journal article·2023-01

Effect of Annealing Temperature on Microstructure and Properties of a Heavy Warm Rolled Nickel Aluminum Bronze Alloy

Shuo Ma, Xuan Li, Xiaobin Yang, Liming Fu, Lei Liu, Mingxu Xia, Aidang Shan

Publisher page

Abstract

High strength and ductile nickel aluminum bronze (NAB) alloys were produced by heavy warm rolling (HWR) and subsequent annealing at various temperatures. The effect of annealing temperatures ranging from 473 K to 1173 K (200 °C to 900 °C) on the microstructure, mechanical, and electrochemical properties of these HWRed NAB alloys was studied. The results show that the evolution of microstructure and mechanical behavior can be divided into three distinct stages with the increasing annealing temperature. When annealed below 500 °C (Stage A), the HWRed samples exhibit ultrahigh strength and good ductility. Such remarkable tensile properties are mainly attributed to the ultrafine α grains and nano k precipitates. Part of the α phase recrystallized, contributing to a further decrease in the average grain size. An ultrahigh ultimate strength of 1363 MPa and uniform elongation of 6.0 pct can be obtained when the alloy is annealed at 400 °C for 1 hour. When annealed at 600 °C and 700 °C (Stage B), a prominent strength–ductility combination with a yield strength of about 1000 MPa and an elongation of about 15 pct can be achieved, mainly due to the uniform ultrafine microstructures and the high-density annealing twins. Some nano k phases with grain size less than 20 nm precipitate dispersedly in α grains, which may also be a significant strengthening factor. When the temperature reaches above 800 °C (Stage C), the yield strength reduces dramatically, while the elongation and ultimate strength further increase. At this stage, the matrix transforms from single ultrafine α grains into a fine-grained (α + β′) duplex structure with high-density ultrafine annealing twins inside α grains. It is found that the mechanical properties of the HWRed and annealed alloys are greatly enhanced, while the electrochemical stability almost shows no deterioration compared with the undeformed coarse-grained alloys. This indicates that HWR and subsequent annealing is an effective strategy for preparing bulk NAB alloys with high performance.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallurgy and Material Science · Aluminum Alloy Microstructure Properties · Nanoporous metals and alloys

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (69)

