journal article·2014-09

Texture Development in a Friction Stir Lap-Welded AZ31B Magnesium Alloy

B. S. Naik, D. L. Chen, X. Cao, P. Wanjara

Publisher page

Abstract

The present study was aimed at characterizing the microstructure, texture, hardness, and tensile properties of an AZ31B-H24 Mg alloy that was friction stir lap welded (FSLWed) at varying tool rotational rates and welding speeds. Friction stir lap welding (FSLW) resulted in the presence of recrystallized grains and an associated hardness drop in the stir zone (SZ). Microstructural investigation showed that both the AZ31B-H24 Mg base metal (BM) and SZ contained β-Mg17Al12 and Al8Mn5 second phase particles. The AZ31B-H24 BM contained a type of basal texture (0001)〈11 $$ \overline{2} $$ 0〉 with the (0001) plane nearly parallel to the rolled sheet surface and 〈11 $$ \overline{2} $$ 0〉 directions aligned in the rolling direction. FSLW resulted in the formation of another type of basal texture (0001)〈10 $$ \overline{1} $$ 0〉 in the SZ, where the basal planes (0001) became slightly tilted toward the transverse direction, and the prismatic planes (10 $$ \overline{1} $$ 0) and pyramidal planes (10 $$ \overline{1} $$ 1) exhibited a 30 deg + (n − 1) × 60 deg rotation (n = 1, 2, 3, …) with respect to the rolled sheet normal direction, due to the shear plastic flow near the pin surface that occurred from the intense local stirring. With increasing tool rotational rate and decreasing welding speed, the maximum intensity of the basal poles (0001) in the SZ decreased due to a higher degree of dynamic recrystallization that led to a weaker or more random texture. The tool rotational rate and welding speed had a strong effect on the failure load of FSLWed joints. A combination of relatively high welding speed (20 mm/s) and low tool rotational rate (1000 rpm) was observed to be capable of achieving a high failure load. This was attributed to the relatively small recrystallized grains and high intensity of the basal poles in the SZ arising from the low heat input as well as the presence of a small hooking defect.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (68)

