Semi-solid Constitutive Parameters and Failure Behavior of a Cast AA7050 Alloy
Source abstract
Abstract
AA7050 is an aluminum alloy with superior mechanical properties; however, it is prone to hot tearing (HT) during its production via direct-chill casting. This study focuses on extracting constitutive parameters of the alloy thermomechanical behavior in semi-solid state as well as gaining insight in its failure behavior. Tensile tests were performed using an Instron 5944 at solid fractions between 0.85 (550 °C) and 1.0 (465 °C), at deformation rates of 0.2 and 2 mm/min. The results showed that there are three mechanical behavior regimes in this solid fraction range: ductile at 1.0 (T = 465 °C) ≤ fs < 0.97 (T = 473 °C), brittle at 0.97 (T = 473 °C) ≤ fs ≤ 0.9 (T = 485 °C) and then ductile again (at 0.9 (T = 485 °C) < fs ≤ 0.85 (T = 550 °C)). Fracture surface analysis revealed that the fracture mode was mostly intergranular with fracture propagating through solid bridges as well. Semi-solid constitutive parameters were obtained by making a simple thermal model and numerical tensile tests in ALSIM software package and comparing the simulation results with experimental mechanical tests. The extracted constitutive parameters and available information from the literature support the fact that AA7050 is more susceptible to HT than AA5182 and Al-2 wt pct Cu alloys. The obtained parameters can further enhance the predictive capability of computer simulations of direct-chill casting.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. M. Dixit, R.S. Mishra, and K.K. Sankaran: Mater. Sci. Eng. A, 2008, vol. 478, pp. 163–72.10.1016/j.msea.2007.05.116 ↗
2. 2 E.A. Starke and J.T. Staley: Prog. Aerosp. Sci., 1996, vol. 32, pp. 131–72.10.1016/0376-0421(95)00004-6 ↗
3. D.A. Granger: Treatise Mater. Sci. Technol., vol. 31, 1989, pp. 109–35.10.1016/B978-0-12-341831-9.50009-7 ↗
4. 4 N.L. Loh and K.Y. Sia: J. Mater. Process. Technol., 1992, vol. 30, pp. 45–65.10.1016/0924-0136(92)90038-T ↗
5. 5 D.G. Eskin and L. Katgerman: Metall. Mater. Trans. A, 2007, vol. 38, pp. 1511–9.10.1007/s11661-007-9169-7 ↗
6. D.G. Eskin, A. Suyitno, and L. Katgerman: Prog. Mater. Sci., 2004, vol. 49, pp. 629–711.10.1016/S0079-6425(03)00037-9 ↗
7. 7 F. Sheykh-jaberi, S.L. Cockcroft, D.M. Maijer, and A.B. Phillion: J. Mater. Process. Technol., 2019, vol. 266, pp. 37–45.10.1016/j.jmatprotec.2018.10.029 ↗
8. 8 C. Puncreobutr, P.D. Lee, K.M. Kareh, T. Connolley, J.L. Fife, and A.B. Phillion: Acta Mater., 2014, vol. 68, pp. 42–51.10.1016/j.actamat.2014.01.007 ↗
9. Suyitno, V.I. Savran, L. Katgerman, and D.G. Eskin: Metall. Mater. Trans. A, 2004, vol. 35, pp. 3551–61.10.1007/s11661-004-0192-7 ↗
10. 10 D.G. Eskin and L. Katgerman: Mater. Sci. Forum, 2006, vol. 519–521, pp. 1681–6.10.4028/www.scientific.net/MSF.519-521.1681 ↗
11. 11 A. Stangeland, A. Mo, M. M’Hamdi, D. Viano, and C. Davidson: Metall. Mater. Trans. A, 2006, vol. 37, pp. 705–14.10.1007/s11661-006-0042-x ↗
12. 12 A. Stangeland, A. Mo, Ø. Nielsen, M. M’Hamdi, and D. Eskin: Metall. Mater. Trans. A, 2004, vol. 35, pp. 2903–15.10.1007/s11661-004-0238-x ↗