Show source-provided references
1. G. Kear, B.D. Barker, K. Stokes, and F.C. Walsh: J. Appl. Electrochem., 2004, vol. 34, pp. 1235–40.10.1007/s10800-004-1758-1 ↗
2. S. Ma, L. Fu, and A. Shan: Mater. Charact., 2021, vol. 177, p. 111057.10.1016/j.matchar.2021.111057 ↗
3. D.R. Ni, B.L. Xiao, Z.Y. Ma, Y.X. Qiao, and Y.G. Zheng: Corros. Sci., 2010, vol. 52, pp. 1610–17.10.1016/j.corsci.2010.02.026 ↗
4. Z. Wu, Y.F. Cheng, L. Liu, W. Lv, and W. Hu: Corros. Sci., 2015, vol. 98, pp. 260–70.10.1016/j.corsci.2015.05.037 ↗
5. S.K. Menon, F.A. Pierce, B.P. Rosemark, K. Oh-Ishi, S. Swaminathan, and T.R. Mcnelley: Metall. and Mater. Trans. A., 2012, vol. 43A, pp. 3687–3702.10.1007/s11661-012-1181-x ↗
6. Y. Lv, B. Zhao, H. Zhang, C. Su, and F. Lyu: Mater. Trans., 2019, vol. 60, pp. 1629–37.10.2320/matertrans.M2019031 ↗
7. D. Zhang, R. Chen, W. Zhang, Z. Luo, and Y. Li: Acta Metall. Sin. (Engl. Lett.), 2010, vol. 23, pp. 113–20.
8. E.A. Culpan and G. Rose: J. Mater. Sci., 1978, vol. 13, pp. 1647–57.10.1007/BF00548728 ↗
9. A. Jahanafrooz, F. Hasan, G.W. Lorimer, and N. Ridley: Metall. Trans. A, 1983, vol. 14, pp. 1951–56.10.1007/BF02662362 ↗
10. F. Hasan, A. Jahanafrooz, G.W. Lorimer, and N. Ridley: Metall. Trans. A, 1982, vol. 13, pp. 1337–45.10.1007/BF02642870 ↗
11. J. Anantapong, V. Uthaisangsuk, S. Suranuntchai, and A. Manonukul: Mater. Des., 2014, vol. 60, pp. 233–43.10.1016/j.matdes.2014.03.033 ↗
12. Z. Bingjie, L. Yuting, D. Yang, W. Liqiang, and L. Weijie: Mater. Charact., 2018, vol. 144, pp. 77–85.10.1016/j.matchar.2018.07.002 ↗
13. Y. Zeng, F. Yang, Z. Chen, E. Guo, and T. Wang: J. Mater. Sci. Technol., 2021, vol. 144, pp. 77–85.
14. Z. Qin, Q. Zhang, Q. Luo, Z. Wu, B. Shen, L. Liu, and W. Hu: Corros. Sci., 2018, vol. 139, pp. 255–66.10.1016/j.corsci.2018.04.043 ↗
15. S. Zeng, S. Hu, B. Peng, K. Hu, and M. Xiao: Mater. Des., 2022, vol. 220, p. 110853.10.1016/j.matdes.2022.110853 ↗
16. C. Dharmendra, K. Gururaj, K. Pradeep, and M. Mohammadi: Addit. Manuf., 2021, vol. 46, p. 102137.
17. K. Oh-Ishi and T.R. Mcnelley: Metall. and Mater. Trans. A., 2005, vol. 36, pp. 1575–85.10.1007/s11661-005-0249-2 ↗
18. B.P. Pisarek: Nephron Clin. Pract., 2014, vol. 14, pp. 61–66.
19. Y. Lv, D. Yang, Y. Han, L.C. Zhang, L. Wang, and W. Lu: Mater. Sci. Eng. A, 2017, vol. 685, pp. 439–46.10.1016/j.msea.2016.12.050 ↗
20. P. Swann and H. Warlimont: Acta Metall., 1963, vol. 11, pp. 511–27.10.1016/0001-6160(63)90086-5 ↗
21. S. Kajiwara and Z. Nishiyama: Jpn. J. Appl. Phys., 1964, vol. 3, p. 749.10.1143/JJAP.3.749 ↗
22. Z. Nishiyama and S. Kajiwara: Jpn. J. Appl. Phys., 1963, vol. 2, p. 478.10.1143/JJAP.2.478 ↗
23. Y. Liu, J. Mazumder, and K. Shibata: Acta Metall. Mater., 1994, vol. 42, pp. 1755–62.10.1016/0956-7151(94)90386-7 ↗
