Tensile, Fatigue, and Creep Properties of Aluminum Heat Exchanger Tube Alloys for Temperatures from 293 K to 573 K (20 °C to 300 °C)
Source abstract
Abstract
Abstract Since automotive heat exchangers are operated at varying temperatures and under varying pressures, both static and dynamic mechanical properties should be known at different temperatures. Tubes are the most critical part of the most heat exchangers made from aluminum brazing sheet. We present tensile test, stress amplitude-fatigue life, and creep–rupture data of six AA3XXX series tube alloys after simulated brazing for temperatures ranging from 293 K to 573 K (20 °C to 300 °C). While correlations between several mechanical properties are strong, ranking of alloys according to one property cannot be safely deduced from the known ranking according to another property. The relative reduction in creep strength with increasing temperature is very similar for all six alloys, but the general trends are also strong with respect to tensile and fatigue properties; an exception is one alloy that exhibits strong Mg-Si precipitation activity during fatigue testing at elevated temperatures. Interrupted fatigue tests indicated that the crack growth time is negligible compared to the crack initiation time. Fatigue lifetimes are reduced by creep processes for temperatures above approximately 423 K (150 °C). When mechanical properties were measured at several temperatures, interpolation to other temperatures within the same temperature range was possible in most cases, using simple and well-established equations.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. J. Hirsch, ed.: Virtual Fabrication of Aluminum Products, WILEY-VCH, Weinheim, 2006, pp. 19–26.
2. ASM: Vol. 19, Fatigue and Fracture, ASM International, Materials Park, OH, U.S.A., 1996.
3. S. Meijers, A. Wittebrood, S. Desikan, and K. Vieregge: AFC Holcroft Brazing Seminar, 2005.
4. Low-Temperature-Joining-Committee: Welding International, vol. 22, 2008, pp. 669–75.10.1080/09507110802460952 ↗
5. S. Kahl, J. Zajac, and H.-E. Ekström: 13th International Conference on Aluminum Alloys, 2012.
6. A. Buteri, J.-Y. Buffière, D. Fabrègue, E. Perrin, J. Rethoré, and P. Havet: 12 th International Conference on Aluminium Alloys, 2010, pp. 338–44.
7. X.X. Yao, R. Sandström, T. Stenqvist, Mater. Sci. Eng. A, 1999, vol. 267, pp. 1–6.10.1016/S0921-5093(99)00062-3 ↗
8. H. Hatta, S. Matsuda, H. Yoshida, Sumitomo Light Met. Tech. Rep., 2008, vol. 49, pp. 24–29.
9. H.H. Kim, S.B. Lee, J. Mech. Sci. Technol., 2012, vol. 26, pp. 2111–15.10.1007/s12206-012-0525-1 ↗
10. R-Development-Core-Team: R: A Language and Environment for Statistical Computing, R Foundation for Statistical Computing, Vienna, Austria, 2009.
11. K. Velten, Mathematical Modeling and Simulation, Wiley-VCH Verlag, Weinheim, Germany, 2009.
12. G.E. Dieter, Mechanical metallurgy, McGraw-Hill Book Company, Singapore, 1988.
13. L. Blaz, E. Evangelista, Mater. Sci. Eng. A, 1996, vol. 207, pp. 195–201.10.1016/0921-5093(95)10038-5 ↗
14. S.L. Semiatin, N. Frey, N.D. Walker, J.J. Jonas, Acta Metall., 1986, vol. 34, pp. 167–76.10.1016/0001-6160(86)90244-0 ↗
15. N. Abedrabbo, F. Pourboghrat, J. Carsley, Int. J. Plast., 2006, vol. 22, pp. 314–41.10.1016/j.ijplas.2005.03.005 ↗
16. Deutsche-Gesellschaft-für-Metallkunde: Atlas der Warmformgebungseigenschaften von Nichteisenmetallen: Aluminiumwerkstoffe, Aluminium-Verlag, Oberursel, Germany, 1978.
