journal article·2021-08

Effect of Ti Addition and Microstructural Evolution on Toughening and Strengthening Behavior of as Cast or Annealed Nb–Si–Mo Based Hypoeutectic and Hypereutectic Alloys

Kasturi Sala, Rahul Mitra

Publisher page

Abstract

Room temperature fracture toughness along with compressive deformation behavior at both room and high temperatures (900 °C, 1000 °C and 1100 °C) has been evaluated for ternary or quaternary hypoeutectic (Nb–12Si–5Mo and Nb–12Si–5Mo–20Ti) and hypereutectic (Nb–19Si–5Mo and Nb–19Si–5Mo–20Ti) Nb-silicide based intermetallic alloys to examine the effects of composition, microstructure, and annealing (100 hours at 1500 °C). On Ti-addition and annealing, the fracture toughness has increased by up to ~ 75 and ~ 63 pct, respectively with ~ 14 MPa√m being recorded for the annealed Nb–12Si–5Mo–20Ti alloy. Toughening is ascribed to formation of non-lamellar eutectic with coarse Nbss, which contributes to crack path tortuosity by bridging, arrest, branching and deflection of cracks. The room temperature compressive strengths are found as ~ 2200 to 2400 MPa for as-cast alloys, and ~ 1700 to 2000 MPa after annealing with the strength reduction being higher for the hypoeutectic compositions due to larger Nbss content. Further, the compressive ductility has varied from 5.7 to 6.5 pct. The fracture surfaces obtained from room temperature compression tests have revealed evidence of brittle failure with cleavage facets and river patterns in Nbss along with its decohesion at non-lamellar eutectic. The compressive yield stress decreases with increase in test temperature, with the hypoeutectic alloys exhibiting higher strength retention indicating the predominant role of solid solution strengthening of Nbss. The flow curves obtained from high temperature compression tests show initial work hardening, followed by a steady state regime indicating dynamic recovery involving the formation of low angle grain boundaries in the Nbss, as confirmed by electron backscattered diffraction of the annealed Nb–12Si–5Mo alloy compression tested at 1100 °C.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Intermetallics and Advanced Alloy Properties · Titanium Alloys Microstructure and Properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (63)