Show source-provided references
1. T.M. Pollock: Science, 2010, vol. 328, pp. 986–87.10.1126/science.1182848 ↗
2. S.J. Davis, K. Caldeira, H.D. Matthews: Science, 2010, vol. 329, pp. 1330–33.10.1126/science.1188566 ↗
3. M. Wise, K. Calvin, A. Thomson, L. Clarke, B. Bond-Lamberty, R. Sands, S.J. Smith, A. Janetos, J. Edmonds: Science, 2009, vol. 324, pp. 1183–86.10.1126/science.1168475 ↗
4. W.G. Agnew: Science, 1974, vol. 183, pp. 254–56.10.1126/science.183.4122.254 ↗
5. L.R. Kump: Nature, 2002, vol. 419, pp. 188–90.10.1038/nature01087 ↗
6. J. Murray, D. King: Nature, 2012, vol. 481, pp. 433–35.10.1038/481433a ↗
7. D.A. Howey: Nat. Clim. Change, 2012, vol. 2, pp. 28–29.10.1038/nclimate1336 ↗
8. D. Shindell, G. Faluvegi, M. Walsh, S.C. Anenberg, R.V. Dingenen, N.Z. Muller, J. Austin, D. Koch, G. Milly: Nat. Clim. Change, 2011, vol. 1, pp. 59–66.10.1038/nclimate1066 ↗
9. H.J. Kim, G.A. Keoleian, S.J. Skerlos: J. Ind. Ecol., 2011, vol. 15, pp. 64–80.10.1111/j.1530-9290.2010.00288.x ↗
10. H.J. Kim, C. McMillan, G.A. Keoleian, S.J. Skerlos: J. Ind. Ecol., 2010, vol. 14, pp. 929–46.10.1111/j.1530-9290.2010.00283.x ↗
11. S. Begum, D.L. Chen, S. Xu, A.A. Luo: Mater. Sci. Eng. A, 2009, vol. A517, pp. 334–43.10.1016/j.msea.2009.04.051 ↗
12. J.F. Nie, Y.M. Zhu, J.Z. Liu, X.Y. Fang: Science, 2013, vol. 340, pp. 957–60.10.1126/science.1229369 ↗
13. Q. Yu, J. Zhang, Y. Jiang, Q. Li: Int. J. Fatigue, 2011, vol. 33, pp. 437–47.10.1016/j.ijfatigue.2010.09.020 ↗
14. Q. Yu, J. Zhang, Y. Jiang, Q. Li: Int. J. Fatigue, 2012, vol. 36, pp. 47–58.10.1016/j.ijfatigue.2011.08.016 ↗
15. J.B. Jordon, J.B. Gibson, M.F. Horstemeyer, H.E. Kadiri, J.C. Baird, A.A. Luo: Mater. Sci. Eng. A, 2011, vol. 528, pp. 6860–71.10.1016/j.msea.2011.05.047 ↗
16. X. Cao, M. Jahazi: Mater. Des, 2009, vol. 30, pp. 2033–42.10.1016/j.matdes.2008.08.040 ↗
17. N. Afrin, D.L. Chen, X. Cao, M. Jahazi: Mater. Sci. Eng. A, 2008, vol. 472, pp. 179–86.10.1016/j.msea.2007.03.018 ↗
18. H.B. Chen, K. Yan, T. Lin, S.B. Chen, C.Y. Jiang, Y. Zhao: Mater. Sci. Eng. A, 2006, vol. 433, pp. 64–9.10.1016/j.msea.2006.06.056 ↗
19. R.S. Mishra, Z.Y. Ma: Mater. Sci. Eng. R, 2005, vol. 50, pp. 1–78.10.1016/j.mser.2005.07.001 ↗
20. S.H. Chowdhury, D.L. Chen, S.D. Bhole, X. Cao, P. Wanjara: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 323–36.10.1007/s11661-012-1382-3 ↗
21. S.H. Chowdhury, D.L. Chen, S.D. Bhole, X. Cao, P. Wanjara: Mater. Sci. Eng. A, 2012, vol. 556, pp. 500–509.10.1016/j.msea.2012.07.019 ↗
22. C. Liu, D.L. Chen, S. Bhole, X. Cao, M. Jahazi: Mater. Charact., 2009, vol. 60, pp. 370–76.10.1016/j.matchar.2008.10.009 ↗
23. S.M. Chowdhury, D.L. Chen, S.D. Bhole, X. Cao, E. Powidajko, D.C. Weckman, Y. Zhou: Mater. Sci. Eng. A, 2010, vol. 527(12), pp. 2951–61.10.1016/j.msea.2010.01.031 ↗
24. A.W. Tayon, S.M. Domack, K.E. Hoffman, and S.J. Hales: Metall. Mater. Trans. A, 2013, Vol. 44A, pp. 4906–913.10.1007/s11661-013-1802-z ↗
25. X. Cao and M. Jahazi: Proceedings of the 8th International Conference on “Trends in Welding Research”, S.A. David, T. DebRoy, J.N. DuPont, T. Koseki, and H.B. Smart, eds., ASM International, Materials Park, OH, 2009.
26. B.S. Naik, D.L. Chen, X. Cao, P. Wanjara: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 3732–46.10.1007/s11661-013-1728-5 ↗
27. S.H.C. Park, Y.S. Sato, H. Kokawa: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 987-94.10.1007/s11661-003-0228-4 ↗
28. C.I. Chang, C. J. Lee, J.C. Huang: Scripta Mater., 2004, vol. 51, pp. 509–14.10.1016/j.scriptamat.2004.05.043 ↗
29. W. Woo, H. Choo, D.W. Brown, P.K. Liaw, Z. Feng, M.B. Prime, Z. Feng: Scripta Mater., 2006, vol. 54, pp. 1859–64.
30. R. Fonda and J. Bingert: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 1487–99.10.1007/s11661-004-0257-7 ↗
31. D. Field, T. Nelson, Y. Hovanski, and K. Jata: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 2869–77.10.1007/s11661-001-1037-2 ↗
32. F. Bachmann, R. Hielscher, H. Schaeben: Trans. Tech. Publ., 2010, vol. 160, pp 63–8.
33. ASTM International Standard ASTM D3164-03: Standard Test Method for Strength Properties of Adhesively Bonded Lap-Shear Sandwich Joints in Shear by Tensile Loading, 2003.
