journal article·2011-05

Mechanical Properties and Microstructural Evolution of Friction-Stir-Welded Thin Sheet Aluminum Alloys

Emanuela Cerri, Paola Leo, Xiang Wang, J. D. Embury

Publisher page

Abstract

Friction stir welding of thin aluminum sheets represents a potential goal for aircraft and automotive industries because of the advantages of using this new technological process. In the current work, the microstructural evolution and mechanical behavior of 6082T6-6082T6, 2024T3-2024T3, and 6082T6-2024T3 thin friction-stir-welded joints were investigated. Uniaxial tensile testing at room temperature, 443 K, 473 K, and 503 K (170 °C, 200 °C, and 230 °C) was used to determine the extent to which these ultra-thin joints can be used and deformed. The tensile stress–strain curves showed a decrease of the flow stress with increasing temperature and decreasing strain rate. The ductility of 6082T6-6082T6 joints generally improved when deformed at warm temperatures. It was almost constant for the 6082T6-2024T3 and reached the higher value in the 2024T3-2024T3 when deformed at 443 K and 473 K (170 °C and 200 °C) when compared with the room temperature value. Tensile specimens fractured in the middle of the weld zone in a ductile mode. The precipitation and growth of S’ type phases strengthens 2024T3-2024T3 joints during deformation. In the 6082T6-6082T6, β″ precipitates show some increase in size but give a lower contribution to strength. At 503 K (230 °C), recovery mechanisms (dislocation reorganization inside the deformed grains) are initiated but the temperature was not enough high to produce a homogeneous subgrain structure.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. C.G. Rodes, M.W. Mahoney, W.H. Bingel, R.A. Spurling, and C.C. Bampton: Scripta Mater., 1997, vol. 36, pp. 69-75.10.1016/S1359-6462(96)00344-2 ↗
2. M.W. Mahoney, C.G. Rodes, J.G. Flintoff, R.A. Spurling, and W.H. Bingel: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1955-64.10.1007/s11661-998-0021-5 ↗
3. Y. Sato, H. Kokawa, M. Enomoto, and S. Jogan: Metall. Mater. Trans. A 1999, vol. 30A, pp. 2429-37.10.1007/s11661-999-0251-1 ↗
4. K.V. Jata: Mater. Sci. Forum, 2000, vol. 331-337, pp. 1701-12.10.4028/www.scientific.net/MSF.331-337.1701 ↗
5. R. Braun, C. Dalle Donne, G. Staniek (2000) . Mat. Wiss. u. Werkstofftech., 31:1017-26.10.1002/1521-4052(200012)31:12<1017::AID-MAWE1017>3.0.CO;2-P ↗
6. W.M. Thomas, E.D. Nicholas, J.C. Needam, M.G. Murch, P. Templesmith, and C.J. Dawes: GB Patent application 9125978.8 (1991); 9125978.8, December 1991 and US Patent No. 5460317, October 1995.
7. I. Charit, R.S. Mishra, and M.W. Mahoney: Scripta Mater., 2002, vol. 47, pp. 631-36.10.1016/S1359-6462(02)00257-9 ↗
8. H.G. Salem, A.P. Reynolds, and J.S. Lyons: Scripta Mater., 2002, vol. 46, pp. 337-42.10.1016/S1359-6462(01)01246-5 ↗