Show source-provided references
1. 1 B.P. Bewlay, J.J. Lewandowksi, and M.R. Jackson: JOM, 1997, vol. 49, pp. 44–5.10.1007/BF02914402 ↗
2. 2 Z. Li and P. Tsakiropoulos: Intermetallics, 2012, vol. 26, pp. 18–25.10.1016/j.intermet.2012.03.051 ↗
3. 3 T. Tanahashi, S. Miura, and T. Mohri: Mater. Res. Soc. Symp. Proc., 2011, vol. 1295, pp. 207–12.10.1557/opl.2011.33 ↗
4. 4 J. Sha, C. Yang, and J. Liu: Scr. Mater., 2010, vol. 62, pp. 859–62.10.1016/j.scriptamat.2010.02.023 ↗
5. 5 Z. Li and P. Tsakiropoulos: J. Alloys Compd., 2013, vol. 550, pp. 553–60.10.1016/j.jallcom.2012.10.170 ↗
6. 6 J. Geng, P. Tsakiropoulos, and G. Shao: Intermetallics, 2007, vol. 15, pp. 69–76.10.1016/j.intermet.2006.03.001 ↗
7. 7 S. Zhang and X. Guo: Intermetallics, 2016, vol. 70, pp. 33–44.10.1016/j.intermet.2015.12.002 ↗
8. 8 I. Grammenos and P. Tsakiropoulos: Intermetallics, 2011, vol. 19, pp. 1612–21.10.1016/j.intermet.2011.06.008 ↗
9. 9 S. Kashyap, C.S. Tiwary, and K. Chattopadhyay: Intermetallics, 2011, vol. 19, pp. 1943–52.10.1016/j.intermet.2011.05.018 ↗
10. 10 J.R. Zhou and J.B. Sha: Intermetallics, 2013, vol. 34, pp. 1–9.10.1016/j.intermet.2012.10.017 ↗
11. 11 K. Chattopadhyay, G. Balachandran, R. Mitra, and K.K. Ray: Intermetallics, 2006, vol. 14, pp. 1452–60.10.1016/j.intermet.2006.01.054 ↗
12. 12 K. Sala and R. Mitra: Mater. Sci. Eng. A, 2021, vol. 802, p. 140663.10.1016/j.msea.2020.140663 ↗
13. R. Ma and X. Guo: Intermetallics, 2021, vol. 129, p. 107053.10.1016/j.intermet.2020.107053 ↗
14. J. Sha, H. Hirai, T. Tabaru, A. Kitahara, H. Ueno, and S. Hanada: Metall. Mater. Trans. A, 2003, vol. 34, pp. 85–94.10.1007/s11661-003-0210-1 ↗
15. K.S. Chan and D.L. Davidson: Metall. Mater. Trans. A, 1999, vol. 30, pp. 925–39.10.1007/s11661-999-0146-1 ↗
16. 16 J.H. Kim, T. Tabaru, H. Hirai, A. Kitahara, and S. Hanada: Scr. Mater., 2003, vol. 48, pp. 1439–44.10.1016/S1359-6462(03)00084-8 ↗
17. 17 J. Sha, H. Hirai, T. Tabaru, A. Kitahara, H. Ueno, and S. Hanada: Mater. Sci. Eng. A, 2004, vol. 364, pp. 151–8.10.1016/j.msea.2003.08.014 ↗
18. J. Zhao and J.H. Westbrook: MRS Bull., 2003, pp. 622–30.10.1557/mrs2003.189 ↗
19. 19 B.P. Bewlay, M.R. Jackson, J.C. Zhao, P.R. Subramanian, M.G. Mendiratta, and J.J. Lewandowski: MRS Bull., 2003, vol. 28, pp. 646–53.10.1557/mrs2003.192 ↗
20. 20 R. Mitra: Int. Mater. Rev., 2006, vol. 51, pp. 13–64.10.1179/174328006X79454 ↗
21. 21 Y. Tang and X. Guo: Scr. Mater., 2016, vol. 116, pp. 16–20.10.1016/j.scriptamat.2016.01.033 ↗
22. 22 A.N. Behera, A. Chaudhuri, R. Kapoor, J.K. Chakravartty, and S. Suwas: Mater. Des., 2016, vol. 92, pp. 750–9.10.1016/j.matdes.2015.12.077 ↗
23. 23 Y.V.R.K. Prasad and T. Seshacharyulu: Int. Mater. Rev., 1998, vol. 43, pp. 243–58.10.1179/imr.1998.43.6.243 ↗
24. 24 C. Mccaughey and P. Tsakiropoulos: Materials (Basel)., 2018, vol. 11, p. 967.10.3390/ma11060967 ↗
25. 25 S. Miura, Y. Murasato, Y. Sekito, Y. Tsutsumi, K. Ohkubo, Y. Kimura, Y. Mishima, and T. Mohri: Mater. Sci. Eng. A, 2009, vol. 510–511, pp. 317–21.10.1016/j.msea.2008.04.123 ↗
26. 26 A. Chaudhuri, A. Sarkar, R. Kapoor, J.K. Chakravartty, R.K. Ray, and S. Suwas: J. Mater. Eng. Perform., 2019, vol. 28, pp. 448–62.10.1007/s11665-018-3799-3 ↗
27. 27 K. Sala, S. Morankar, and R. Mitra: Metall. Mater. Trans. A, 2021, vol. 52, pp. 1185–211.10.1007/s11661-021-06155-2 ↗
28. ASTM-E399: Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness K Ic Of, 2016.
29. 29 K. Chattopadhyay, R. Sinha, R. Mitra, and K.K. Ray: Mater. Sci. Eng. A, 2007, vol. 456, pp. 358–63.10.1016/j.msea.2006.12.023 ↗
30. 30 H. Guo and X. Guo: Scr. Mater., 2011, vol. 64, pp. 637–40.10.1016/j.scriptamat.2010.12.008 ↗
31. 31 L.A.I. Kestens and H. Pirgazi: Mater. Sci. Technol. ISSN, 2016, vol. 32, pp. 1303–15.10.1080/02670836.2016.1231746 ↗
32. 32 A. Chaudhuri, A. Sarkar, R. Kapoor, R.N. Singh, J.K. Chakravartty, and S. Suwas: JOM, 2014, vol. 66, pp. 1923–9.10.1007/s11837-014-1122-9 ↗
