journal article·2017-03

Role of Tungsten in the Tempered Martensite Embrittlement of a Modified 9 Pct Cr Steel

Alexandra Fedoseeva, Nadezhda Dudova, Rustam Kaibyshev

Publisher page

Abstract

The effect of tempering on the mechanical properties and fracture behavior of two 3 pct Co-modified 9 pct Cr steels with 2 and 3 wt pct W was examined. Both steels were ductile in tension tests and tough under impact tests in high-temperature tempered conditions. At T ≤ 923 K (650 °C), the addition of 1 wt pct W led to low toughness and pronounced embrittlement. The 9Cr2W steel was tough after low-temperature tempering up to 723 K (450 °C). At 798 K (525 °C), the decomposition of retained austenite induced the formation of discontinuous and continuous films of M23C6 carbides along boundaries in the 9Cr2W and the 9Cr3W steels, respectively, which led to tempered martensite embrittlement (TME). In the 9Cr2W steel, the discontinuous boundary films played a role of crack initiation sites, and the absorption energy was 24 J cm−2. In the 9Cr3W steel, continuous films provided a fracture path along the boundaries of prior austenite grains (PAG) and interlath boundaries in addition that caused the drop of impact energy to 6 J cm−2. Tempering at 1023 K (750 °C) completely eliminated TME by spheroidization and the growth of M23C6 carbides, and both steels exhibited high values of adsorbed energy of ≥230 J cm−2. The addition of 1 wt pct W extended the temperature domain of TME up to 923 K (650 °C) through the formation of W segregations at boundaries that hindered the spheroidization of M23C6 carbides.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (44)