13. 13 L. Katgerman: JOM, 1982, vol. 34, pp. 46–9.10.1007/BF03339110 ↗
14. M. Lalpoor: Ph.D. Thesis, Delft University of Technology (TU Delft), The Netherlands, 2010.
15. 15 M. Lalpoor, D.G. Eskin, and L. Katgerman: Int. J. Mater. Res., 2011, vol. 102, pp. 1286–93.10.3139/146.110579 ↗
16. A. Suyitno, D.G. Eskin, and L. Katgerman: Key Eng. Mater., 2006, vol. 306–308, pp. 977–82.10.4028/www.scientific.net/KEM.306-308.977 ↗
17. 17 A. Stangeland, A. Mo, and D. Eskin: Metall. Mater. Trans. A, 2006, vol. 37, pp. 2219–29.10.1007/BF02586141 ↗
18. T.A.S. Subroto: Ph.D. Thesis, Delft University of Technology (TU Delft), The Netherlands, 2014.
19. 19 D.G. Eskin, V.I. Savran, and L. Katgerman: Metall. Mater. Trans. A, 2005, vol. 36, pp. 1965–76.10.1007/s11661-005-0059-6 ↗
20. T. Subroto, A. Miroux, D. Mortensen, M. M’Hamdi, D.G. Eskin, and L. Katgerman: IOP Conf. Ser. Mater. Sci. Eng., 2012, vol. 33, p. 012068.10.1088/1757-899X/33/1/012068 ↗
21. 21 M. M’Hamdi, A. Mo, and H.G. Fjær: Metall. Mater. Trans. A, 2006, vol. 37, pp. 3069–83.10.1007/s11661-006-0188-6 ↗
22. M. Lalpoor, D.G. Eskin, D. Ruvalcaba, H.G. Fjær, A. TenCate, N. Ontijt, and L. Katgerman: Mater. Sci. Eng. A, 2011, vol. 528, pp. 2831–42.10.1016/j.msea.2010.12.040 ↗
23. 23 M. Lalpoor, D.G. Eskin, and L. Katgerman: Metall. Mater. Trans. A, 2009, vol. 40, pp. 3304–13.10.1007/s11661-009-0031-y ↗
24. T. Subroto, A. Miroux, D.G. Eskin, and L. Katgerman: Mater. Sci. Eng. A, 2017, vol. 679, pp. 28–35.10.1016/j.msea.2016.10.021 ↗
25. 25 D.G. Eskin: Physical Metallurgy of Direct Chill Casting of Aluminum Alloys, CRC Press/Taylor & Francis, Boca Raton, FL, USA, 2008.10.1201/9781420062823 ↗
26. 26 E. Giraud, M. Suery, and M. Coret: Metall. Mater. Trans. A, 2010, vol. 41, pp. 2257–68.10.1007/s11661-010-0268-5 ↗
27. 27 W.M. van Haaften, B. Magnin, W.H. Kool, and L. Katgerman: Metall. Mater. Trans. A, 2002, vol. 33, pp. 1971–80.10.1007/s11661-002-0030-8 ↗
28. 28 O. Ludwig, J.-M. Drezet, C.L. Martin, and M. Suéry: Metall. Mater. Trans. A, 2005, vol. 36, pp. 1525–35.10.1007/s11661-005-0244-7 ↗
29. O. Ludwig, J.-M. Drezet, P. Ménésès, C.L. Martin, and M. Suéry: Mater. Sci. Eng. A, 2005, vol. 413–414, pp. 174–9.10.1016/j.msea.2005.09.087 ↗
30. 30 D. Fabrègue, A. Deschamps, M. Suéry, and W.J. Poole: Metall. Mater. Trans. A, 2006, vol. 37, pp. 1459–67.10.1007/s11661-006-0090-2 ↗
31. O. Ludwig, B. Commet, J.-M. Drezet, C.L. Martin, and M. Suery: in Proc. MCWASP X, 10th Int. Conf. on Modeling of Casting, Welding and Advanced Solidification Processes, TMS, Warrendale, PA, 2003, pp. 183–90.
32. 32 O. Ludwig, C.L. Martin, and M. Suéry: Mater. Forum, 2004, vol. 28, pp. 357–62.
33. C.L. Martin, M. Braccini, and M. Suéry: Mater. Sci. Eng. A, 2002, vol. 325, pp. 292–301.10.1016/S0921-5093(01)01528-3 ↗
34. C. Martin, O. Ludwig, and M. Suéry: in Proc. WCCM V, World Congr. on Computational Mechanics V, Vienna University of Technology, Vienna, 2002.
