Thixoforming of an ECAPed Aluminum A356 Alloy: Microstructure Evolution, Rheological Behavior, and Mechanical Properties
Source abstract
Abstract
Thixoforming depends upon three aspects: (a) solid to liquid transformation; (b) size and morphology of the remaining solid phase in the semisolid state, and (c) the effect of both input factors on rheology of the semisolid slurry. The aluminum A356 alloy presents an ideal solid to liquid transformation, but the solidification process generates coarse aluminum dendrites surrounded by eutectic. In this regard, Equal Channel Angular Pressing (ECAP) has great potential as a method for manufacturing thixotropic raw material due to its grain refining effect. Therefore, the microstructure evolution and rheological behavior in the semisolid state of an ECAPed aluminum A356 alloy were investigated. Samples were heated up to 853 K (580 °C) and held for 0, 30, 60, 90, 210, and 600 seconds at this temperature. The isothermal heat treatment caused the globularization of the solid phase without any significant microstructure coarsening. Compression tests were carried out at the same temperature and holding times using an instrumented mechanical press. Apparent viscosities values close to 250 Pa s were obtained, revealing the exceptional rheological behavior of the produced samples. The thixoformed material also presented good mechanical properties, with high yield and ultimate tensile strength values (YS = 110/122 MPa, UTS = 173/202), and good ductility (E = 6.9/7.5 pct). These results indicate that the production of the A356 alloy via the ECAP process increases its thixoformability.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. M.C. Flemings, R.G. Riek and K.P. Young: Mater. Sci. Eng., 1976, vol. 25, pp. 103-117. DOI:10.1016/0025-5416(76)90057-410.1016/0025-5416(76)90057-4 ↗
2. M.C. Flemings: Metall. Trans. A, 1991, vol. 22A, pp. 957-981. DOI:10.1007/BF0266109010.1007/BF02661090 ↗
3. D.H. Kirkwood, M. Suéry, P. Kapranos, H.V. Atkinson and K.P. Young: Semi-solid Processing of Alloys, Springer, London, 2010, p. 172, DOI: 10.1007/978-3-642-00706-410.1007/978-3-642-00706-4 ↗
4. J.G. Sim, Y.S. Jang, J.Y. Moon, J.M. Kim, K.H. Min and C.P. Hong: ISIJ Int, 2009, vol. 49, n. 11, pp. 1700-1709. DOI: 10.2355/jsijinternational.49.170010.2355/isijinternational.49.1700 ↗
5. D. Liu, H.V. Atkinson and H. Jones: Acta Mater, 2005, vol. 53, pp. 3807-3819. DOI:10.1016/j.actmat.2005.04.02810.1016/j.actamat.2005.04.028 ↗
6. K.N. Campo, C.T.W. Proni and E.J. Zoqui: Mater. Charact., 2013, vol. 85, pp. 26-37. DOI:10.1016/j.matchar.2013.08.01110.1016/j.matchar.2013.08.011 ↗
7. V.M. Segal: Mater. Sci. Eng. A, 1995, vol. 197A, pp. 157-164. DOI:10.1016/0921-5093(95)09705-810.1016/0921-5093(95)09705-8 ↗
8. Z. Zhao, Y. Cheng, Q. Chen, Y. Wang and D. Shu: Trans. Nonferr. Metal. Soc., 2010, vol. 20, pp. 178-182. DOI: 10.1016/S1003-6326(09)60117-510.1016/S1003-6326(09)60117-5 ↗
9. S. Ashouri, M. Nili-Ahmadabadi, M. Moradi and M. Iranpour: J. Alloys. Compd., 2008, vol. 466, pp. 67-72. DOI:10.1016/j.jallcom.2007.11.01010.1016/j.jallcom.2007.11.010 ↗
10. E. Tzimas and A. Zavaliangos: Mater. Sci. Eng. A, 2000, vol. 289A, pp. 217-227. DOI:10.1016/S0921-5093(00)00907-210.1016/S0921-5093(00)00907-2 ↗
11. E.J. Zoqui, M. Paes and E. Es-Sadiqi: J. Mater. Process. Technol., 2002, vol. 120, pp. 365–373. DOI:10.1016/S0924-0136(01)01148-710.1016/S0924-0136(01)01148-7 ↗
