Superplastic Constitutive Equation Including Percentage of High-Angle Grain Boundaries as a Microstructural Parameter
Source abstract
Abstract
Fifteen Al-Mg-Sc samples with subgrain/grain sizes in the range of 1.8 to 4.9 μm were prepared through the processing methods of friction stir processing (FSP), equal-channel-angular pressing (ECAP), rolling, annealing, and combinations of the above. The percentages of high-angle grain boundaries (HAGBs) of these fine-grained alloys were distributed from 39 to 97 pct. The samples processed through FSP had a higher percentage of HAGBs compared to other samples. Superplasticity was achieved in all fifteen samples, but the FSP samples exhibited better superplasticity than other samples because their fine equiaxed grains, which were mostly surrounded by HAGBs, were conducive to the occurrence of grain boundary sliding (GBS) during superplastic deformation. The dominant deformation mechanism was the same for all fifteen samples, i.e., GBS controlled by grain boundary diffusion. However, the subgrains were the GBS units for the rolled or ECAP samples, which contained high percentages of unrecrystallized grains, whereas the fine grains were the GBS units for the FSP samples. Superplastic data analysis revealed that the dimensionless A in the classical constitutive equation for superplasticity of fine-grained Al alloys was not a constant, but increased with an increase in the percentage of HAGBs, demonstrating that the enhanced superplastic deformation kinetics can be ascribed to the high percentage of HAGBs. A modified superplastic constitutive equation with the percentage of HAGBs as a new microstructural parameter was established.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Microstructure and mechanical properties · Advanced Welding Techniques Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. Z.Y. Ma and R.S. Mishra: Friction Stir Superplasticity for Unitized Structures. ISBN: 978-0-12-420006-7, 2014, pp. 1–2.
2. [2] R.S. Mishra, T.R. Bieler and A.K. Mukherjee: Acta Mater., 1997, vol 45, pp 561-68.10.1016/S1359-6454(96)00194-2 ↗
3. [3] M. Mabuchi and K. Higashi: Int. J. Plast., 2001, vol. 17, pp. 399-407.10.1016/S0749-6419(00)00043-7 ↗
4. [4] A. Arieli and A.K. Mukherjee: Mater. Sci. Eng., 1980, vol. 45, pp 61-70.10.1016/0025-5416(80)90070-1 ↗
5. 5.T.G. Langdon: Acta. Metall. Mater., 1994, vol. 42, pp. 2437-43.10.1016/0956-7151(94)90322-0 ↗
6. R.S. Mishra, and Z.Y. Ma: Mater. Sci. Eng. R, 2005, vol. 50, pp. 1-78.10.1016/j.mser.2005.07.001 ↗
7. [7] R.Z. Valiev, R.K. Islamgaliev, and I.V. Alexandrov: Prog. Mat. Sci., 2000, vol. 45, pp. 103-89.10.1016/S0079-6425(99)00007-9 ↗
8. [8] J. Wang, Y. Iwahashi, Z. Horita, M. Furukawa, M. Nemoto, R.Z. Valiev, and T.G. Langdon: Acta Mater., 1996, vol. 44, pp. 2973-82.10.1016/1359-6454(95)00395-9 ↗
9. [9] N.A. Smirnova, V.I. Levit, V.I. Pilyugin, R.I. Kuznetsov, L.S. Davydova, and V.A. Sazonova: Fiz. Metal. Metall., 1986, vol. 61, pp. 1170-77.
10. [10] R. Kaibyshev, E. Avtokratova, A. Apollonov and R. Daives, Scripta Mater., 2006, vol. 54, 2119-24.10.1016/j.scriptamat.2006.03.020 ↗
11. [11] Z.Y. Ma, F.C. Liu, and R.S. Mishra: Acta Mater., 2010, vol. 58, pp 4693-704.10.1016/j.actamat.2010.05.003 ↗
12. [12] R.Z. Valiev, D.A. Salimonenko, N.K. Tsenev, P.B. Berbon, and T.G. Langdon: Scripta Mater., 1997, vol. 37, pp. 1945-50.10.1016/S1359-6462(97)00387-4 ↗
13. [13] F.C. Liu, Z.Y. Ma and L,Q.Chen: Scripta Mater., 2009, vol. 60, pp. 968-71.10.1016/j.scriptamat.2009.02.021 ↗
14. [14] J.N. Wang and Y. Wang: Int. J. Plast., 2006, vol. 22, pp. 1530-48.10.1016/j.ijplas.2005.10.003 ↗
15. [15] Z. Horita, M. Furukawa, M. Nemoto, A.J. Barnes and T.G. Langdon: Acta Mater. 2000, vol 48, pp. 3633-40.10.1016/S1359-6454(00)00182-8 ↗
