Revealing Microstructural, Textural, and Hardness Evolution of Ti–6Al–4V Sheet Cooled From Sub β-Transus Temperature at Different Rates
Source abstract
Abstract
A hot-rolled Ti–6Al–4V sheet was annealed at 960 °C (sub β-transus temperature) and then subjected to different coolings [in water (WC), air (AC), and furnace (FC)]. Microstructural and textural characteristics were systematically characterized and quantitatively analyzed by combined use of multiple characterization techniques, with hardness also examined. Results indicate that both WC and AC specimens possess mixed microstructures of primary bulk α (αp) grains and transformed secondary α (αs) plates. The rapid WC allows the β → α transformation to be complete (martensite) while a small amount of residual thin β film (V-enriched) exists in the AC specimen. Plate structures are absent in the FC specimen with its microstructure consisting of coarse-equiaxed αp grains and residual β phase. For all the cooled specimens, their major textural feature is quite similar to that of the as-received material, while the textural intensity increases at lower cooling rates due to specific αp grain growth and αs variant selection. For rapid cooling in water, however, a single β orientation is able to give birth to twelve different αs variants, producing new textural components and a globally weakened texture. The hardness of the WC specimen (379.7 ± 5.5 HV) is higher than that of the as-received material (366.1 ± 4.3 HV), which can be ascribed to combined contributions from grain refinement and solid solution of alloying elements due to the martensitic transformation. With decreasing cooling rates, specimen hardness is reduced from 342.5 ± 4.9 HV (AC specimen) to 327.2 ± 4.6 HV (FC specimen) because of increased grain sizes.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Intermetallics and Advanced Alloy Properties · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. X.S. Zhang, Y.J. Chen, and J.L. Hu: Prog. Aerosp. Sci., 2018, vol. 97, pp. 22–34.10.1016/j.paerosci.2018.01.001 ↗
2. L.-Y. Chen, Y.-W. Cui, and L.-C. Zhang: Metals, 2020, vol. 10, p. 1139.10.3390/met10091139 ↗
3. S. Attarilar, F. Djavanroodi, M. Ebrahimi, K.J. Al-Fadhalah, L. Wang, and M. Mozafari: J. Biomed. Nanotechnol., 2021, vol. 17, pp. 115–30.10.1166/jbn.2021.3015 ↗
4. L.-Y. Chen, S.-X. Liang, Y. Liu, and L.-C. Zhang: Mater. Sci. Eng. R, 2021, vol. 146, 100648.10.1016/j.mser.2021.100648 ↗
5. F.J. Gil, M.P. Ginebra, J.M. Manero, and J.A. Planell: J. Alloys Compd., 2001, vol. 329, pp. 142–52.10.1016/S0925-8388(01)01571-7 ↗
6. E. Farabi, P.D. Hodgson, G.S. Rohrer, and H. Beladi: Acta Mater., 2018, vol. 154, pp. 147–60.10.1016/j.actamat.2018.05.023 ↗
7. Y. Chong, T. Bhattacharjee, J. Yi, A. Shibata, and N. Tsuji: Scripta Mater., 2017, vol. 138, pp. 66–70.10.1016/j.scriptamat.2017.05.038 ↗
8. N. Davari, A. Rostami, and S.M. Abbasi: Mater. Sci. Eng. A, 2017, vol. 683, pp. 1–8.10.1016/j.msea.2016.11.095 ↗
9. N. Kherrouba, M. Bouabdallah, R. Badji, D. Carron, and M. Amir: Mater. Chem. Phys., 2016, vol. 181, pp. 462–69.10.1016/j.matchemphys.2016.06.082 ↗
10. I. Lonardelli, N. Gey, H.-R. Wenk, M. Humbert, S.C. Vogel, and L. Lutterotti: Acta Mater., 2007, vol. 55, pp. 5718–27.10.1016/j.actamat.2007.06.017 ↗
11. N. Stanford and P.S. Bate: Acta Mater., 2004, vol. 52, pp. 5215–24.10.1016/j.actamat.2004.07.034 ↗
12. D. Bhattacharyya, G.B. Viswanathan, R. Denkenberger, D. Furrer, and H.L. Fraser: Acta Mater., 2003, vol. 51, pp. 4679–91.10.1016/S1359-6454(03)00179-4 ↗
13. H. Beladi, Q. Chao, and G.S. Rohrer: Acta Mater., 2014, vol. 80, pp. 478–89.10.1016/j.actamat.2014.06.064 ↗
14. G.C. Obasi, S. Birosca, J. Quinta Da Fonseca, and M. Preuss: Acta Mater., 2012, vol. 60, pp. 1048–58.10.1016/j.actamat.2011.10.038 ↗
15. W.G. Burgers: Physica, 1934, vol. 1, pp. 561–86.10.1016/S0031-8914(34)80244-3 ↗
16. S.L. Semiatin, S.L. Knisley, P.N. Fagin, F. Zhang, and D.R. Barker: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2377–86.10.1007/s11661-003-0300-0 ↗
