Nitride Formation and Excess Nitrogen Uptake After Nitriding Ferritic Fe-Ti-Cr Alloys
Source abstract
Abstract
The microstructure of the nitrided zone of Fe-Ti-Cr alloys, containing a total of 0.30 at. pct (Ti + Cr) alloying elements, with varying Ti/Cr atomic ratio (0.45, 0.87, and 1.90), was investigated by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The stable TiN and CrN nitrides did not precipitate after nitriding. Instead, ultrafine, metastable, mixed Ti1–x Cr x N nitride precipitates developed in the nitrided zone: The precipitates were of platelet morphology (length ≤30 nm and thickness ≤3 nm) and of cubic, rock-salt, crystal-structure type. The misfit strain around the nitride platelets in the ferrite matrix increases with increasing Ti/Cr atomic ratio. As a consequence, most pronouncedly for the highest Ti/Cr atomic ratio, a tetragonally distorted ferrite matrix surrounds the precipitates, as evidenced both by XRD and TEM. The amount of nitrogen taken up was determined quantitatively by measuring the so-called nitrogen-absorption isotherms. It follows that the absorbed amount of so-called excess nitrogen dissolved in the matrix and adsorbed at the nitride-platelet faces increases distinctly with increasing Ti/Cr atomic ratio. The results were discussed in terms of the dependence of misfit strain on the Ti/Cr atomic ratio and the higher chemical affinity of Ti for N than of Cr for N.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Intermetallics and Advanced Alloy Properties · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. S. Lampman: Introduction to Surface Hardening of Steel, ASM Handbook, vol. 4, Heat Treating, ASM International, Metals Park, OH, 1991, pp. 259-67.
2. E.J. Mittemeijer and J.T. Slycke: Surf. Eng., 1996, vol. 12, pp. 152-62.10.1179/sur.1996.12.2.152 ↗
3. E.J. Mittemeijer and M.A.J. Somers: Surf. Eng., 1997, vol. 13, pp. 483-97.10.1179/sur.1997.13.6.483 ↗
4. E.J. Mittemeijer: J. Metal., 1985, vol. 37, pp. 16-20.
5. E.J. Mittemeijer: Mater. Sci. Forum, 1992, vols. 102–104, pp. 223-28.
6. P.M. Hekker, H.C.F. Rozendaal, and E.J. Mittemeijer: J. Mater. Sci., 1985, vol. 20, pp. 718-29.10.1007/BF01026547 ↗
7. R.E. Schacherl, P.C.J. Graat, and E.J. Mittemeijer: Z. Metallkd., 2002, vol. 93, pp. 468-77.10.3139/146.020468 ↗
8. R.E. Schacherl, P.C.J. Graat, and E.J. Mittemeijer: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 3387-98.10.1007/s11661-004-0175-8 ↗
9. B. Mortimer, P. Grieveson, and K.H. Jack: Scand. J. Metals, 1972, vol. 1, pp. 203-09.
10. S.S. Hosmani, R.E. Schacherl, and E.J. Mittemeijer: Mater. Sci. Technol., 2005, vol. 21, pp. 113-24.10.1179/174328405X16289 ↗
11. S.S. Hosmani, R.E. Schacherl, and E.J. Mittemeijer: J. Mater. Sci., 2008, vol. 43, pp. 2618-24.10.1007/s10853-008-2473-9 ↗
12. M.H. Biglari, C.M. Brakman, E.J. Mittemeijer, and S. van der Zwaag: Phil. Mag. A, 1995, vol. 72, pp. 931-47.10.1080/01418619508239945 ↗
13. M.H. Biglari, C.M. Brakman, M.A.J. Somers, W.G. Sloof, E.J. Mittemeijer, and S. van der Zwaag: Z. Metallkd., 1993, vol. 84, pp. 124-31.
