Microstructure–Property Correlation in Low-Si Steel Processed Through Quenching and Nonisothermal Partitioning
Source abstract
Abstract
In the present investigation, an attempt has been made to stabilize austenite by carbon partitioning through quenching and nonisothermal partitioning (Q&P) technique. This will eliminate the need for additional heat-treatment facility to perform isothermal partitioning or tempering process. The presence of retained austenite in the microstructure helps in increasing the toughness, which in turn is expected to improve the abrasion resistance of steels. The carbon partitioning from different quench temperatures has been performed on two different alloys, with low-Si content (0.5 wt pct), in a salt bath furnace atmosphere, the cooling profile of which closely resembles the industrially produced hot-rolled coil cooling. The results show that the stabilization of retained austenite is possible and gives rise to increased work hardening, better impact toughness and abrasive wear loss comparable to that of a fully martensitic microstructure. In contrast, tempered martensite exhibits better wear properties at the expense of impact toughness.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (56)
Show source-provided references
1. J. Speer, D.K. Matlock, B.C. De Cooman, and J.G. Schroth: Acta Mater, 2003, vol. 51, pp. 2611-22.10.1016/S1359-6454(03)00059-4 ↗
2. P.C. Wolfram: MS Thesis,Colorado School of Mines, Golden, Co, 2013.
3. M.C. Somani, D.A. Porter, L.P.Karjalainen, P.P. Suikkanen, and R.D.K. Misra: Mater. Today 2S, 2015, S631-34.10.1016/j.matpr.2015.07.363 ↗
4. X.C. Xiong, B. Chen, M.X. Huang, J.F. Wang, and L. Wang: Scr. Mater, 2013, vol. 68, pp. 321-24.10.1016/j.scriptamat.2012.11.003 ↗
5. N. Maheswari, S.G. Chowdhury, K.C.H. Kumar, and S. Sankaran: Mater. Sci. Eng. A, 2014, vol. 600, pp. 12-20.10.1016/j.msea.2014.01.066 ↗
6. Y. Toji, G. Miyamoto, and D. Raabe: Acta Mater, 2015, vol. 86, pp. 137-47.10.1016/j.actamat.2014.11.049 ↗
7. X. Tan, Y. Xu, X. Yang, Z. Liu, and D. Wu: Mater. Sci. Eng. A, 2014, vol. 594, pp. 149-60.10.1016/j.msea.2013.11.064 ↗
8. M.K. Abian, A.Z. Hanzaki, H.R. Abedi, and S.H. Manesh: Mater. Sci. Eng. A, 2016, vol. 651, pp. 233-40.10.1016/j.msea.2015.10.116 ↗
9. E.P. Bagliani, M.J. Santofimia, L. Zhao, J. Sietsma, and E. Anelli: Mater. Sci. Eng. A, 2013, vol. 559, pp. 486-95.10.1016/j.msea.2012.08.130 ↗
10. S. Yan, X. Liu, W.J. Liu, H. Lan, and H. Wu: Mater. Sci. Eng. A, 2015, vol. 620, pp. 58-66.10.1016/j.msea.2014.09.047 ↗
11. G.A. Thomas: MS Thesis, Colorado School of Mines, Golden, Co, 2009.
12. G.A. Thomas, J.G. Speer, and D.K. Matlock: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 3652-59.10.1007/s11661-011-0648-5 ↗
13. X.D. Tan, Y.B. Xu, X.L. Yang, Z.P. Hu, F. Peng, X.W. Ju, and D. Wu: Mater. Charact., 2015, vol. 104, pp. 23-30.10.1016/j.matchar.2015.03.022 ↗
14. M.J. Neale, and M. Gee: Guide to Wear Problems and Testing for Industry, William Andrew Inc., Norwich 2001.
15. H. Mohrbacher: Molybdenum in steels for abrasion resistant applications, NiobelConbvba, Schilde 2014
16. K. Wasiak, E. Skołek, and W.A. Świątnicki: Metal 2014: 23rd International Conference on Metallurgy and Materials, May 21st–23rd 2014, Brno, Czech Republic, EU.