Show source-provided references
1. F. Abe, T.U. Kern, R. Viswanathan: Creep resistant steels, Woodhead Publishing in Materials, Cambridge, England, 2008, pp. 174-212.10.1533/9781845694012 ↗
2. R.O. Kaybyshev, V.N. Skorobogatykh, I.A. Shchenkova: Phys. Met. Metall., 2010, vol. 109, pp. 186–200.10.1134/S0031918X10020110 ↗
3. K. L. Murty, I. Charit: J. Nucl. Mater., 2008, vol. 383, pp. 189–195.10.1016/j.jnucmat.2008.08.044 ↗
4. J. S. Cheon, Ch. B. Lee, B. O. Lee, J.P. Raison, T. Mizuno, F. Delage, J. Carmack: J. Nucl. Mater., 2009, vol. 392, pp. 324–330.10.1016/j.jnucmat.2009.03.021 ↗
5. W. Wang, W. Yan, W. Sha, Y. Shan, K. Yang: Metall. Mater. Trans. A, 2012, vol.43, pp. 4113-22.10.1007/s11661-012-1240-3 ↗
6. A.Yu. Kipelova, A.N. Belyakov, V.N. Skorobogatykh, I.A. Shchenkova, R.O. Kaibyshev: Met. Sci. Heat Treat., 2010, vol. 52, pp. 100–110.10.1007/s11041-010-9240-7 ↗
7. N. Dudova, R. Mishnev, R. Kaibyshev: ISIJ Int., 2011, vol. 51, pp. 1912-18.10.2355/isijinternational.51.1912 ↗
8. I. Fedorova, A. Kostka, E. Tkachev, A. Belyakov, R. Kaibyshev: Mater. Sci. Eng. A, 2016, vol. 662, pp. 443–455.10.1016/j.msea.2016.03.092 ↗
9. A. Fedoseeva, N. Dudova, R. Kaibyshev: J. Mat. Sci. 2016, vol. 51, pp. 9424-39.10.1007/s10853-016-0188-x ↗
10. G. Krauss: Steels: Processing, Structure, and Performance, USA, ASM International, 2005, pp.327-416.
11. H.K.D.H. Bhadeshia, R. Honeycombe: Steels: Microstructure and Properties, third ed., Butterworth-Heinemann, UK, 2006, pp. 235-58.10.1016/B978-075068084-4/50013-3 ↗
12. G.V. Prabhu Gaunkar, A. M. Huntz, and P. Lacombe: Met. Sci., 1980, pp. 241–52.10.1179/030634580790426427 ↗
13. F. Christien, R. Le Gall, G. Saindrenan: Scr. Mater., 2003, vol. 48, pp. 11-16.10.1016/S1359-6462(02)00309-3 ↗
14. F. Christien, R. Le Gall, G. Saindrenan: Metall. Mater. Trans. A, 2003, vol.34, pp.2483-2491.10.1007/s11661-003-0008-1 ↗
15. M. Jafari, K. Tsuzaki: J. Alloys Compd., 2013, vol. 577S, pp. S636–S641.10.1016/j.jallcom.2012.03.031 ↗
16. S. Sathyanarayanan, J. Basu, A. Moitra, G. Sasikala, V. Singh: Metall. Mater. Trans. A, 2013, vol. 44, pp.2141-55.10.1007/s11661-012-1510-0 ↗
17. W. Zhong, W. Wang, X. Yang, W. Li, W. Yan, W. Sha, W. Wang,. Y. Shan, K. Yang: Mater. Sci. Eng. A: 2015, vol. 639, pp. 252–8.10.1016/j.msea.2015.05.012 ↗
18. P. Yan, Zh. Liu, H. Bao, Y. Weng, W. Liu: Mater. Des., 2014, vol. 54, pp. 874–879.10.1016/j.matdes.2013.09.017 ↗
19. L. Schäfer: J. Nucl. Mater., 2000, vol. 283–287, pp. 707–710.10.1016/S0022-3115(00)00115-X ↗
20. W. Zhong, W. Wang, X. Yang, W. Li, W. Yan, W. Sha, W. Wang, Y. Shan, Ke Yang: Mater. Sci. Eng. A, 2015, vol. 639, pp. 252–258.10.1016/j.msea.2015.05.012 ↗
21. J. Blach, L. Falat, P. Ševc: Eng. Failure Anal., 2009, vol. 16, pp. 1397–1403.10.1016/j.engfailanal.2008.09.003 ↗
22. R.L. Klueh, M.A. Sokolov, K. Shiba, Y. Miwa, J.P. Robertson: J. Nucl. Mater., 2000, vol. 283-287, pp. 478-482.10.1016/S0022-3115(00)00086-6 ↗
23. H.-C. Schneider, B. Dafferner, J. Aktaa: J. Nucl. Mater., 2003, vol. 321, pp. 135–140.10.1016/S0022-3115(03)00241-1 ↗
24. X. Hu, L. Huang, W. Yan, W. Wang W. Sha, Y. Shan, Ke Yang: Mater. Sci. Eng. A, 2013, vol. 586, pp. 253–258.10.1016/j.msea.2013.08.025 ↗
25. F. Lu, P. Liu, H. Ji, Y. Ding, X. Xu, and Y. Gao: Mater. Char., 2014, vol. 92, pp. 149–158.10.1016/j.matchar.2014.03.014 ↗
26. R.K. Shiue, K.C. Lan, C. Chen: Mater. Sci. Eng. A, 2000, vol. 287, pp. 10–16.10.1016/S0921-5093(00)00831-5 ↗
27. A. Kipelova, A. Belyakov, R. Kaibyshev: Mater. Sci. Eng. A 2012, vol. 532, pp. 71–77.10.1016/j.msea.2011.10.064 ↗
28. A. Fedoseeva, N. Dudova, R. Kaibyshev: Mater. Sci. Eng. A, 2016, vol. 654, pp. 1–12.10.1016/j.msea.2015.12.027 ↗
29. N. Dudova, A. Plotnikova, D. Molodov, A. Belyakov, R. Kaibyshev: Mater. Sci. Eng. A 2012, vol.534, pp. 632–9.10.1016/j.msea.2011.12.020 ↗
30. L. Helis, Y. Toda, T. Hara, H. Miyazaki, F. Abe: Mater. Sci. Eng. A, 2009, vol. 510-511, pp. 88–94.10.1016/j.msea.2008.04.131 ↗
31. P. Yan, Zh. Liu: Mater. Sci. Eng. A, 2016, vol. 650, pp. 290–4.10.1016/j.msea.2015.09.115 ↗
32. Y. Liu, S. Tsukamoto, K. Sawada, F. Abe: Metall. Mater. Trans. A, 2015, vol. 45, pp. 1306–1314.
33. Y. Liu, S. Tsukamoto, K. Sawada, M. Tabuchi, F. Abe: Metall. Mater. Trans. A, 2015, vol. 46, pp. 1843–1854.10.1007/s11661-015-2802-y ↗
34. S.G. Hong, W.B. Lee, C.G. Park: Scr. Mater., 2000, vol. 43, pp. 181–6.10.1016/S1359-6462(00)00389-4 ↗
35. F. Abe, T. Noda, H. Araki, S. Nakazawa: J. Nucl. Mater., 1991, vol. 179-181, pp. 663-6.10.1016/0022-3115(91)90176-8 ↗
36. H.K. Danielsen, P.E. Di Nunzio, J. Hald: Metall. Mater. Trans. A 2013, vol. 44, pp. 2445-52.10.1007/s11661-012-1583-9 ↗
37. R. Chaouadi, and A. Fabry: in From Charpy to Present Impact Testing, D. Francois, and A. Pineau, eds., Elsevier Science Ltd. and ESIS, Oxford, UK, 2002, pp. 103–17.10.1016/S1566-1369(02)80011-5 ↗
38. ASM Handbook, Fractography, ASM International Materials Park, OH, 1987, vol. 12.
39. E. El-Kashif, K. Asakura, T. Koseki, K. Shibata: ISIJ Int., 2004, Vol. 44, pp. 1568–75.10.2355/isijinternational.44.1568 ↗
40. H. Yan, H. Bib, X. Lib, Zh. Xua: Mater. Char., 2008, vol. 59, pp. 1741-46.10.1016/j.matchar.2008.03.018 ↗
41. ASM Handbook, Mechanical Testing and Evaluation, ASM International Materials Park, OH, 2000, vol. 8.
42. F. Zia-Ibrahimi, G. Krauss: Metall. Trans. A, 1983, vol. 14A, pp. 1109-19.10.1007/BF02670449 ↗
43. Y. Kimura, T. Inoue, F. Yin, K. Tsuzaki: Science, 2008, vol. 320, pp. 1057-58.10.1126/science.1156084 ↗
44. E. Wakai, N. Okubo, M. Ando, T. Yamamoto, and F. Takada: J. Nucl. Mater., 210, vol. 398, pp. 64–67.10.1016/j.jnucmat.2009.10.011 ↗