14. M.H. Biglari, C.M. Brakman, E.J. Mittemeijer, and S. van der Zwaag: Phil. Mag. A, 1995, vol. 72, pp. 1281-99.10.1080/01418619508236255 ↗
15. M.H. Biglari, C.M. Brakman, E.J. Mittemeijer, and S. van der Zwaag: Metal. Mater. Trans. A, 1995, vol. 26A, pp. 765-76.10.1007/BF02649075 ↗
16. W.D. Welch and S.H.Carpenter: Acta Metall.,1973, vol. 21, pp. 1169-79.10.1016/0001-6160(73)90033-3 ↗
17. A. Krawitz: Scripta Metall., 1977, vol. 11, pp. 117-22.10.1016/0036-9748(77)90289-7 ↗
18. S.S. Hosmani, R.E. Schacherl, and E.J. Mittemeijer: Acta Mater., 2005, vol. 53, pp. 2069-79.10.1016/j.actamat.2005.01.019 ↗
19. S.S. Hosmani, R.E. Schacherl, and E.J. Mittemeijer: Acta Mater., 2006, vol. 54, pp. 2783-92.10.1016/j.actamat.2006.02.017 ↗
20. D.H. Kirkwood, O.E. Atasoy, and S.R. Keown: Metals. Sci., 1974, vol. 8, pp. 49-55.10.1016/0036-9748(74)90438-4 ↗
21. H.H. Podgurski and F.N. Davis: Acta Metall., 1981, vol. 29, pp. 1-9.10.1016/0001-6160(81)90081-X ↗
22. D.S. Rickerby, S. Henderson, A. Hendry, and K.H. Jack: Acta Metall., 1986, vol. 34, pp. 1687-99.10.1016/0001-6160(86)90116-1 ↗
23. D.H. Jack: Acta Metall., 1976, vol. 24, pp. 137-46.10.1016/0001-6160(76)90016-X ↗
24. H. Hasegawa, A. Kimura, and T. Suzuki: J. Vac. Sci. Technol. A, 2000, vol. 18, pp. 1038-40.10.1116/1.582296 ↗
25. S.M. Aouadi, J.A. Chladek, F. Namavar, N. Finnegan, and S.L. Rohde: J. Vac. Sci. Technol. B, 2002, vol. 20, pp. 1967-73.10.1116/1.1503790 ↗
26. M.A. Baker, T.P. Mollart, P.N. Gibson, and W. Gissler: J. Vac. Sci. Technol. A, 1997, vol. 15, pp. 284-91.10.1116/1.580526 ↗
27. J. Vetter, H.J. Scholl, and O. Knotek: Surf. Coat. Technol., 1995, vols. 74-5, pp. 286-91.10.1016/0257-8972(95)08350-2 ↗
28. T. Suzuki, D. Huang, and Y. Ikuhara: Surf. Coat. Technol., 1998, vol. 107, pp. 41-47.10.1016/S0257-8972(98)00550-7 ↗
29. E.C. Bain: Trans. AIME, 1924, vol. 70, pp. 25-46.
30. V.A. Phillips and A.U. Seybolt: Trans. TMS-AIME, 1968, vol. 242, pp. 2415-22.
31. M.A.J. Somers, R.M. Lankreijer, and E.J. Mittemeijer: Phil. Mag. A, 1989, vol. 59, pp. 353-78.10.1080/01418618908205064 ↗
32. E. Lehrer: Z. Elektrochem., 1930, vol. 36, pp. 383-92.
33. R. Hoffmann, E.J. Mittemeijer, and M.A.J. Somers: HTM 51, 1996, pp. 162–69.10.1515/htm-1996-510307 ↗
34. R. Delhez and E.J. Mittemeijer: J. Appl. Cryst., 1975, vol. 8, pp. 609-11.10.1107/S0021889875011466 ↗
35. J.L. Pouchou and F. Pichoir: Rech. Aerosp., 1984, pp. 167–192.
36. A. Armigliato, L. Dori, A. Garulli, and P. Venturi: J. Microsc. Spectrosc. Electron., 1982, vol. 7, pp. 593-603.
37. N.E. Vives Diaz, S.S. Hosmani, R.E. Schacherl, and E.J. Mittemeijer: Acta Mater., 2008, vol. 56, pp. 4137-49.10.1016/j.actamat.2008.04.041 ↗
38. A.R. Clauss, E. Bischoff, R.E. Schacherl, and E.J. Mittemeijer: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 1923-34.10.1007/s11661-009-9865-6 ↗
39. Y. Massiani, P. Gravier, L. Fedrizzi, and F. Marchetti: Thin Solid Films, 1995, vol. 261, pp. 202-08.10.1016/S0040-6090(94)06489-X ↗
40. P. Hones, R. Sanjinés, and F. Lévy: Thin Solid Films, 1998, vol. 332, pp. 240-46.10.1016/S0040-6090(98)00992-4 ↗
41. H.H. Podgurski and H.H. Knechtel: Trans. TMS-AIME, 1969, vol. 245, pp. 1595-1602.
42. M. Nikolussi, A. Leineweber, and E.J. Mittemeijer: Phil. Mag., 2010, vol. 90, pp. 1105-22.10.1080/14786430903292365 ↗
43. K.S. Jung, R.E. Schacherl, E. Bischoff, and E.J. Mittemeijer: Surf. Coat. Technol., 2010, vol. 204, pp. 1942-46.10.1016/j.surfcoat.2009.08.031 ↗