Effects of Mg Content on Characteristics of Nanoscale TiN Particles and Toughness of Heat-Affected Zones of Steel Plates After High-Heat-Input Welding
Source abstract
Abstract
The effect of Mg content on nanoscale particles and toughness in the heat-affected zone (HAZ) of steel plates after high-heat-input welding of 400 kJ cm−1 has been investigated through welding thermal simulation and nonaqueous electrolytic extraction. The results showed that most nanoscale particles were rectangular TiN particles with the sizes in the range of 50 to 300 nm. With increasing Mg content in steel from 0.0002 to 0.0044 wt pct, the number density and mean diameter of nanoscale TiN particles were increased from 0.38 to 5.11 × 108 mm−3 and decreased from 111 to < 75 nm, respectively. It was found that Mg deoxidation of molten steel was beneficial to the formation of fine TiN particles. Also, the HAZ toughness was improved by increasing the number of nanoscale TiN particles per unit volume. The improvement of HAZ toughness was attributed to the intensification of the pinning effect for retardation of the austenite grain growth by the incremental portion of fine TiN particles.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Welding Techniques and Residual Stresses · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. 1. J. Yang, K. Zhu, R.Z. Wang, Y. Zhang, and J.G. Shen: Baosteel Tech. Res., 2010, vol. 4, pp. 32-36.
2. 2. J. Yang, K. Zhu, R.Z. Wang, and J.G. Shen: Steel Res. Int., 2011, vol. 82, pp. 552-56.10.1002/srin.201100046 ↗
3. 3. L.Y. Xu, J. Yang, R.Z. Wang, Y.N. Wang, and W.L. Wang: Metall. Mater. Trans. A, 2016, vol. 47, pp. 3354-64.10.1007/s11661-016-3535-2 ↗
4. 4. L. P. Zhang, C. L. Davis, and M. Strangwood: Metall. Mater. Trans. A, 1999, vol. 30, pp. 2089-96.10.1007/s11661-999-0019-7 ↗
5. 5. M. Sennour, and C. Esnouf: Acta Mater., 2003, vol. 51, pp. 943-57.10.1016/S1359-6454(02)00498-6 ↗
6. 6. A. Karmakar, S. Kundu, S. Roy, S. Neogy, D. Srivastava, and D. Chakrabarti: Mater. Sci. Tech., 2014, vol. 30, pp. 653-64.10.1179/1743284713Y.0000000386 ↗
7. 7. S. Kanazawa, A. Nakashima, K. Okamoto, and K. Kanaya: Tetsu-to-Hagane, 1975, vol. 11, pp. 2589-603.10.2355/tetsutohagane1955.61.11_2589 ↗
8. 8. N. Fujiyama, T. Nishibata, A. Seki, H. Hirata, K. Kojima, and K. Ogawa: Sci. Technol. Adv. Mat., 2017, vol. 18, pp. 88-95.10.1080/14686996.2016.1244473 ↗
9. J. Moon, C. Lee, S. Uhm, and J. Lee: Acta Mater., 2006, vol. 54, pp. 1053-61.10.1016/j.actamat.2005.10.037 ↗
10. 10. S. Liu, and F.C. Liao: Mater. Sci. Eng. A, 1998, vol. 244, pp. 273-83.10.1016/S0921-5093(97)00550-9 ↗
11. 11. R. Staśko, H. Adrian, and A. Adrian: Mater. Charact., 2006, vol. 56, pp. 340-47.10.1016/j.matchar.2005.09.012 ↗
12. 12. Y. Zhang, X.B. Li, and H. Ma: Metall. Mater. Trans. B, 2016, vol. 47, pp. 2148-56.10.1007/s11663-015-0534-4 ↗
13. 13. W. Yan, Y.Y. Shan, and K. Yang: Metall. Mater. Trans. A, 2006, vol. 37, pp. 2147-58.10.1007/BF02586135 ↗
14. 14. J. Du, M. Strangwood, and C.L. Davis: J. Mater. Sci. Technol., 2012, vol. 28, pp. 878-88.10.1016/S1005-0302(12)60146-7 ↗
15. 15. T. Liu, M. Long, D. Chen, H. Duan, L. Gui, S. Yu, J. Cao, H. Chen, and H. Fan: J. Iron Steel Res. Int., 2018, vol. 25, pp. 1043-53.10.1007/s42243-018-0149-5 ↗
16. 16. S. Mukae, K. Nishio, and M. Katoh: Trans. Jpn Weld. Soc., 1987, vol. 18, pp. 148-58.
17. 17. A. Ghosh, A. Ray, D. Chakrabarti, and C.L. Davis: Mater. Sci. Eng. A, 2013, vol. 561, pp. 126-35.10.1016/j.msea.2012.11.019 ↗
18. 18. M.A. Linaza, J.L. Romero, J.M. Rodríguez-Ibabe, and J.J. Urcola: Scripta Metallurgica et Materialia, 1993, vol. 29, pp. 451-56.10.1016/0956-716X(93)90146-J ↗
19. 19. T. Kato, S. Sato, H. Ohta, and T. Shiwaku: Kobe Steel Eng. Rep., 2011, vol. 61, pp. 32-35.