17. S.G. Liu, S.S. Dong, F. Yang, L. Li, B. Hu, F.H. Xiao, Q. Chen, and H.S. Liu: Mater. Des., 2014, vol. 56, pp. 37-43.10.1016/j.matdes.2013.10.094 ↗
18. K. Jian, W. Chao, L. Yunjie, Y. Guo, and W. Guodong, J. Wuhan Uni. Tech. Mater. Sci. Ed., 2016, vol. 31, pp. 178-8510.1007/s11595-016-1349-0 ↗
19. G.R. Speich: Trans. Metall. Soc. AIME, 1969, vol. 245, pp. 2553-64.
20. A.J. Clarke, M.K. Miller, R.D. Field, D.R. Coughlin, P.J. Gibbs, K.D. Clarke, D.J. Alexander, K.A. Powers, P.A. Papin, and G. Krauss: Acta Mater, 2014, vol. 77, pp. 17-27.10.1016/j.actamat.2014.05.032 ↗
21. E. De Moor, S. Lacroix, L. Samek, J. Penning, and J.G. Speer: The 3rd International Conference on Advanced Structural Steels, Gyeongju, Korea, August 22–24, 2006.
22. B.C. De Cooman: Curr. Opin. Solid State Mater. Sci., 2004, vol. 8, pp. 285-03.10.1016/j.cossms.2004.10.002 ↗
23. L. Suarez, J. Schneider, and Y. Houbaert: Defect and Diffusion Forum, 2008, vol. 273-276, pp. 655-60.10.4028/www.scientific.net/DDF.273-276.655 ↗
24. A. Grajcar: J. Therm. Anal. Calorim., 2014, vol. 118, pp. 1011-20.10.1007/s10973-014-3801-8 ↗
25. E. Abbasi,and W.M.Rainforth: Mater. Sci. Technol., 2017, vol. 33, pp. 311-20.10.1016/j.jmst.2016.08.019 ↗
26. L. Li, H.Yu, C. Song, J. Lu, J. Hu, and T. Zhou: Steel Res. Int., 2017, vol. 88 (5), pp. 1-9.10.1002/srin.201600234 ↗
27. N. Zhong, Y. Wang, K. Zhang, and Y H. Rong: Steel Res. Int., 2011, vol. 82, pp. 1332-37.10.1002/srin.201100125 ↗
28. Y. Wang, Z. Guo, N. Chen, and Y. Rong: Mater. Sci. Technol., 2013, vol. 29, pp. 451-57.10.1016/j.jmst.2013.01.003 ↗
29. Ana LuizaAzevedo de Araújo: MS Thesis, Colorado School of Mines, Golden, Co, 2016.
30. D.K. Matlock, V.E. Bräutigam, and J.G. Speer: Materials Science Forum, 203, vol. 426-432, pp 1089-94.10.4028/www.scientific.net/MSF.426-432.1089 ↗
31. F. Peng, Y. Xu, X. Gu, Y. Wang, X. Liu, and J. Li: Mater. Sci. Eng. A, 2018, vol. 723, pp. 247-58.10.1016/j.msea.2018.03.061 ↗
32. J.G. Speer, A.L. Araujo, D.K. Matlock, and E. De Moor: Mater Sci Forum, 2016, vol. 879, pp 1834-40.10.4028/www.scientific.net/MSF.879.1834 ↗
33. J. Zhang, H. Ding, C. Wang, J. Zhao, and T. Ding: Mater. Sci. Eng. A, 2013, vol. 585, pp. 132-38.10.1016/j.msea.2013.07.046 ↗
34. J. Dearden, and H. O’Neill: Trans. Inst. Weld, 1940, vol. 3, pp. 203-14.
35. K.W. Andrews: J. of the Iron and Steel Inst., 1965, vol. 203, pp. 721-27.
36. P. Jacques, E. Girault, T. Catlin, N. Geerlofs, T. Kop, S.V.D. Zwaag, and F. Delannay: Mater. Sci. Eng. A, 1999, vol. 273-275, pp. 475-79.10.1016/S0921-5093(99)00331-7 ↗
37. J.G. Speer, F.C. Rizzo, D.K. Matlock, and D.V. Edmonds: J. Mater. Res., 2005, vol. 8, pp. 417-23.10.1590/S1516-14392005000400010 ↗
38. E. De Moor, J. Penning, C. Fojer, A.J. Clarke, and J.G. Speer: Int. Conf. on New Developments in Advanced High-Strength Sheet Steels, Orlando, FL, 2008, pp. 199–07.