34. N. Afrin, D.L. Chen, X. Cao, M. Jahazi: Scripta Mater., 2007, vol. 57, pp. 1004–07.10.1016/j.scriptamat.2007.08.001 ↗
35. M. Fairman, N. Afrin, D.L. Chen, X.J. Cao, M. Jahazi: Can. Metall. Quart., 2007, vol. 46, pp. 425–32.10.1179/cmq.2007.46.4.425 ↗
36. M. Ohno, R. Schmid-Fetzer: Z. Metallkd., 2005, vol. 96, pp. 857–69.10.3139/146.101125 ↗
37. C.Y. Liu, R. Jing, Q. Wang, B. Zhang, Y.Z. Jia, M.Z. Ma, R.P. Liu: Mater. Sci. Eng. A, 2012, vol. 558, pp. 510–16.10.1016/j.msea.2012.08.037 ↗
38. J. Yan, Z. Xu, Z. Li, L. Li, S. Yang: Scripta Mater., 2005, vol. 53, pp. 585–89.10.1016/j.scriptamat.2005.04.022 ↗
39. L. Xiao, L. Liu, Y. Zhou, S. Esmaeili: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 1511–22.10.1007/s11661-010-0197-3 ↗
40. G. Gottstein, T. Al-Samman: Mater. Sci. Forum, 2005, vol. 495–97, pp. 623–32.10.4028/www.scientific.net/MSF.495-497.623 ↗
41. Y.N. Wang, J.C. Huang: Mater. Chem. Phys., 2003, vol. 81, pp. 11–26.10.1016/S0254-0584(03)00168-8 ↗
42. D.Sarker, D.L.Chen: Mater. Sci. Eng. A, 2013, vol. 582, pp. 63–7.10.1016/j.msea.2013.06.048 ↗
43. T.Al-Samman, G. Gottstein: Mater. Sci. Eng. A, 2008, vol. 488, pp. 406–414.10.1016/j.msea.2007.11.056 ↗
44. I. Ulacia, S. Yi, M.T. Perez-Prado, N.V. Dudamell, F. Galvez, D. Letzig, and I. Hurtado: Proc. 4th Inter. Conf. on High Speed forming, Columbus, OH, 2010, March 9–10, pp. 189–97.
45. K.U. Kainer: Proc. 7th Inter. Conf. on Magnesium Alloys and Their Application, Dresden, Germany, 2006, November 6–9, pp. 161–63.
46. X. Li, F. Jiao, T. Al-Samman, S.G. Chowdhury: Scripta Mater., 2012, vol. 66, pp. 159–62.10.1016/j.scriptamat.2011.10.028 ↗
47. X. Li, T. Al-Samman, S. Mu, G. Gottstein: Mater. Sci. Eng. A, 2012, vol. 528, pp. 7915–25.10.1016/j.msea.2011.07.010 ↗
48. J. Hirsch, T. Al-Samman: Acta Mater., 2013, vol 61, pp. 818–43.10.1016/j.actamat.2012.10.044 ↗
49. A. Couret, D. Caillard: Acta. Metall., 1985, vol. 33, pp. 1447–54.10.1016/0001-6160(85)90045-8 ↗
50. L. Helis, K. Okayasu, H. Fukutomi: Mater. Sci. Eng. A, 2006, vol. 430, pp. 98–103.10.1016/j.msea.2006.04.125 ↗
51. H.T. Jeong, T.K. Ha: J. Mater. Process. Technol., 2007, vol. 187–188, pp. 559–61.10.1016/j.jmatprotec.2006.11.084 ↗
52. R.W. Fonda, K.E. Knipling: Sci. Technol. Weld. Joining, 2011, vol. 16, pp. 288–94.10.1179/1362171811Y.0000000010 ↗
53. H.W. Lee, T.S. Lui, L.H. Chen: J. Alloys Compd., 2009, vol. 475, pp. 139–44.10.1016/j.jallcom.2008.07.010 ↗
54. S.H.C. Park, Y.S. Sato, H. Kokawa: Scripta Mater., 2003, vol. 49, pp. 161–66.10.1016/S1359-6462(03)00210-0 ↗
55. V.K. Patel, S.D. Bhole, D.L. Chen: Mater. Sci. Eng. A, 2013, vol. 569, pp. 78–85.10.1016/j.msea.2013.01.042 ↗
56. F.A.Mirza, D.L.Chen, D.J.Li, X.Q.Zeng: Mater. Sci. Eng. A, 2013, vol. 575, pp. 65–73.10.1016/j.msea.2013.03.041 ↗
57. F.A. Mirza, D.L. Chen, D.J. Li, X.Q. Zeng: Mater. Des., 2013, vol. 46, pp. 411–18.10.1016/j.matdes.2012.10.040 ↗
58. C.L. Fan, D.L. Chen, A.A. Luo: Mater. Sci. Eng. A, 2009, vol. A519, pp. 38–45.10.1016/j.msea.2009.04.048 ↗
59. X.Z. Lin, D.L. Chen: J. Mater. Eng. Perform., 2008, vol. 17, pp. 894–901.10.1007/s11665-008-9247-z ↗
60. E. Schmid, Z. Electrochem., 1931, Vol. 37, pp. 447.
61. M.R. Barnett: Mater. Sci. Eng. A, 2007, vol. 464, pp. 8–16.10.1016/j.msea.2007.02.109 ↗
62. C. Yan, W. Ma, V. Burg, M.W. Chen: J. Mater. Sci., 2007, vol. 42, pp. 7702–07.10.1007/s10853-007-1674-y ↗
63. P. Cizek, M.R. Barnett: Scripta Mater., 2006, vol. 55, pp. 915–18.10.1016/j.scriptamat.2006.07.036 ↗
64. Z. Keshavarz, M.R. Barnett: Scripta Mater., 2008, vol. 59, pp. 959–62.10.1016/j.scriptamat.2008.06.041 ↗
65. F.A. Mirza and D.L. Chen: in Aerospace Materials Handbook, S. Zhang and D.L. Zhao, eds., CRC Press/Taylor & Francis Group, Boca Raton, FL, 2013, pp. 647–98.
66. Y.N. Wang, J.C. Huang: Acta Mater., 2007, vol. 55, pp. 897–905.10.1016/j.actamat.2006.09.010 ↗
67. X. Li, T. Al-Samman, S. Mu, G. Gottstein: Mater. Sci. Eng. A, 2011, vol. 528, pp. 7915–925.10.1016/j.msea.2011.07.010 ↗
68. D. Sarker, D.L. Chen: Mater. Sci. Eng. A, 2014, vol. 596, pp. 134–44.10.1016/j.msea.2013.12.038 ↗