17. Q. Zhao: Doctoral Thesis, Norwegian University of Science and Technology, Trondheim, Norway, 2013.
18. W.F. Hosford, J.L. Duncan, J. Met., 1999, vol. 51, pp. 39–44.
19. Y. Bergstrom, Mater. Sci. Eng., 1970, vol. 5, pp. 193–200.10.1016/0025-5416(70)90081-9 ↗
20. F.J. Humphreys, M. Hatherly, Recrystallization and related annealing phenomena, Elsevier, Oxford, U.K., 2004.
21. Y. Bergstrom, Y. Granbom, and D. Sterkenburg: J. Metall., 2010, article ID 647198, pp. 1–16.10.1155/2010/647198 ↗
22. K. Bång: M. Sc. Thesis, Royal Institute of Technology, Stockholm. Sweden, 2011.
23. H.-E. Ekström, Unpublished research, 2003.10.1093/gao/9781884446054.article.T025781 ↗
24. J. Kohout, Fatigue Fract. Eng. Mater. Struct., 2000, vol. 23, pp. 969–77.10.1046/j.1460-2695.2000.00276.x ↗
25. P. Juijerm, I. Altenberger, Scripta Mater., 2006, vol. 55, pp. 943–46.10.1016/j.scriptamat.2006.07.030 ↗
26. T. Saito, S. Muraishi, C.D. Marioara, and R. Holmestad: 13th International Conference on Aluminium Alloys, 2012.
27. J. Kanesund and S. Johansson: 13th International Conference on Aluminium Alloys, 2012.
28. K. Teichmann, C.D. Marioara, K.O. Pedersen, K. Marthinsen, Mater. Sci. Eng. A, 2013, vol. 565, pp. 228–35.10.1016/j.msea.2012.12.042 ↗
29. R.I. Stephens, A. Fatemi, R.R. Stephens, H.O. Fuchs, Metal fatigue in engineering, John Wiley & Sons, New York, U.S.A., 2001.
30. P. Juijerm, U. Noster, I. Altenberger, B. Scholtes, Mater. Sci. Eng. A, 2004, vol. 379, pp. 286–92.10.1016/j.msea.2004.02.022 ↗
31. F.R. Larson, J.A. Miller, Trans. ASME, 1952, vol. 74, pp. 765–75.
32. A.K. Mukherjee, J.E. Bird, J.E. Dorn, Trans. Am. Soc. Met., 1969, vol. 62, pp. 155–79.
33. E. Nes, Scripta Metall. Mater., 1995, vol. 33, pp. 225–31.10.1016/0956-716X(95)00103-3 ↗
34. A.K. Mukherjee, Mater. Sci. Eng. A, 2002, vol. 322, pp. 1–22.10.1016/S0921-5093(01)01115-7 ↗
35. F.C. Monkman, N.J. Grant, Proc. ASTM, 1956, vol. 56, pp. 593–620.
36. J.G. Kaufman, Properties of Aluminum Alloys: Tensile, Creep, and Fatigue Data at High and Low Temperatures, ASM International, Materials Park, OH, U.S.A., 1999.
37. L.F. Mondolfo, Aluminium alloys: structure and properties, Butter Worths, London, U.K., 1976.
38. Y. Du, Y.A. Chang, B.Y. Huang, W.P. Gong, Z.P. Jin, H.H. Xu, Z.H. Yuan, Y. Liu, Y.H. He, F.Y. Xie, Mater. Sci. Eng. A, 2003, vol. 363, pp. 140–51.10.1016/S0921-5093(03)00624-5 ↗
39. Q. Zhao, B. Holmedal, and Y. Li: Philos. Mag., 2013, DOI:10.1080/14786435.2013.794315, pp. 1–17.10.1080/14786435.2013.794315 ↗
40. W.L. Bradley, D.K. Matlock, W. Nam, Metall. Trans. A, 1976, vol. 7A, pp. 425–30.10.1007/BF02642839 ↗
41. D.H. Shin, S.W. Nam, J. Korean Inst. Met., 1983, vol. 21, pp. 628–34.
42. Z.A. Yang, Z.G. Wang, Mater. Sci. Eng. A, 1991, vol. 142, pp. 25–33.10.1016/0921-5093(91)90750-H ↗
43. Z.A. Yang, Z. Wang, X. Hu, Z. Wang, Acta Metall. Mater., 1993, vol. 41, pp. 933–40.10.1016/0956-7151(93)90027-P ↗
44. D.K. Shetty, M. Meshii, Metall. Trans. A, 1975, vol. 6, pp. 349–58.10.1007/BF02667289 ↗
45. N.E. Dowling, C.A. Calhoun, A. Arcari, Fatigue Fract. Eng. Mater. Struct., 2009, vol. 32, pp. 163–79.10.1111/j.1460-2695.2008.01322.x ↗