16. [16] F.C. Liu and Z.Y. Ma: Scripta Mater. 2008, vol 59, pp. 882-885.10.1016/j.scriptamat.2008.06.035 ↗
17. [17] R. Kaibyshev, K. Shipilova, F. Musin and Y. Motohashi: Mater. Sci. Technol., 2005, vol. 21, pp. 408-418.10.1179/174328405X36610 ↗
18. [18] R.S. Mishra, M.W. Mahoney, S.X. McFadden, N.A. Mara and A.K. Mukherjee: Scripta Mater., 1999, vol. 42, pp. 163-68.10.1016/S1359-6462(99)00329-2 ↗
19. [19] Z.Y. Ma, R.S. Mishra, M.W. Mahoney and R. Grimes: Mater. Sci. Eng. A, 2003 vol 35, pp. 148-53.10.1016/S0921-5093(02)00824-9 ↗
20. [20] Z.Y. Ma, R.S. Mishra and M.W. Mahoney: Acta Mater., 2002, vol. 50, pp. 4419-30.10.1016/S1359-6454(02)00278-1 ↗
21. [21] Z.Y. Ma, R.S. Mishra, M.W. Mahoney and R. Grimes: Metall. Mater. Trans., 2005, vol. 36A, pp. 1447-58.10.1007/s11661-005-0237-6 ↗
22. [22] X.G. Jiang, J.Z. Cui and L.X. Ma: Acta Metall. Mater., 1993, vol. 41, pp. 2721-27.10.1016/0956-7151(93)90141-E ↗
23. [23] F.C. Liu, and Z.Y. Ma: J. Mater. Sci., 2009, vol. 44, pp. 2647-55.10.1007/s10853-009-3346-6 ↗
24. [24] F.C. Liu, and Z.Y. Ma: Mater. Sci. Eng. A, 2011, vol. 530, pp. 548-58.10.1016/j.msea.2011.10.018 ↗
25. [25] F.C. Liu, Z.Y. Ma, and F.C. Zhang: J. Mater. Sci Technol., 2012, vol. 28, pp. 1025-30.10.1016/S1005-0302(12)60168-6 ↗
26. [26]J.Q. Su, T.W. Nelson and C.J. Sterling: Philos. Mag., 2006, vol. 86, pp. 1-24.10.1080/14786430500267745 ↗
27. [27] M. Eddahbi, O.A. Ruano, T.R. McNelley: Metall. Mater. Trans., 2001, vol 32A, pp. 1093-102.10.1007/s11661-001-0120-z ↗
28. [28] T. McNelley, M. McMahon: Metall. Mater. Trans., 1997, vol 28A, pp. 1879-87.10.1007/s11661-997-0118-2 ↗
29. [29] O. Sitdikov, T. Sakai, E. Avtokratova, R. Kaibyshev, K. Tsuzaki and Y. Watanabe: Acta Mater., 2008, vol. 56, pp. 821-34.10.1016/j.actamat.2007.10.029 ↗
30. [30] O. Sitdikov, T. Sakai, E. Avtokratova, R. Kaibyshev, Y. Kimura and K. Tsuzaki: Mater. Sci. Eng. A, 2007, vol 444, pp. 18-30.10.1016/j.msea.2006.06.081 ↗
31. [31] F.J. Humphreys: J. Mater. Sci., 2001, vol. 36, pp. 3833-54.10.1023/A:1017973432592 ↗
32. [32] R.Z. Valiev and T.G. Langdon: Prog. Mater. Sci., 2006, vol. 51, pp. 881-981.10.1016/j.pmatsci.2006.02.003 ↗
33. [33] J.K. Mackenzie: Biometrica, 1958 vol. 45, pp. 229-40.10.1093/biomet/45.1-2.229 ↗
34. [34] M. Ferry and N. Burhan: Acta Mater., 2007, vol. 55, pp. 3479-91.10.1016/j.actamat.2007.01.047 ↗
35. [35] S. Komura, P.B. Berbon, M. Furukawa, Z. Horita, M. Nemoto and T.G. Langdon: Scripta Mater. 1998, vol. 38, pp. 1851-56.10.1016/S1359-6462(98)00099-2 ↗
36. [36] P.S. Bate, N. Ridley and B. Zhang: Acta Mater., 2007, vol. 55, 4995-5006.10.1016/j.actamat.2007.05.017 ↗
37. [37] P.S. Bate, F.J. Humphreys, N. Ridley and B. Zhang: Acta Mater., 2005, vol. 53, 3059-69.10.1016/j.actamat.2005.03.019 ↗
38. [38] F.C. Liu, P. Xue and Z.Y. Ma: Mater. Sci. Eng. A, 2012, vol. 547, pp. 55-63.10.1016/j.msea.2012.03.076 ↗
39. [39] J. Liu and D.J. Chakrabarti: Acta Mater. 1996, vol. 44, 4647-61.10.1016/S1359-6454(96)00141-3 ↗
40. [40] T.G. Nieh, L.M. Hsiung, J. Wadsworth and R. Kaibyshev: Acta Mater., 1998, vol. 46, pp. 2789-800.10.1016/S1359-6454(97)00452-7 ↗
41. [41] X.Y. Yang, H. Miura and T. sakai: Mater. Trans. 2002, vol. 43, pp. 2400-07.10.2320/matertrans.43.2400 ↗
42. [42] E.W. Lee and T.R. McNelley: Mater. Sci. Eng., 1987 vol. 93, pp. 45-55.10.1016/0025-5416(87)90411-3 ↗
43. [43] L.B. Johannes and R.S. Mishra: Mater. Sci. Eng. A, 2007, vol.464, pp 255-60.10.1016/j.msea.2007.01.141 ↗
44. [44] P. Lagard and M. Biscondi: Can. Metal. Q., 1974, vol. 13, pp245-51.10.1179/cmq.1974.13.1.245 ↗
45. [45] S.J. Hales and T.R. McNelley: Acta Metall. 1988, vol. 36, pp. 1229-39.10.1016/0001-6160(88)90275-1 ↗
46. [46] H. Gudmundsson, D. Brooks and J.A. Wert: Acta Metall. Mater. 1991, vol 39, pp. 19-35.10.1016/0956-7151(91)90325-U ↗