Effect of Compositional Variation in TiO2-Based Flux-Cored Arc Welding Fluxes on the Thermo-physical Properties and Mechanical Behavior of a Weld Zone
Source abstract
Abstract
The effect of compositional variation in TiO2-based flux-cored arc welding fluxes on viscosity, wettability, and electronegativity was studied. The thermo-physical properties of the retrieved fluxes and their relationship with the mechanical properties of the weld zone, including tensile strength and micro-Vickers hardness, after welding were identified. Microstructural observation under similar welding conditions revealed significant grain coarsening at a corrected optical basicity (Λcorr) of 0.62, resulting in reduced strength and hardness due to greater heat transfer. Welding fluxes containing TiO2-based simple structural units should result in greater heat transfer due to the deficiency in complex [AlO4]5−- and [SiO4]4−-based structural units, as identified through spectroscopic analyses using fourier transform infrared spectroscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy. The electronegativity of the retrieved fluxes was also evaluated since higher electronegativity results in greater absorption of electrons in the arc, resulting in arc condensation towards the center direction. Consequently, deeper penetration could be obtained, where the highest electronegativity was identified to be approximately 0.62 of the corrected optical basicity. Thus, both the thermal conductivity and electronegativity of the welding fluxes were identified to determine the heat transfer phenomenon during flux-cored arc welding.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Metallurgical Processes and Thermodynamics · Engineering and Environmental Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (51)
Show source-provided references
1. J.E. Jin and Y.K. Lee: Mater. Sci. Eng. A, 2009, vol. 527, pp. 157-61.10.1016/j.msea.2009.08.028 ↗
2. M.H. Cai H. Ding, Z.Y. Tang, H.Y. Lee, and Y.K. Lee: Steel Res. Int., 2011, vol. 82, pp. 242-8.10.1002/srin.201000132 ↗
3. S. Kou: Welding Metallurgy, Wiley, Hoboken.
4. J.H.F. Gomes, S.C. Costa, A.P. Paiva, and P.P. Balestrassi: J. Mater. Eng. Perform., 2012, vol. 21, pp. 1862-72.10.1007/s11665-011-0103-1 ↗
5. J.E. Spear: Occup. Health Saf., 2011, vol. 80, pp. 64-5.
6. J.S. Kim, Y.K. Woo, and B.Y. Lee: Journal KWJS, 2012, vol. 30, pp. 304-8.
7. D.T. Cicic, G. Amza, C. Rontescu, S. Raise, and Z. Apostolescu: Global Journal Advances in Pure & Applied Sciences, 2013, vol.1, pp. 506-12.
8. K.H. Tseng, and K.L. Chen: J. Nanosci. Nanotech., vol. 12, pp. 6359–67.10.1166/jnn.2012.6419 ↗
9. G. Qin, G. Wang, and Z. Zou: Trans. Nonferrous Met. Soc. Cn., 2012, vol. 22, pp. 23-9.10.1016/S1003-6326(11)61134-5 ↗
10. D.D. Schwemmer, D.L. Olson and D.L. Williamson: Weld. J., 1979.vol. 58, p. 153.
11. S. Datta, A. Bandyopadhyay, and P.K. Pal: Int. J. Adv. Manuf. Technol., 2008, vol. 39, pp. 1136-4310.1007/s00170-007-1283-6 ↗
12. Standard, Standard Test Methods for Tension Testing of Metallic Materials, ASTM International, West Coshohocken, 2013.
13. C.S. Smith and L. Guttman: Trans. Aime., 1953, vol. 197, pp. 81-7.
14. K.C. Mills and S. Sridhar: Ironmaking Steelmaking, 1999, vol. 26, pp. 262-8.10.1179/030192399677121 ↗
15. S.H. Chung and I. Sohn: Int. J. Hydr. Energy., 2015, vol. 40, pp. 15893-900.10.1016/j.ijhydene.2015.08.083 ↗
16. K.H. Tseng and P.Y. Chen: Mater. Manuf. Processes, 2016, vol. 31, pp. 359-65.10.1080/10426914.2015.1058952 ↗
17. J.B. Kim and I. Sohn: J. NonCryst. Solids, 2013, vol. 379, pp. 235-4310.1016/j.jnoncrysol.2013.08.010 ↗
18. J.B. Kim, J.K. Choi, I.W. Han, and I. Sohn: J. NonCryst. Solids, 2016, vol. 432, pp. 218-26.10.1016/j.jnoncrysol.2015.10.009 ↗
19. R.E. Boni and G. Derge: JOM, 1956, vol. 8, pp. 53-9.10.1007/BF03377643 ↗
