journal article·2019-11Open access

In Situ Observation of Bainite Transformation and Simultaneous Carbon Enrichment in Austenite in Low-Alloyed TRIP Steel Using Time-of-Flight Neutron Diffraction Techniques

Yusuke Onuki, Takashi Hirano, Akinori Hoshikawa, Shigeo Sato, Toshiro Tomida

Abstract

An in situ neutron diffraction experiment during austempering of low-alloyed transformation-induced plasticity steel, Fe-1.48Si-1.52Mn-0.15C, in wt pct was conducted. In this study, time-of-flight neutron diffractometer with a large detector coverage, iMATERIA at J-PARC MLF, was employed. The phase fraction and carbon concentration in austenite could be quantitatively determined with a time resolution 1 minute although considerable textures existed for both ferrite and austenite. The carbon concentration in austenite during austempering was found to be inhomogeneous, resulting in a bimodal concentration distribution. The low-carbon region was consumed by bainite transformation whereas the high-carbon austenite slightly increased and even survived the final cooling to room temperature, forming a retained austenite. The rate of bainite transformation was affected by the state prior to the start of austempering. Consequently, different morphological features of the retained austenite were formed. More block-shaped austenite was observed in the case of slower bainite transformation, and it was determined that film-shaped austenite could also exist. The average carbon concentration was similar to that of high-carbon austenite during austempering. Hence, the film and block shapes of the retained austenite do not necessarily reflect the difference in carbon concentration.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. H. K. D. H. Bhadeshia: Bainite in steels. 3 ed. (Many Publishing, Leeds, UK, 2015).
2. O. D. Sherby, J. Wadsworth, D. R. Lesuer and C. K. Syn: Mater. Trans. 2008, vol. 49, pp. 2016-2027.10.2320/matertrans.MRA2007338 ↗
3. Y. Tomita and T. Okawa: Mater. Sci. Technol. 2013, vol. 11, pp. 245-251.10.1179/mst.1995.11.3.245 ↗
4. S. Zaefferer, J. Ohlert and W. Bleck: Acta Mater. 2004, vol. 52, pp. 2765-2778.10.1016/j.actamat.2004.02.044 ↗
5. L. Guo, H. K. D. H. Bhadeshia, H. Roelofs and M. I. Lembke: Mater. Sci. Technol. 2017, vol. 33, pp. 2147-2156.10.1080/02670836.2017.1353669 ↗
6. H. Nishijima, Y. Tomota, Y. Su, W. Gong and J.-i. Suzuki: Metals 2016, vol. 6, p. 16.10.3390/met6010016 ↗
7. K. Rakha, H. Beladi, I. Timokhina, X. Xiong, S. Kabra, K.-D. Liss and P. Hodgson: Materials Science and Engineering: A 2014, vol. 589, pp. 303-309.10.1016/j.msea.2013.09.055 ↗
8. H. Stone, M. Peet, H. Bhadeshia, P. Withers, S. S. Babu and E. D. Specht: Proc. Royal Soc. Lond. A 2008, vol. 464, pp. 1009-1027.10.1098/rspa.2007.0201 ↗
9. M. Y. Sherif, C. G. Mateo, T. Sourmail and H. K. D. H. Bhadeshia: Mater. Sci. Technol. 2004, vol. 20, pp. 319-322.10.1179/026708304225011180 ↗
10. Y. Onuki, A. Hoshikawa, S. Sato, T. Ishigaki and T. Tomida: J. Mater. Sci. 2017, vol. 52, pp. 11643-11658.10.1007/s10853-017-1309-x ↗
11. H. R. Wenk, L. Lutterotti and S. Vogel: Nucl. Instrum. Meth. Phys. Res. A 2003, vol. 515, pp. 575-588.10.1016/j.nima.2003.05.001 ↗
12. H. R. Wenk, S. Matthies and L. Lutterotti: Mater. Sci. Forum 1994, vol. 157-162, pp. 473-480.10.4028/www.scientific.net/MSF.157-162.473 ↗
13. L. Lutterotti, S. Matthies, H. R. Wenk, A. S. Schultz and J. W. Richardson: J. Appl. Phys. 1997, vol. 81, pp. 594-600.10.1063/1.364220 ↗
14. P. J. Jacques, S. Allain, O. Bouaziz, A. De, A. F. Gourgues, B. M. Hance, Y. Houbaert, J. Huang, A. Iza-Mendia, S. E. Kruger, M. Radu, L. Samek, J. Speer, L. Zhao and S. van der Zwaag: Mater. Sci. Technol. 2009, vol. 25, pp. 567-574.10.1179/174328408X353723 ↗
15. Y. Onuki, A. Hoshikawa, S. Sato, P. Xu, T. Ishigaki, Y. Saito, H. Todoroki and M. Hayashi: J. Appl. Crystallogr. 2016, vol. 49, pp. 1579-1584.10.1107/S160057671601164X ↗
16. R. Blondé, E. Jimenez-Melero, L. Zhao, J. P. Wright, E. Brück, S. van der Zwaag and N. H. van Dijk: Acta Mater. 2012, vol. 60, pp. 565-577.10.1016/j.actamat.2011.10.019 ↗
17. L. Lutterotti, D. Chateigner, S. Ferrari and J. Ricote: Thin Solid Films 2004, vol. 450, pp. 34-41.10.1016/j.tsf.2003.10.150 ↗
18. K. W. Andrews: J. Iron Steel Inst. 1965, vol. 203, pp. 721-727.
19. H. K. D. H. Bhadeshia: Metal Science 2013, vol. 16, pp. 159-166.10.1179/030634582790427217 ↗
20. T. Suzuki, Y. Ono, G. Miyamoto and T. Furuhara: ISIJ Int. 2010, vol. 50, pp. 1476-1482.10.2355/isijinternational.50.1476 ↗
21. T. Tomida: Acta Mater. 2018, vol. 146, pp. 25-41.10.1016/j.actamat.2017.12.033 ↗
22. D. Dyson and B. Holmes: J Iron Steel Inst 1970, vol. 208, pp. 469-474.
23. S.-J. Lee, S. Lee and B. C. De Cooman: Scripta Mater. 2011, vol. 64, pp. 649-652.10.1016/j.scriptamat.2010.12.012 ↗
24. Onink M, Brakman CM, Ticherlarr FD, Mittermeijer EJ, van der Zwaag S, Root JH, Konyer NB: Scr. Metall. Mater. 1993, vol. 29, pp. 1011-1016.10.1016/0956-716X(93)90169-S ↗
25. C.-M. Li, F. Sommer and E. J. Mittemeijer: Materials Science and Engineering: A 2002, vol. 325, pp. 307-319.10.1016/S0921-5093(01)01459-9 ↗
26. Y. Onuki, S. Sato, M. Nakagawa, K. Yamanaka, M. Mori, A. Hoshikawa, T. Ishigaki and A. Chiba: Quantum. Beam. Sci. 2018, vol. 2, p. 11.10.3390/qubs2020011 ↗
27. K. Sugimoto, M. Misu, M. Kobayashi and H. Shirasawa: ISIJ Int. 1993, vol. 33, pp. 775-782.10.2355/isijinternational.33.775 ↗
28. A. Zarei-Hanzaki, P. D. Hodgeson and S. Yue: ISIJ Int. 1995, vol. 35, pp. 79-85.10.2355/isijinternational.35.79 ↗