17. J.H. Dai, J.Y. Xia, L.J. Chai, K.L. Murty, N. Guo, and M.R. Daymond: J. Mater. Sci., 2020, vol. 55, pp. 8346–62.10.1007/s10853-020-04603-9 ↗
18. S.A. Souza, R.B. Manicardi, P.L. Ferrandini, C.R.M. Afonso, A.J. Ramirez, and R. Caram: J. Alloys Compd., 2010, vol. 504, pp. 330–40.10.1016/j.jallcom.2010.05.134 ↗
19. H.P. Lee, C. Esling, and H.J. Bunge: Textures Microstruct., 1988, vol. 7, pp. 317–37.10.1155/TSM.7.317 ↗
20. S.V.S.N. Murty, N. Nayan, P. Kumar, P.R. Narayanan, S.C. Sharma, and K.M. George: Mater. Sci. Eng. A, 2014, vol. 589, pp. 174–81.10.1016/j.msea.2013.09.087 ↗
21. L.-Y. Chen, H.-Y. Zhang, C. Zheng, H.-Y. Yang, P. Qin, C. Zhao, S. Lu, S.-X. Liang, L. Chai, and L.-C. Zhang: Mater. Des., 2021, vol. 208, 109907.10.1016/j.matdes.2021.109907 ↗
22. T. Ahmed and H.J. Rack: Mater. Sci. Eng. A, 1998, vol. 243, pp. 206–11.10.1016/S0921-5093(97)00802-2 ↗
23. R.P. Kolli and A. Devaraj: Metals, 2018, vol. 8, p. 506.10.3390/met8070506 ↗
24. Y.B. Chun, M. Battaini, C.H.J. Davies, and S.K. Hwang: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 3473–87.10.1007/s11661-010-0410-4 ↗
25. X. Hu, L. Chai, Y. Zhu, H. Wu, J. Luo, L. Tian, Q. Sun, Y. Li, and J. Cheng: Mater. Today Commun., 2021, vol. 29, 102989.10.1016/j.mtcomm.2021.102989 ↗
26. S.C. Wang, M. Aindow, and M.J. Starink: Acta Mater., 2003, vol. 51, pp. 2485–2503.10.1016/S1359-6454(03)00035-1 ↗
27. L.J. Chai, B.F. Chen, Z.M. Zhou, K.L. Murty, Y.L. Ma, and W. Huang: Mater. Charact., 2015, vol. 104, pp. 61–65.10.1016/j.matchar.2015.04.008 ↗
28. G.C. Obasi, S. Birosca, D.G.L. Prakash, J. Quinta da Fonseca, and M. Preuss: Acta Mater., 2012, vol. 60, pp. 6013–24.10.1016/j.actamat.2012.07.025 ↗
29. J.L.W. Warwick, N.G. Jones, I. Bantounas, M. Preuss, and D. Dye: Acta Mater., 2013, vol. 61, pp. 1603–15.10.1016/j.actamat.2012.11.037 ↗
30. Z.B. Zhao, Q.J. Wang, Q.M. Hu, J.R. Liu, B.B. Yu, and R. Yang: Acta Mater., 2017, vol. 126, pp. 372–82.10.1016/j.actamat.2016.12.069 ↗
31. N. Gey and M. Humbert: Acta Mater., 2002, vol. 50, pp. 277–87.10.1016/S1359-6454(01)00351-2 ↗
32. L.J. Chai, J.Y. Xia, Y. Zhi, K. Chen, T.T. Wang, B. Song, and N. Guo: Mater. Chem. Phys., 2018, vol. 213, pp. 414–21.10.1016/j.matchemphys.2018.04.044 ↗
33. Z. Zheng, L. Chai, Z. Li, W. Huang, L. Tian, Y. Wang, and L. Liu: Mater. Chem. Phys., 2022, vol. 276, 125318.10.1016/j.matchemphys.2021.125318 ↗
34. J. Romero, M. Preuss, and J. Quinta da Fonseca: Acta Mater., 2009, vol. 57, pp. 5501–11.10.1016/j.actamat.2009.07.046 ↗
35. E. Sarath Kumar Menon and R. Krishnan: J. Mater. Sci., 1983, vol. 18, pp. 365–74.10.1007/BF00560624 ↗
36. D. Bhattacharyya, G.B. Viswanathan, S.C. Vogel, D.J. Williams, V. Venkatesh, and H.L. Fraser: Scripta Mater., 2006, vol. 54, pp. 231–36.10.1016/j.scriptamat.2005.09.026 ↗
37. G.G.E. Seward, S. Celotto, D.J. Prior, J. Wheeler, and R.C. Pond: Acta Mater., 2004, vol. 52, pp. 821–32.10.1016/j.actamat.2003.10.049 ↗
38. S.V. Zherebtsov, G.S. Dyakonov, A.A. Salem, V.I. Sokolenko, G.A. Salishchev, and S.L. Semiatin: Acta Mater., 2013, vol. 61, pp. 1167–78.10.1016/j.actamat.2012.10.026 ↗
39. T.T. Wang, L.G. Zeng, Z.J. Li, L.J. Chai, T.J. Cheng, L. Zhang, V. Fallah, Q. Dong, and Z.W. Yao: Metall. Mater. Trans. A, 2019, vol. 50A, pp. 3794–3804.10.1007/s11661-019-05312-y ↗
40. L.J. Chai, H. Wu, Z.Y. Zheng, H.T. Guan, H.C. Pan, N. Guo, and B. Song: J. Alloys Compd., 2018, vol. 741, pp. 116–22.10.1016/j.jallcom.2018.01.113 ↗
41. H. Conrad: Prog. Mater. Sci., 1981, vol. 26, pp. 123–403.10.1016/0079-6425(81)90001-3 ↗
42. P. Luo, D.T. McDonald, W. Xu, S. Palanisamy, M.S. Dargusch, and K. Xia: Scripta Mater., 2012, vol. 66, pp. 785–88.10.1016/j.scriptamat.2012.02.008 ↗
43. M.L. Meier, D.R. Lesuer, and A.K. Mukherjee: Mater. Sci. Eng. A, 1992, vol. 154, pp. 165–73.10.1016/0921-5093(92)90342-X ↗
44. A. Fitzner, J. Palmer, B. Gardner, M. Thomas, M. Preuss, and J. Quinta da Fonseca: J. Mater. Sci., 2019, vol. 54, pp. 7961–74.10.1007/s10853-019-03431-w ↗