20. J.B. Kim and I. Sohn: ISIJ Int., 2014, vol. 54, pp. 2050-8.10.2355/isijinternational.54.2050 ↗
21. F. Khodabakhshi, M. Haghshenas, H. Eskandari, and B. Koohbor: Mater. Sci. Eng. A, 2015, vol. 636, pp. 331-9.10.1016/j.msea.2015.03.122 ↗
22. R. Schroeder, G. Hammes, C. Binder, and A.N. Klein: Mater. Res., 2011, vol. 14, pp. 564-8.10.1590/S1516-14392011005000082 ↗
23. A.K. De, D.C. Murdock, M.C. Mataya, J.G. Speer, and D.K. Matlock: Scr. Mater., 2004, vol. 50, pp. 1445-9.10.1016/j.scriptamat.2004.03.011 ↗
24. X.L. Wan, R. Wei, and K.M. Wu: Mater. Char., 2010, vol. 61, pp. 726-31.10.1016/j.matchar.2010.04.004 ↗
25. S.S. Babu: Curr. Opin. Solid State Mater. Sci., 2004, vol. 8, pp. 267-78.10.1016/j.cossms.2004.10.001 ↗
26. R.O. Scattergood and C.C. Koch: Scr. Metall. Mater., 1992, vol. 27, pp. 1195-200.10.1016/0956-716X(92)90598-9 ↗
27. P. Luo, D.T. McDonald, W. Xu, S. Palanisamy, M.S. Dargusch, and K. Xia: Scr. Mater., 2012, vol. 66, pp. 785-8.10.1016/j.scriptamat.2012.02.008 ↗
28. J.Y. Park and I. Sohn: Int. J. Heat Mass Tran., 2017, vol. 109, pp. 1014-25.10.1016/j.ijheatmasstransfer.2017.02.092 ↗
29. S.W. Park and I. Sohn: J. Am. Ceram. Soc., 2016, vol. 99, pp. 612-8.10.1111/jace.14013 ↗
30. A. Nagashima: Int. J. Thermophys., 1990, vol. 11, pp. 417-32.10.1007/BF01133571 ↗
31. K.C. Mills: ISIJ Int., 1993, vol. 33, pp. 148-55.10.2355/isijinternational.33.148 ↗
32. D.W. Lee and W.D. Kingery: J. Am. Ceram. Soc., 1960, vol. 43, pp. 594-607.10.1111/j.1151-2916.1960.tb13623.x ↗
33. M. Susa, A. Kushimoto, H. Toyota, M. Hayashi, R. Endo and Y. Kobayashi: ISIJ Int., 2009, vol. 49, pp. 1722-9.10.2355/isijinternational.49.1722 ↗
34. M. Susa, A. Kushimoto, R. Endo, and Y. Kobayashi: ISIJ Int., 2011, vol. 51, pp. 1587-96.10.2355/isijinternational.51.1587 ↗
35. M. Susa, S. Kubota, M. Hayashi, and K.C. Mills: Ironmaking Steelmaking, 2001, vol. 28, pp. 390-5.10.1179/irs.2001.28.5.390 ↗
36. S. Ozawa, M. Susa, T. Goto, R. Endo, and K.C. Mills: ISIJ Int., 2006, vol. 46, pp. 413-9.10.2355/isijinternational.46.413 ↗
37. M. Susa, F. Li, and K. Nagata: Metall. Trans. B, 1992, vol. 23, pp. 331-7.10.1007/BF02656289 ↗
38. E.J. Jung and D.J. Min: Steel Res. Int., 2012, vol. 83, pp. 705-11.10.1002/srin.201200023 ↗
39. D. Bonn, J. Eggers, J. Indekeu, J. Meunier, and E. Rolley: Rev. Mod. Phys., 2009, vol. 81, p. 739–805.10.1103/RevModPhys.81.739 ↗
40. I. Sohn and D.J. Min: Steel Res. Int., 2012, vol. 83, pp. 611-30.10.1002/srin.201200040 ↗
41. B. Reynard and S.L. Webb: Eur. J. Mineral., 1998, vol. 10, pp. 49-58.10.1127/ejm/10/1/0049 ↗
42. J.Y. Park, J.G. Park, C.H. Lee, and I. Sohn: ISIJ Int., 2011, vol. 51, pp. 889-94.10.2355/isijinternational.51.889 ↗
43. C. Le Losq, D.R. Neuville, P. Florian, G.S. Henderson, and D. Massiot: Geochim. Cosmochim. Acta, 2014, vol. 126, pp. 495-517.10.1016/j.gca.2013.11.010 ↗
44. N.J. Hess, Y. Su, and M.L. Balmer: J. Phys. Chem. B, 2001, vol. 105, pp. 6805-11.10.1021/jp010285h ↗
45. P. McMillan and B. Piriou: J. NonCryst. Solids, 1983, vol. 55, pp. 221-42.10.1016/0022-3093(83)90672-5 ↗
46. G.W. Toop and C.S. Samis: Trans. AIME 1962, vol. 224, p. 878-87.
47. R. Asokamani and R. Manjula: Phys. Rev. B, 1989, vol. 39, p. 4217–21.10.1103/PhysRevB.39.4217 ↗
48. L. Pauling: The Nature of the Chemical Bond and the Structure of Molecules and Crystals: an Introduction to Modern Structural Chemistry, Cornell University Press, Ithaca, NY, 1960.
49. Reddy R.R., Y. Nazeer Ahammed, P. Abdul Azeem, K. Rama Gopal, T.V.R. Rao: J. NonCryst. Solids, 2001, vol. 286, pp. 169–80.10.1016/S0022-3093(01)00481-1 ↗
50. P.J. Modenesi, E.R. Apolinário, and I.M. Pereira: J. Mater. Process. Technol., 2000, vol. 99, pp. 260-5.10.1016/S0924-0136(99)00435-5 ↗
51. K.H. Dhandha and V.J. Badheka: J. Manuf. Processes, 2015, vol. 17, pp. 48-57.10.1016/j.jmapro.2014.10.004 ↗