39. A. Sundström, J. Rendón, and M. Olsson: Wear, 2001, vol. 250, pp. 744-54.10.1016/S0043-1648(01)00712-8 ↗
40. A. Sergey, H. Klaus, S. Andreij, Y. Evgenij, M. Youri, and N. Sergey: Iron & Steel Supplement, The Joint Int. Conf. of HSLA Steels and ISUGS, 2005, vol. 40, pp. 759–63.
41. D.K. Matlock, and J.G. Speer: Mater. Sci. Technol., 2009, vol. 25, pp. 1118-25.10.1179/174328408X322222 ↗
42. M. Korchynsky: The use of Vanadium in Steel—Proc. of the Vanitec Symposium, Beijing, China, Oct. 2001, pp. 26–35
43. G. Krauss: Steels: Processing, Structure, and Performance, ASM International, Metals Park, OH, 2005.
44. N. Ojala, K. Valtonen, V. Heino, M. Kallio, J. Aaltonen, P. Siitonen, and V.T. Kuokkala: Wear, 2014, vol. 317, pp. 225-32.10.1016/j.wear.2014.06.003 ↗
45. J.G. Speer, A.M. Streicher, D.K. Matlock, F. Rizzo, and G. Krauss: Austenite formation and decomposition, TMS/ISS, Warrendale 2003, pp. 505-22
46. S.N. Ghali, H.S. El-Faramawy, and M.M. Eissa: J. Minerals Mater. Charact. Eng., 2012, vol. 11, pp. 995-99.
47. W. Alqhadafi: Master thesis, Luleå University of Technology, 2012.
48. C.E.I.C. Öhlund, J. Weidow, M. Thuvander, and S.E. Offerman: Iron Steel Inst. Jpn. Int., 2014, vol. 54, No. 12, pp. 2890-99.10.2355/isijinternational.54.2890 ↗
49. B.V.N.Rao: Metall. Trans. A, 1979, vol. 10A, pp. 645-48.10.1007/BF02658328 ↗
50. S. Nagakura: J. Phys. Soc. Jpn, 1959, vol. 14, No. 2, pp. 186-95.10.1143/JPSJ.14.186 ↗
51. K. Zhang, M. Zhang, Z. Guo, N. Chen, and Y. Rong: Mater. Sci. Eng. A, 2011, vol. 528, pp. 8486-91.10.1016/j.msea.2011.07.049 ↗
52. G. Gao, H. Zhang, X. Gui, P. Luo, Z. Tan, and B. Bai: Acta Mater., 2014, vol. 76, pp. 425-33.10.1016/j.actamat.2014.05.055 ↗
53. I. Mejía, C. Maldonado, J.A. Benito, J. Jorba, and A. Roca: Mater. Sci. Forum, 2006, vol. 509, pp. 37-42.10.4028/www.scientific.net/MSF.509.37 ↗
54. H.S. Zhao, W. Li, X. Zhu, X.H. Lu, L. Wang, S. Zhou, and X.J. Jin: Mater.Sci. Eng. A, 2016, vol. 649, pp. 18-26.10.1016/j.msea.2015.09.088 ↗
55. X. Huang, W. Liu, Y. Huang, H. Chen, and W. Huang: J. Mater. Processing Technol., 2015, vol. 222, pp. 181-87.10.1016/j.jmatprotec.2015.03.010 ↗
56. M.M. Wang, J.C. Hell, and C.C. Tasan: Scr. Mater, 2017, vol. 138, pp. 1-5.10.1016/j.scriptamat.2017.05.021 ↗