journal article·2013-11

Effect of Aging Treatment on Fatigue Behavior of an Al-Cu-Mg-Ag Alloy

M. E. Burba, M. J. Caton, S. K. Jha, C. J. Szczepanski

Publisher page

Abstract

An investigation of the fatigue properties of an Al-Cu-Mg-Ag alloy with two different heat treatments—peak aged (T6), and peak aged interrupted (T6I4)—has been conducted. While the strength levels resulting from the two heat treatments were similar, the main difference between the microstructures was that the peak aged interrupted material contained a higher volume fraction of the θ′ precipitates. This study specifically focused on the effects of these treatments on the fatigue lifetime distribution, and the role of crack initiation vs the small crack growth behavior. Several total fatigue lifetime tests were completed at room temperature and at a given stress level to characterize the distribution in fatigue lifetimes. Fatigue results indicate that there is almost no difference in the mean lifetime for either heat treatment, but there is a significant difference in the minimum lifetimes, where the peak aged condition exhibited a higher propensity for life-limiting failure mechanisms. The small crack growth behavior of the two aging treatments was studied both at room temperature and elevated temperature by means of a standard acetate replication method. The small crack growth rates at both temperatures were largely unaffected by the different aging treatments. Based on the given number of tests, results suggest that the life-limiting fatigue failures of the two aging treatments are primarily governed by different crack initiation mechanisms due to the differences seen in the density of θ′ precipitates.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. I. J. Polmear, G. Pons, Y. Barbaux, H. Octor, C. Sanchez, A. J. Morton, W. E. Borbidge, and S. Rogers: Materials Science and Technology, 1999, vol. 15, pp. 861-868.10.1179/026708399101506599 ↗
2. R. N. Lumley, A. J. Morton, and I. J. Polmear: Acta Materialia, 2002, vol. 50, pp. 3597-608.10.1016/S1359-6454(02)00164-7 ↗
3. R.N. Lumley, I.J. Polmear, and A.J. Morton: Mater. Sci. Technol., 2005, vol. 219, pp. 1025–32.10.1179/174328405X51875 ↗
4. T. Broom, J.H. Molineux, and V.N. Wittaker: J. Inst. Met., 1955-56, vol. 84, pp. 357–63.
5. C.A. Stubbington: Royal Aircraft Establishment, Technical Note No. Met. 279, Farnborough, UK, 1957.
6. G. W. Form: Transactions of the ASM, 1960, vol. 52, pp. 514-527.
7. W.G. Fricke, Jr.: Trans. ASM, 1960, vol. 52, pp. 527-529.
8. C. A. Stubbington: Metallurgia, 1963, vol. 68, pp.109-121.
9. J.M. Finney: Aeronautical Research Laboratories Structures and Materials, Report no. 325, Melbourne, Australia, 1969.
10. R.J.H. Wanhill: Fatigue Crack Initiation in Aerospace Aluminium Alloys, Components and Structures, Technical no. NLR-TP-2006-751, Noordwijk, Netherlands, 2007.
11. R. N. Lumley, R. G. O’Donnell, I. J. Polmear, and J. R. Griffiths: Materials Forum, 2005, vol. 29, pp. 256-61.
12. L. Yan, F.-S. Du, S.-L. Dai, and S.-J. Yang: J. Cent. South Univ. Technol., 2010, vol. 17, pp. 697–702.10.1007/s11771-010-0542-0 ↗
13. G. H. Bray, M. Glazov, R. J. Rioja, D. Li, and R. P. Gangloff: International Journal of Fatigue, 2001, vol. 23, pp. 265-76.10.1016/S0142-1123(01)00159-1 ↗
14. L. Yanbin, L. Zhiyi, L. Yuntao, X. Qinkun, and Z. Jie: Mater. Sci. Eng. A, 2008, vol. 4921–2, pp. 333–36.10.1016/j.msea.2008.03.045 ↗
15. S. K. Jha, M. J. Caton, and J. M. Larsen: Materials Science and Engineering: A, 2007, vol. 468-470, pp. 23-32.10.1016/j.msea.2006.10.171 ↗
16. W.J. Porter III, K. Li, M.J. Caton, S.K. Jha, B.B. Bartha, and J.M. Larsen: Superalloys 2008. TMS, Warrendale, PA, 2008, pp. 541–48.
17. S.K. Jha, M.J. Caton, and J.M. Larsen: Superalloys 2008, TMS, Warrendale, PA, 2008, pp. 565–72.
18. S.K. Jha, J.M. Larsen, and A.H. Rosenberger: Eng. Fract. Mech., 2009, vol. 76.5, pp. 681–94.10.1016/j.engfracmech.2008.10.013 ↗
19. K. O. Pedersen, O. G. Lademo, T. Berstad, T. Furu, and O. S. Hopperstad: Journal of Materials Processing Technology, 2008, vol. 200, pp. 77-93.10.1016/j.jmatprotec.2007.08.040 ↗
20. N. Nanninga and C. White: Int. J. Fatigue, 2009, vol. 31.7, pp. 1215–24.10.1016/j.ijfatigue.2008.11.015 ↗
21. R.N. Lumley and I.J. Polmear: Scripta Mater., 2004, vol. 509, pp. 1227–31.10.1016/j.scriptamat.2004.02.001 ↗
22. J.M. Larsen, J.R. Jira, and K.S. Ravichandran: Small Crack Test Methods, ASTM STP No. 1149, 1992, pp. 57–80.10.1520/STP1149-EB ↗
23. X. Zhu. Ph.D. Dissertation, University of Michigan, Ann Arbor, MI, 2007.
24. K. Pedersen, O. Helgeland, and O. Lohne: Fracture and the Role of Microstructure, Vol. 2, Engineering Materials Advisory Services Limited, Leoben, Austria, 1982, pp. 495-500.
25. N. Kamp, N. Gao, M. J. Starink, and I. Sinclair: International Journal of Fatigue, 2007, vol. 29, pp. 869-78.10.1016/j.ijfatigue.2006.08.005 ↗
26. J.C. Newman Jr., and I.S. Raju: Eng. Fract. Mech., 1981, vol. 151-2, pp. 185–92.10.1016/0013-7944(81)90116-8 ↗
27. A. Sugeta, Y. Uematsu, M. Yasuda, and M. Jono: J. Soc. Mater. Sci. Jpn., 2006, vol. 556, pp. 545–49.10.2472/jsms.55.545 ↗