24. D.M. Lloyd, G.W. Lorimer, and N. Ridley: Met. Technol., 1980, vol. 7, pp. 114–119.10.1179/030716980803286577 ↗
25. X. Xu, Y. Lv, H. Meng, X. Di, L. Zhang, L. Wang, and W. Lu: Int. J. Fatigue, 2016, vol. 82, pp. 579–87.10.1016/j.ijfatigue.2015.09.014 ↗
26. D. Yang, Y. Lv, C. Kai, B. Zhao, Y. Han, L. Wang, and W. Lu: Mater. Sci. Eng. A, 2018, vol. 733, pp. 361–73.10.1016/j.msea.2018.07.049 ↗
27. S. Ma, L. Fu, X. Ma, and A. Shan: Mater. Charact., 2019, vol. 158, p. 109986.10.1016/j.matchar.2019.109986 ↗
28. J. Su, S. Swaminathan, S.K. Menon, and T.R. Mcnelley: Metall. Mater. Trans. A., 2011, vol. 42A, pp. 2420–30.10.1007/s11661-011-0638-7 ↗
29. D. Xiong, L. Wang, X. Xu, Y. Lv, and W. Lv: Mater Mech. Eng., 2017, vol. 41, pp. 15–9.
30. C.J. Barr and K. Xia: J. Mater. Sci., 2013, vol. 48, pp. 4749–57.10.1007/s10853-013-7256-2 ↗
31. R.Z. Valiev, R.K. Islamgaliev, and I.V. Alexandrov: Prog. Mater Sci., 2000, vol. 45, pp. 103–89.10.1016/S0079-6425(99)00007-9 ↗
32. Y. Lv, L. Wang, Y. Han, X. Xu, and W. Lu: Mater. Sci. Eng., A, 2015, vol. 643, pp. 17–24.10.1016/j.msea.2015.06.078 ↗
33. M. Lotfollahi: Mater. Des., 2014, vol. 62, pp. 282–87.10.1016/j.matdes.2014.05.037 ↗
34. J.P. Ault: NACE International, Houston, TX (United States) 1995.
35. Q.N. Song, D.R. Ni, and Y.G. Zheng: Corrosion, 2014, vol. 70, pp. 261–70.10.5006/1070 ↗
36. Y. Hong, Y. Zheng, and Z. Yao: J. Mater. Sci. Technol., 2009, vol. 25, pp. 758–66.
37. F. Hasan, G.W. Lorimer, and N. Ridley: J. Phys. Colloques, 1982, vol. 43, pp. C4-653-4–658.10.1051/jphyscol:19824105 ↗
38. M. Stern and A.L. Geary: J. Electrochem. Soc., 1957, vol. 104, p. 56.10.1149/1.2428496 ↗
39. Z. Li, L. Fu, H. Zheng, R. Yu, L. Lv, Y. Sun, X. Dong, and A. Shan: Metall. Mater. Trans. A., 2019, vol. 50A, pp. 3223–27.10.1007/s11661-019-05231-y ↗
40. C.S. Pande, B.B. Rath, and M.A. Imam: Mater. Sci. Eng. A, 2004, vol. 304, pp. 422–26.
41. L. Lu, Y. Shen, X. Chen, L. Qian, and K. Lu: Science, 2009, vol. 324, pp. 349–52.10.1126/science.1159610 ↗
42. S. Qu, P. Zhang, S.D. Wu, Q.S. Zang, and Z.F. Zhang: Scripta Mater., 2008, vol. 59, pp. 1131–34.10.1016/j.scriptamat.2008.07.037 ↗
43. K. Lu, L. Lu, and S. Suresh: Science, 2004, vol. 304, pp. 422–26.10.1126/science.1092905 ↗
44. K. Ma, H. Wen, H. Tao, T.D. Topping, and J.M. Schoenung: Acta Mater., 2014, vol. 62, pp. 141–55.10.1016/j.actamat.2013.09.042 ↗
45. F.J. Nie and C.B. Muddle: Acta Mater., 2008, vol. 56, pp. 3490–3501.10.1016/j.actamat.2008.03.028 ↗
46. H. Wen, T.D. Topping, D. Isheim, D.N. Seidman, and E.J. Lavernia: Acta Mater., 2013, vol. 61, pp. 2769–82.10.1016/j.actamat.2012.09.036 ↗
47. Y. Tang, Y. Kang, L. Yue, and X. Jiao: J. Alloy. Compd., 2017, vol. 695, pp. 613–25.10.1016/j.jallcom.2016.11.014 ↗
