 151, pp. 85–95.10.1016/0921-5093(92)90185-4 ↗
20. S. Caron, P. Thiboult, S. Turenne, F.G. Hamel, and J. Masounave: Proc. Conf. Processing of Ceramic and Metal Matrix Composite, H. Mostaghact, ed., Halifax, NS, Canada, August 20–24, 1989, Pergomon Press, New York, NY, 1989, p. 424.10.1016/B978-0-08-037298-3.50044-X ↗
21. A. Wang and I.M. Hutching: in Metal and Ceramic Matrix Composites: Processing, Modeling and Mechanical Behaviour, R.B. Rhagat, A.H. Clauer, P. Kumar, and A.M. Ritter, eds., TMS, Warrendale, PA, 1990, pp. 499–508.
22. A.J. Ninham and A.V. Levy: Wear, 1988, vol. 121, pp. 347–61.10.1016/0043-1648(88)90210-4 ↗
23. Standard specification ASTM E-8-98: in Annual Book of ASTM standards, 1998, vol. 03.01, pp. 130-44.
24. Fuyan Lin and Hesheng Shao: Wear, 1991, vol. 141, pp. 279–89.10.1016/0043-1648(91)90274-X ↗
25. S. Das, D.P. Mondal, S. Sawla, and S. Dixit: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 3031–44.10.1007/s11661-002-0288-x ↗
26. S. Das, Jr.: Mater. Sci. Lett., 1997, vol. 16, pp. 1757–68.10.1023/A:1018579510067 ↗