The Computational Design of W and Co-Containing Creep-Resistant Steels with Barely Coarsening Laves Phase and M23C6 as the Strengthening Precipitates
Source abstract
Abstract
Generally, Laves phase and M23C6 are regarded as undesirable phases in creep-resistant steels due to their very high-coarsening rates and the resulting depletion of beneficial alloying elements from the matrix. In this study, a computational alloy design approach is presented to develop martensitic steels strengthened by Laves phase and/or M23C6, for which the coarsening rates are tailored such that they are at least one order of magnitude lower than those in existing alloys. Their volume fractions are optimized by tuning the chemical composition in parallel. The composition domain covering 10 alloying elements at realistic levels is searched by a genetic algorithm to explore the full potential of simultaneous maximization of the volume fraction and minimization of the precipitates coarsening rate. The calculations show that Co and W can drastically reduce the coarsening rate of Laves and M23C6 and yield high-volume fractions of precipitates. Mo on the other hand was shown to have a minimal effect on coarsening. The strengthening effects of Laves phase and M23C6 in the newly designed alloys are compared to existing counterparts, showing substantially higher precipitation-strengthening contributions especially after a long service time. New alloys were designed in which both Laves phase and M23C6 precipitates act as strengthening precipitates. Successfully combining MX and M23C6 was found to be impossible.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (31)
Show source-provided references
1. M. Taneike, F. Abe and K. Sawada: Nature 2003, vol. 424, pp. 294–96.10.1038/nature01740 ↗
2. D. Rojas, J. Garcia, O. Prat, G. Sauthoff and A. R. Kaysser-Pyzalla: Mater. Sci. Eng. A 2011, vol. 528, pp. 5164–76.10.1016/j.msea.2011.03.037 ↗
3. F. S. Yin and W. S. Jung: Metall. Mater. Trans. A 2008, vol. 40A, pp. 302-309.
4. O. Prat, J. Garcia, D. Rojas, C. Carrasco and A. R. Kaysser-Pyzalla: Mater. Sci. Eng., A 2010, vol. 527, pp. 5976–83.10.1016/j.msea.2010.05.084 ↗
5. Å. Gustafson and M. Hättestrand: Mater. Sci. Eng., A 2002, vol. 333, pp. 279–86.10.1016/S0921-5093(01)01874-3 ↗
6. F. Abe, T. Horiuchi, M. Taneike and K. Sawada: Mater. Sci. Eng. A 2004, vol. 378, pp. 299–303.10.1016/j.msea.2003.11.073 ↗
7. Å. Gustafson and J. Ågren: ISIJ Int. 2001, vol. 41, pp. 356–60.10.2355/isijinternational.41.356 ↗
8. A. Kipelova, M. Odnobokova, A. Belyakov and R. Kaibyshev: Metall. Mater. Trans. A 2013, vol. 44A, pp. 577–83.10.1007/s11661-012-1390-3 ↗
9. F. Abe: Mater. Sci. Eng. A 2004, vol. 387–389, pp. 565–69.10.1016/j.msea.2004.01.057 ↗
10. F. Liu, D. H. R. Fors, A. Golpayegani, H. O. Andrén and G. Wahnström: Metall. Mater. Trans. A 2012, vol. 43A, pp. 4053–62.10.1007/s11661-012-1205-6 ↗
11. F. Abe: Mater. Sci. Eng. A 2001, vol. 319-321, pp. 770–73.10.1016/S0921-5093(00)02002-5 ↗
12. F. Abe (2005) Metall. Mater. Trans. A 36:321–32.10.1007/s11661-005-0305-y ↗
13. Y. Yamamoto, M. Takeyama, Z. P. Lu, C. T. Liu, N. D. Evans, P. J. Maziasz and M. P. Brady: Intermetallics 2008, vol. 16, pp. 453–62.10.1016/j.intermet.2007.12.005 ↗
14. B. Kuhn, M. Talik, L. Niewolak, J. Zurek, H. Hattendorf, P. J. Ennis, W. J. Quadakkers, T. Beck and L. Singheiser: Mater. Sci. Eng. A 2014, vol. 594, pp. 372–80.10.1016/j.msea.2013.11.048 ↗
15. I. Tarigan, K. Kurata, N. Takata, T. Matsuo and M. Takeyama: Mater. Res. Soc. Symp. Proc., pp. 317–22.
16. K. Kimura, K. Seki, Y. Toda and F. Abe: ISIJ Int. 2001, vol. 41, pp. S121–25.10.2355/isijinternational.41.Suppl_S121 ↗
17. Y. Toda, H. Tohyama, H. Kushima, K. Kimura and F. Abe: JSME Int. J. Ser. A, vol. 48, pp. 125–31.10.1299/jsmea.48.125 ↗
18. F. Masuyama: ISIJ Int. 2001, vol. 41, pp. 612–25.10.2355/isijinternational.41.612 ↗
19. Q. Lu, W. Xu, and S. van der Zwaag: Comput. Mater. Sci. 2014, vol. 84, 198–205.10.1016/j.commatsci.2013.12.009 ↗
20. Q. Lu, W. Xu, and S. van der Zwaag: Acta Mater. 2014, vol. 64, pp. 133–43.10.1016/j.actamat.2013.10.004 ↗
21. W. Xu, P. E. J. Rivera-Díaz-del-Castillo, W. Wang, K. Yang, V. Bliznuk, L. A. I. Kestens and S. van der Zwaag: Acta Mater. 2010, vol. 58, pp. 3582–93.10.1016/j.actamat.2010.02.028 ↗
22. W. Xu, P. E. J. Rivera-Díaz-del-Castillo and S. van der Zwaag: Comput. Mater. Sci. 2008, vol. 44, pp. 678–89.10.1016/j.commatsci.2008.05.003 ↗
23. K. Ishida: J. Alloys Compd. 1995, vol. 220, pp. 126–31.10.1016/0925-8388(94)06002-9 ↗
24. E. Orowan: Theory of dislocation bowing. (Institute of Metals Symposium on Internal Stresses in Metals and Alloys, London, 1948), pp. 451.
25. A. Kelly: Philos. Mag. 1958, vol. 3, pp. 1472–74.10.1080/14786435808233338 ↗
26. J. Ågren, M. T. Clavaguera-Mora, J. Golczewski, G. Inden, H. Kumar and C. Sigli: Calphad-Comput. Coupling Phase Diagr. Thermochem. 2000, vol. 24, pp. 41-54.10.1016/S0364-5916(00)00014-6 ↗
27. R. W. Cahn, P. Haasen: Physical Metallurgy. (Elsevier, Amsterdam, North-Holland, 1996).
28. J. Hald and L. Korcakova: ISIJ Int. 2003, vol. 43, pp. 420-427.10.2355/isijinternational.43.420 ↗
29. A. Kostka, K. G. Tak, R. J. Hellmig, Y. Estrin and G. Eggeler: Acta Mater. 2007, vol. 55, pp. 539–50.10.1016/j.actamat.2006.08.046 ↗
30. M. Shibuya, Y. Toda, K. Sawada, H. Kushima and K. Kimura: Mater. Sci. Eng. A 2011, vol. 528, pp. 5387–93.10.1016/j.msea.2011.03.088 ↗
31. W. Xu and S. van der Zwaag: ISIJ Int. 2011, vol. 51, pp. 1005–10.10.2355/isijinternational.51.1005 ↗