20. 20. K. Zhu, and Z.G. Yang: Metall. Mater. Trans. A, 2011, vol. 42, pp. 2207-13.10.1007/s11661-011-0647-6 ↗
21. 21. D.P. Fairchild, D.G. Howden, and W.A. T. Clark: Metall. Mater. Trans. A, 2000, vol. 31, pp. 641-52.10.1007/s11661-000-0007-4 ↗
22. 22. L.P. Zhang, C.L. Davis, and M. Strangwood: Metallurgical and Materials Transactions A, 2001, vol. 32, pp. 1147-55.10.1007/s11661-001-0125-7 ↗
23. A. Kojima, A. Kiyose, R. Uemori, M. Minagawa, M. Hoshino, T. Nakashima, K. Ishida, and H. Yasui: Nippon Steel Tech. Rep. 90: 2–6 (2004)
24. 24. J. Yang, K. Zhu, R.Z. Wang, and J.G. Shen: Journal of Iron and Steel Research, International, 2011, vol. 18, pp. 141-47.
25. 25. X.B. Li, T.S. Zhang, Y. Min, C.J. Liu, and M.F. Jiang: Ironmak. Steelmak., 2017, vol. 46, pp. 292-300.
26. 26. Y. Liu, X.L. Wan, G.Q. Li, Y. Wang, W. Zheng, and Y.H. Hou: Sci. Technol. Weld. Joi., 2018, vol. 24, pp. 43-51.10.1080/13621718.2018.1476804 ↗
27. 27. Z. Kai, Y. Jian, R.Z. Wang, and Z.G. Yang: J. Iron Steel Res. Int., 2011, vol. 18, pp. 60-64.
28. 28. M.M. Song, C.L. Hu, B. Song, H.Y. Zhu, Z.L. Xue, and R.S. Xu: Steel Res. Int., 2018, vol. 89, pp. 1700355.10.1002/srin.201700355 ↗
29. 29. L.Y. Xu, J. Yang, J. Park, and H. Ono: Metals, 2020, vol. 10, pp. 162.10.3390/met10020162 ↗
30. 30. X.D. Zou, D.P. Zhao, J.C. Sun, C. Wang, and H. Matsuura: Metallurgical and Materials Transactions B, 2018, vol. 49, pp. 481-89.10.1007/s11663-017-1163-x ↗
31. 31. Y. Wang, L. Zhu, Q. Zhang, C. Zhang, and S. Wang: Metals, 2018, vol. 8, pp. 616.10.3390/met8080616 ↗
32. 32. R. Inoue, S. Ueda, and T. Ariyama: ISIJ Int., 2011, vol. 51, pp. 2050-55.10.2355/isijinternational.51.2050 ↗
33. 33. R. Inoue, R. Kimura, S. Ueda, and H. Suito: ISIJ Int., 2013, vol. 53, pp. 1906-12.10.2355/isijinternational.53.1906 ↗
34. 34. C.Y. Liu, X. Gao, S.J. Kim, S. Ueda, and S.Y. Kitamura: ISIJ Int., 2018, vol. 58, pp. 488-95.10.2355/isijinternational.ISIJINT-2017-593 ↗
35. 35. L.Y. Xu, J. Yang, and R.Z. Wang: Metals, 2018, vol. 8, pp. 1027.10.3390/met8121027 ↗
36. 36. J. Yang, L.Y. Xu, K. Zhu, R.Z. Wang, L.J. Zhou, and W.L. Wang: Steel Res. Int., 2015, vol. 86, pp. 619-25.10.1002/srin.201400313 ↗
37. 37. A.V. Karasev, and H. Suito: ISIJ Int., 2008, vol. 48, pp. 1507-16.10.2355/isijinternational.48.1507 ↗
38. 38. H.S. Kim, C.H. Chang, and H.G. Lee: Scripta Mater., 2005, vol. 53, pp. 1253-58.10.1016/j.scriptamat.2005.08.001 ↗
39. 39. F. Chai, C.F. Yang, S. Hang, Y.Q. Zhang, and Z. Xu: J. Iron Steel Res. Int., 2009, vol. 16, pp. 69-74.10.1016/S1006-706X(09)60013-3 ↗
40. 40. J.X. Cheng: Steelmaking Common Chart Data Manual, 2nd ed., Metallurgical Industry Press, Beijing, China, 2010.
41. 41. J. Fu, J. Zhu, L. Di, F.S. Tong, D.L. Liu, and Y.L. Wang: Acta Metall. Sin., 2000, vol. 36, pp. 801-04.
42. 42. J. Kunze, B. Beyer, S. Oswald, and W. Gruner: Steel Res., 1995, vol. 66, pp. 161-66.10.1002/srin.199501105 ↗
43. 43. K. Inoue, I. Ohnuma, H. Ohtani, K. Ishida, and T. Nishizawa: ISIJ Int., 1998, vol. 38, pp. 991-97.10.2355/isijinternational.38.991 ↗
44. 44. Y. Tomita, N. Saito, T. Tsuzuki, Y. Tokunaga, and K. Okamoto: ISIJ Int., 1994, vol. 34, pp. 829-35.10.2355/isijinternational.34.829 ↗
45. 45. L.Y. Xu, J. Yang, R.Z. Wang, W.L. Wang, and Y.N. Wang: J. Iron Steel Res. Int., 2018, vol. 25, pp. 433-41.10.1007/s42243-018-0054-y ↗
46. 46. S.J. Spachinger, W. Ernst, and N. Enzinger: Weld. World, 2017, vol. 61, pp. 1117-31.10.1007/s40194-017-0480-7 ↗