48. P. Brezina: Int Met Rev, 1982, vol. 27, pp. 77–120.10.1179/imr.1982.27.1.77 ↗
49. Y. Sun, L. Fu, Z. Fu, A. Shan, and E.J. Lavernia: Scripta Mater., 2017, vol. 141, pp. 1–5.10.1016/j.scriptamat.2017.07.013 ↗
50. D. Yang, Y. Lv, B. Zhao, Y. Han, L. Wang, and W. Lu: Mater. Charact., 2018, vol. 144, pp. 356–67.10.1016/j.matchar.2018.07.033 ↗
51. E.A. Nelson: Naval Postgraduate School Monterey Ca, 2009.
52. B.S. Amirkhiz, D. Chalasani, and M. Mohammadi: Microsc. Microanal., 2019, vol. 25, pp. 2588–89.10.1017/S1431927619013679 ↗
53. C. Dharmendra, K. Rice, B. Amirkhiz, and M. Mohammadi: Mater. Des., 2021, vol. 202, p. 109541.10.1016/j.matdes.2021.109541 ↗
54. S.M. Orzolek, J.K. Semple, and C.R. Fisher: Addit. Manuf., 2022, vol. 56, p. 102859.
55. G. Xie, Q. Wang, M.I. Xujun, B. Xiong, and L. Peng: Mater. Sci. Eng. A, 2012, vol. 558, pp. 326–30.10.1016/j.msea.2012.08.007 ↗
56. G. Yong, C. Liu, Y. Gao, D. Zhu, H. Tan, and S. Jiang: Mater. Charact., 2017, vol. 129, pp. 156–62.10.1016/j.matchar.2017.04.026 ↗
57. A. Xf, C. Xwb, and A. Qy: Materials Today Nano, 2018, vol. 3, pp. 48–53.10.1016/j.mtnano.2018.11.004 ↗
58. G. Dini, R. Ueji, A. Najafizadeh, and S.M. Monir-Vaghefi: Mater. Sci. Eng. A, 2010, vol. 527, pp. 2759–763.10.1016/j.msea.2010.01.033 ↗
59. M. Yang, D. Yan, F. Yuan, P. Jiang, E. Ma, and X. Wu: Proc. Natl. Acad. Sci. U.S.A., 2018, vol. 115, pp. 7224–229.10.1073/pnas.1807817115 ↗
60. S. Fonlupt, B. Bayle, D. Delafosse, and J.L. Heuze: Corros. Sci., 2005, vol. 47, pp. 2792–806.10.1016/j.corsci.2004.09.025 ↗
61. Y.L. Wang, Q.L. Pan, L.L. Wei, B. Li, and Y. Wang: Mater. Des., 2014, vol. 55, pp. 857–63.10.1016/j.matdes.2013.09.063 ↗
62. H. Zhang, M. Sun, Y. Liu, D. Ma, and Y. Li: Acta Mater., 2021, vol. 211, p. 116878.10.1016/j.actamat.2021.116878 ↗
63. R. Gürbüz and N. Akgün: Mater. Corros., 2019, vol. 70, pp. 1788–797.10.1002/maco.201910887 ↗
64. H. Vehoff, A. Nykyforchyn, and R. Metz: Mater. Sci. Eng. A, 2004, vol. 387, pp. 546–51.10.1016/j.msea.2003.12.094 ↗
65. C. Wang, C. Jiang, Z. Chai, M. Chen, L. Wang, and V. Ji: Surf. Coat. Technol., 2017, vol. 313, pp. 136–42.10.1016/j.surfcoat.2017.01.073 ↗
66. F. Yang, H. Kang, E. Guo, R. Li, Z. Chen, Y. Zeng, and T. Wang: Corros. Sci., 2018, vol. 139, pp. 333–45.10.1016/j.corsci.2018.05.012 ↗
67. C. Liu, X. Li, R.I. Revilla, T. Sun, and X. Li: Corros. Sci., 2021, vol. 179, p. 109150.10.1016/j.corsci.2020.109150 ↗
68. Z.Z. Shi, J. Yu, X.F. Liu, and L.N. Wang: J. Mater. Sci. Technol., 2018, vol. 034, pp. 1008–015.10.1016/j.jmst.2017.11.026 ↗
69. Z. Qin, D.-H. Xia, Y. Zhang, Z. Wu, L. Liu, Y. Lv, Y. Liu, and W. Hu: Corros. Sci., 2020, vol. 174, p. 108744.10.1016/j.corsci.2020.108744 ↗