9. C.G. Rhodes, M.W. Mahoney, W.H. Bingel, and M. Calabrese: Scripta Mater., 2003, vol. 48, pp. 1451-55.10.1016/S1359-6462(03)00082-4 ↗
10. K.V. Jata and S.L. Semiatin: Scripta Mater., 2000, vol. 43, no. 8, pp. 743-49.10.1016/S1359-6462(00)00480-2 ↗
11. W.D. Lockwood, B. Tomaz, and A.P. Reynolds: Mater. Sci. Eng. A, 2002, vol. 323, pp. 348-53.10.1016/S0921-5093(01)01385-5 ↗
12. M. Guerra, C. Schmidt, J.C. McClure, L.E. Murr, and A.C. Nes: Mater. Charac., 2003, vol. 49, pp. 95-101.10.1016/S1044-5803(02)00362-5 ↗
13. J.Q. Su, T.W. Nelson, R. Mishra, and M. Mahoney: Acta Mater., 2003, vol. 51, pp. 713-29.10.1016/S1359-6454(02)00449-4 ↗
14. C.G. Rhodes, M.W. Mahoney, and W.H. Bingel: Scripta Mater., 1997, vol. 36, pp. 69-75.10.1016/S1359-6462(96)00344-2 ↗
15. G. Liu, L.E. Murr, C.S. Niou, J.C. McClure, and F.R. Vega: Scripta Mater., 1997, vol. 37, pp. 355.10.1016/S1359-6462(97)00093-6 ↗
16. L.E. Murr, G. Liu, and J.C. McClur: J. Mater. Sci. Lett., 1997, vol. 16, p. 1801.10.1023/A:1018556332357 ↗
17. P. Heurtier, C. Desrayaud, and F. Montheillet: Mater. Sci. Forum, 2002, vol. 396-402, p. 1537.10.4028/www.scientific.net/MSF.396-402.1537 ↗
18. P. Bala Srinivasan, W. Dietzel, R. Zettler, J.F. Dos Santos, and V. Sivan: Mater. Sci. Eng. A, 2005, vol. 392, pp. 292-300.10.1016/j.msea.2004.09.065 ↗
19. W.B. Lee, Y.M. Yeon, and S.B. Jung: J. Mater. Sci. Lett., 2003, vol. 38, pp. 4183-91.
20. W.B. Lee, Y.M. Yeon, and S.B. Jung: Scripta Mater., 2003, vol. 49, pp. 423-28.10.1016/S1359-6462(03)00301-4 ↗
21. H. Uzun, C. Dalle Donne, A. Argagnotto, T. Ghidini, and C. Gambaro: Mater. Design, 2005, vol. 26, pp. 41-46.10.1016/j.matdes.2004.04.002 ↗
22. C.M. Chen and R. Kovacevic: Int. J. Mach. Tool. Manuf., 2004, vol. 44, pp. 1203-14.
23. A.C. Somasekharan and L.E. Murr: Mater. Charact., 2004, vol. 52, pp. 49-64.10.1016/j.matchar.2004.03.005 ↗
24. Y. Li, E.A. Trillo, and L.E. Murr: J. Mater. Sci. Lett., 2000, vol. 19, pp. 1047-51.10.1023/A:1006795221194 ↗
25. E. Cerri, P. Leo, P.P. De Marco, D. Embury, and X. Wang: Aluminum Alloys – Their Physical and Mechanical Properties, J. Hirsch, B. Skrotzki, and G. Gottstein, eds., Wiley-VCH, Weinheim, Germany, 2008, pp. 1917–23.
26. A.F. Norman, I. Brough, and P.B. Pragnell: Mater. Sci. Forum, 2000, vols. 331–337, pp. 1713.10.4028/www.scientific.net/MSF.331-337.1713 ↗
27. M.A. Sutton, B. Yang, A.P. Reynolds, and J. Yan: J. Mat. Sci. Eng. A, 2004, vol. 364, p. 66.10.1016/S0921-5093(03)00533-1 ↗
28. R. Nandan, T. DebRoy, and H.K.D.H. Bhadeshia: Prog. Mater. Sci., 2008, vol. 53, pp. 980-1023.10.1016/j.pmatsci.2008.05.001 ↗
29. C. Genevois, D. Fabrègue, A. Deschamps, and W.J. Poole: Mater. Sci. Eng. A, 2006, vol. 441, pp. 39-48.10.1016/j.msea.2006.07.151 ↗
30. A.K. Saad and T. Shibayanagi: Trans. JWRI, 2007, vol. 36, no. 1, pp. 27-40.
31. V. Dixit, R.S. Mishra, R.J. Lederich, and R. Talwar: Report AFRL-ML-WP-TP-2006-468, 2006.