33. 33 A. Chaudhuri, A.N. Behera, A. Sarkar, R. Kapoor, R.K. Ray, and S. Suwas: Acta Mater., 2019, vol. 164, pp. 153–64.10.1016/j.actamat.2018.10.037 ↗
34. C. Yang, L. Jia, C. Zhou, H. Zhang, and J. Sha: Metall. Mater. Trans. A, 2014, vol. 45, pp. 4842–50.10.1007/s11661-014-2423-x ↗
35. K.S. Chan: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2315–2810.1007/s11661-003-0295-6 ↗
36. K.S. Chan: Metall. Mater. Trans. A, 2001, vol. 32, pp. 2475–87.10.1007/s11661-001-0037-6 ↗
37. 37 K.S. Chan: Philos. Mag., 2005, vol. 85, pp. 239–59.10.1080/14786430412331315725 ↗
38. 38 K.S. Chan: Mater. Sci. Eng. A, 2005, vol. 409, pp. 257–69.10.1016/j.msea.2005.06.077 ↗
39. 39 K.S. Chan: Mater. Sci. Eng. A, 2002, vol. 329–331, pp. 513–22.10.1016/S0921-5093(01)01502-7 ↗
40. K.S. Chan and D.L. Davidson: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 1833–49.10.1007/s11661-003-0149-2 ↗
41. 41 I. Papadimitriou, C. Utton, A. Scott, and P. Tsakiropoulos: Intermetallics, 2014, vol. 54, pp. 125–32.10.1016/j.intermet.2014.05.020 ↗
42. 42 W. Liu and J.B. Sha: Mater. Des., 2016, vol. 111, pp. 301–11.10.1016/j.matdes.2016.08.087 ↗
43. 43 S. Zhang and X. Guo: Intermetallics, 2015, vol. 57, pp. 83–92.10.1016/j.intermet.2014.10.007 ↗
44. 44 L.N. Jia, J.F. Weng, Z. Li, Z. Hong, L.F. Su, and H. Zhang: Mater. Sci. Eng. A, 2015, vol. 623, pp. 32–7.10.1016/j.msea.2014.11.001 ↗
45. J. Sha, J. Liu, and C. Zhou: Metall. Mater. Trans. A, 2011, vol. 42, pp. 1534–43.10.1007/s11661-010-0549-z ↗
46. 46 L. Su, L. Jia, S. Yuan, L. Zhou, H. Zhang, and H. Zhang: Mater. Sci. Technol., 2015, vol. 31, pp. 220–4.10.1179/1743284714Y.0000000506 ↗
47. 47 B. Guo and X. Guo: Mater. Sci. Eng. A, 2014, vol. 617, pp. 39–45.10.1016/j.msea.2014.08.009 ↗
48. 48 Y. Huang, L. Jia, Z. Jin, B. Kong, Y. Guo, J. Sha, and H. Zhang: Mater. Des., 2018, vol. 160, pp. 671–82.10.1016/j.matdes.2018.10.001 ↗
49. 49 Y. Yan, H. Ding, Y. Kang, and J. Song: Mater. Des., 2014, vol. 55, pp. 450–5.10.1016/j.matdes.2013.10.017 ↗
50. 50 Y. Qiao, X. Guo, and Y. Zeng: Intermetallics, 2017, vol. 88, pp. 19–27.10.1016/j.intermet.2017.04.008 ↗
51. 51 Y. Kang, S. Qu, J. Song, Q. Huang, and Y. Han: Mater. Sci. Eng. A, 2012, vol. 534, pp. 323–8.10.1016/j.msea.2011.11.076 ↗
52. 52 G.M. Cheng and L.L. He: Intermetallics, 2011, vol. 19, pp. 196–201.10.1016/j.intermet.2010.08.015 ↗
53. 53 N. Sekido, Y. Kimura, S. Miura, F.G. Wei, and Y. Mishima: J. Alloys Compd., 2006, vol. 425, pp. 223–9.10.1016/j.jallcom.2006.01.071 ↗
54. 54 S.M. Zhang, J.R. Zhou, and J.B. Sha: Intermetallics, 2015, vol. 57, pp. 146–55.10.1016/j.intermet.2014.10.013 ↗
55. 55 J.T. Guo, Y.X. Tian, G.M. Cheng, L.Z. Zhou, L.L. He, and H.Q. Ye: J. Alloys Compd., 2009, vol. 470, pp. 606–9.10.1016/j.jallcom.2008.03.036 ↗
56. 56 Y.X. Tian, J.T. Guo, G.M. Cheng, L.Y. Sheng, L.Z. Zhou, L.L. He, and H.Q. Ye: Mater. Des., 2009, vol. 30, pp. 2274–7.10.1016/j.matdes.2008.08.016 ↗
57. 57 Y.X. Tian, J.T. Guo, L.Y. Sheng, G.M. Cheng, L.Z. Zhou, L.L. He, and H.Q. Ye: Intermetallics, 2008, vol. 16, pp. 807–12.10.1016/j.intermet.2008.03.005 ↗
58. R.E. Reedhill: Physical Metallurgy Principles, Second Aff., (published with permission from Litton Educational Publishing Inc., New York, NY), 1973.
59. F.F. Schmidt and H.R. Odgen: Defense Metals Information Center Battelle Memorial Institute Columbus 1, Ohio, 1963, p. A-12, A-16.
60. 60 Anders, F. J., Pollock, W. 1: Tensile Properties and Rolling Textures of Niobium Sheet, The Technology of Columbium (Niobium), John Wiley, New York, 1958.
61. T.H. Courtney: Mechanical Behavior of Materials, McGraw-Hill Publishing Company, New York, Chapter 4, 1990, pp. 137–61.
62. S. Prasad and A. Paul: Defect Diffus. Forum, 2012, vol. 323–325, pp. 491–6.10.4028/www.scientific.net/DDF.323-325.491 ↗
63. D.L. Davidson and K.S. Chan: Metall. Mater. Trans. A, 1999, vol. 30, pp. 2007–18.10.1007/s11661-999-0011-2 ↗