35. 35 H.G. Fjær and A. Mo: Metall. Trans. B, 1990, vol. 21, pp. 1049–61.10.1007/BF02670275 ↗
36. T. Subroto, A. Miroux, D.G. Eskin, K. Ellingsen, A. Marson, M. M’Hamdi, and L. Katgerman: in Proc. ICF13, 13th International Conf. on Fracture, Beijing, China, 2013, pp. 2528–36.
37. T.A.S. Subroto, A.G. Miroux, D.G. Eskin, and L. Katgerman: IOP Conf. Ser. Mater. Sci. Eng., 2011, vol. 27, p. 012074.10.1088/1757-899X/27/1/012074 ↗
38. A. Alankar and M.A. Wells: Mater. Sci. Eng. A, 2010, vol. 527, pp. 7812–20.10.1016/j.msea.2010.08.056 ↗
39. A.B. Phillion, S. Thompson, S.L. Cockcroft, and M.A. Wells: Mater. Sci. Eng. A, 2008, vol. 497, pp. 388–94.10.1016/j.msea.2008.07.027 ↗
40. 40 G. Chen, F. Lin, S. Yao, F. Han, B. Wei, and Y. Zhang: J. Alloys Compd., 2016, vol. 674, pp. 26–36.10.1016/j.jallcom.2016.02.254 ↗
41. 41 L. Sweet, M.A. Easton, J.A. Taylor, J.F. Grandfield, C.J. Davidson, L. Lu, M.J. Couper, and D.H. Stjohn: Metall. Mater. Trans. A, 2013, vol. 44, pp. 5396–407.10.1007/s11661-012-1562-1 ↗
42. 42 V. Mathier, P.-D. Grasso, and M. Rappaz: Metall. Mater. Trans. A, 2008, vol. 39, pp. 1399–409.10.1007/s11661-008-9529-y ↗
43. 43 I. Farup, J.-M. Drezet, and M. Rappaz: Acta Mater., 2001, vol. 49, pp. 1261–9.10.1016/S1359-6454(01)00013-1 ↗
44. M. Rappaz, J.-M. Drezet, P.-D. Grasso, and A. Jacot: in Proc. MCWASP X, 10th Int. Conf. on Modeling of Casting, Welding and Advanced Solidification Processes, TMS, Warrendale, PA, 2003, pp. 53–60.
45. 45 Y. Takayama, T. Tozawa, and H. Kato: Acta Mater., 1999, vol. 47, pp. 1263–70.10.1016/S1359-6454(98)00416-9 ↗
46. 46 D.C. Weckman and P. Niessen: Metall. Trans. B, 1982, vol. 13, pp. 593–602.10.1007/BF02650017 ↗
47. 47 M. Rappaz, J.-M. Drezet, and M. Gremaud: Metall. Mater. Trans. A, 1999, vol. 30, pp. 449–55.10.1007/s11661-999-0334-z ↗
48. 48 S. Mihanyar, A. Mo, M. M’Hamdi, and K. Ellingsen: Metall. Mater. Trans. A, 2011, vol. 42, pp. 1887–95.10.1007/s11661-010-0581-z ↗
49. 49 J.A. Spittle and A.A. Cushway: Met. Technol., 1983, vol. 10, pp. 6–13.10.1179/030716983803291226 ↗
50. 50 J. Campbell and T.W. Clyne: Cast Met., 1990, vol. 3, pp. 224–6.10.1080/09534962.1990.11819043 ↗
51. D.G. Eskin, L. Katgerman, A. Suyitno, and J.F. Mooney: Metall. Mater. Trans. A, 2004, vol. 35, pp. 1325–35.10.1007/s11661-004-0307-1 ↗
52. 52 D. Eskine, J. Zuidema, and L. Katgerman: Int. J. Cast Met. Res., 2002, vol. 14, pp. 217–23.10.1080/13640461.2002.11819440 ↗
53. L. Zhang, D.G. Eskin, M. Lalpoor, and L. Katgerman: Mater. Sci. Eng. A, 2010, vol. 527, pp. 3264–70.10.1016/j.msea.2010.02.005 ↗
54. 54 B. Magnin, L. Maenner, L. Katgerman, and S. Engler: Mater. Sci. Forum, 1996, vol. 217–222, pp. 1209–14.10.4028/www.scientific.net/MSF.217-222.1209 ↗