12. E.J. Zoqui, M.T. Shehata, M. Paes, V. Kao and E. Es-Sadiqi: Mater. Sci. Eng. A, 2002, vol. 325, pp. 38–53. DOI:10.1016/S0921-5093(01)01401-010.1016/S0921-5093(01)01401-0 ↗
13. C.T.W. Proni, M.A. d’Ávila and E.J. Zoqui: Int. J. Mater. Res., 2013, vol. 104, pp. 1182-1196. DOI:10.3139/146.11098310.3139/146.110983 ↗
14. E.J. Zoqui and M.H. Robert: J. Mater. Process. Technol., 2001, vol. 109, pp. 215-219. DOI:10.1016/S0924-0136(00)00798-610.1016/S0924-0136(00)00798-6 ↗
15. E.J. Zoqui, M. Paes and M.H. Robert: J. Mater. Process. Technol., 2004, vol. 153-154, pp. 300-306. DOI:10.1016/j.jmatprotec.2004.04.06810.1016/j.jmatprotec.2004.04.068 ↗
16. G. Yan, S. Zhao, S. Ma and H. Shou: Mater. Charact., 2012, vol. 69, pp. 45-51. DOI:10.1016/j.matchar.2012.04.00510.1016/j.matchar.2012.04.005 ↗
17. N. Haghdadi, A. Zarei-Hanzaki, S. Heshmati-Manesh, H.R. Abedi and S.B. Hassas-Irani: Mater. Design., 2013, vol.49, pp. 878-887. DOI:10.1016/j.matdes.2013.02.05110.1016/j.matdes.2013.02.051 ↗
18. C.G. Kang, J.S. Choi and K.H. Kim: J. Mater. Process. Technol., 1999, vol. 88, pp. 159-168. DOI:10.1016/S0924-0136(98)00383-510.1016/S0924-0136(98)00383-5 ↗
19. E.A. Viera and M. Ferrante: Acta Mater., 2005, vol. 53, pp. 5379-5386. DOI:10.1016/j.actmat.2005.08.01410.1016/j.actamat.2005.08.014 ↗
20. T.Y. Liu, H.V. Atkinson, P. Kapranos, D.H. Kirkwood and S.C. Hogg: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 1545-1554. DOI:10.1007/s11661-003-0266-y10.1007/s11661-003-0266-y ↗
21. M. Paes and E.J. Zoqui: Mater. Sci. Eng. A, 2005, vol. 406A, pp. 63-73. DOI:10.1016/j.msea.2005.07.01810.1016/j.msea.2005.07.018 ↗
22. J.M. García-Infanta, A.P. Zhilyaev, C.M. Cepeda-Jiménez, O.A. Ruano and F. Carreño: Scripta Mater., 2008, vol. 58, pp. 138-141. DOI:10.1016/j.scriptamat.2007.09.01810.1016/j.scriptamat.2007.09.018 ↗
23. M. Moradi, M. Nili-Ahmadabadi and B. Heidarian: Int. J. Mater. Form., 2009, vol. 2, pp. 85-88. DOI:10.1007/s12289-009-0641-310.1007/s12289-009-0641-3 ↗
24. C.H. Cáceres, C.J. Davidson and J.R. Griffiths: Mater. Sci. Eng. A, 1995, vol. 197A, pp. 171-179. DOI:10.1016/0921-5093(94)09775-510.1016/0921-5093(94)09775-5 ↗
25. Q.G. Wang and C.H. Cáceres: Mater. Sci. Eng. A, 1998, vol. 241A, pp. 72-82. DOI:10.1016/S0921-5093(97)00476-010.1016/S0921-5093(97)00476-0 ↗
26. J.M. Gárcia-Infanta, A.P. Zhilyaev, C.M. Cepeda-Jiménez, A.O. Ruano and F. Carreño: Scripta Mater., 2008, vol. 58, pp. 138-141. DOI:10.1016/j.scriptamat.2007.09.01810.1016/j.scriptamat.2007.09.018 ↗
27. W. Jiang, Z. Fan, D. Liu, D. Liao, X. Dong and X. Zong: Mater. Sci. Eng. A, 2013, vol. 560A, pp. 396-403. DOI:10.1016/j.msea.2012.09.08410.1016/j.msea.2012.09.084 ↗
28. C.H. Cáceres and J.R. Griffiths: Acta Mater., 1996, vol. 44, pp. 25-33. DOI:10.1016/1359-6454(95)00172-810.1016/1359-6454(95)00172-8 ↗
29. C.H. Cáceres, J.R. Davidson, J.R. Griffiths and Q.G. Wang: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 2611-2618. DOI:10.1007/s11661-999-0301-810.1007/s11661-999-0301-8 ↗
30. Q.G. Wang, C.H. Cáceres and J.R. Griffiths: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2901-2912. DOI:10.1007/s11661-003-0190-110.1007/s11661-003-0190-1 ↗
31. C.H. Cáceres and B.I. Selling: Mater. Sci. Eng. A, 1996, vol. 220A, pp. 109-116. DOI:10.1016/S0921-5093(96)10433-010.1016/S0921-5093(96)10433-0 ↗
32. C.D. Lee: Mater. Sci. Eng. A, 2007, vol. 464A, pp. 249-254. DOI:10.1016/j.msea.2007.01.13010.1016/j.msea.2007.01.130 ↗
33. H. Mae, X. Teng, Y. Bai and T. Wierzbicki: J Solid Mech and Mater Eng, 2008, vol. 2, n. 7, pp 924-942. DOI:10.1299/jmmp.2.92410.1299/jmmp.2.924 ↗