Room Temperature Shear Band Development in Highly Twinned Wrought Magnesium AZ31B Sheet
Source abstract
Abstract
Failure mechanisms were studied in wrought AZ31B magnesium alloy after forming under different strain paths. Optical micrographs were used to observe the shear band formation and regions of high twin density in samples strained under uniaxial, biaxial, and plane strain conditions. Interrupted testing at 4 pct effective strain increments, until failure, was used to observe the evolution of the microstructure. The results showed that shear bands, with a high percentage of twinned grains, appeared early in the samples strained under biaxial or plane strain tension. These bands are similar to those seen in uniaxial tension specimens just prior to failure where the uniaxial tensile ductility was much greater than that observed for plane strain or biaxial tension conditions. A forming limit diagram for AZ31B, which was developed from the strain data, showed that plane strain and biaxial tension had very similar limit strains; this contrasts with materials like steel or aluminum alloys, which typically have greater ductility in biaxial tension compared to plane strain tension.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (23)
Show source-provided references
1. Barnett, M.R., Twinning and the ductility of magnesium alloys: Part I: ‘Tension’ twins. Materials Science and Engineering: A, 2007. 464(1-2): p. 1-7.10.1016/j.msea.2006.12.037 ↗
2. S.R. Agnew, J.A. Horton, M.H. Yoo, Transmission Electron Microscopy of Dislocations in Mg and Alpha-Solid Solutions of Mg-Li Alloys. Metallurgical and Materials Transactions A, 2002. 33A: p. 851-858.10.1007/s11661-002-0154-x ↗
3. Chang, L.L., E.F. Shang, Y.N. Wang, X. Zhao, M. Qi: Texture and microstructure evolution in cold rolled AZ31 magnesium alloy. Materials Characterization, 2009. 60(6): p. 487-491.10.1016/j.matchar.2008.12.003 ↗
4. J. Jiang, A. Godfreyb, Q. Liu, Microstructure and texture evolution during warm compression of the magnesium alloy AZ31. Science in China Series E: Technological Sciences, 2009. 52: p. 186-189.10.1007/s11431-008-0292-5 ↗
5. H.T. Jeong, T.K. Ha, Texture development in a warm rolled AZ31 magnesium alloy. Journal of Materials Processing Technology, 2007. 187: p. 559-561.10.1016/j.jmatprotec.2006.11.084 ↗
6. Kim, I. and S. Akramov, The development of microstructure and texture in cold rolled AZ31B Mg alloy sheets. International Journal of Modern Physics B, 2008. 22(31-32): p. 5925-5930.10.1142/S0217979208051388 ↗
7. Chen, F.-K. and T.-B. Huang, Formability of stamping magnesium-alloy AZ31 sheets. Journal of Materials Processing Technology, 2003. 142(3): p. 643-647.10.1016/S0924-0136(03)00684-8 ↗
8. Jager, A., P. Luka, V. Gartnerova, J. Bohlen, K.U. Kainer: Tensile properties of hot rolled AZ31 Mg alloy sheets at elevated temperatures. Journal of Alloys and Compounds, 2004. 378(1-2): p. 184-187.10.1016/j.jallcom.2003.11.173 ↗
9. Ayres, R.A., W.G. Brazier, and V.F. Sajewski, Evaluating the GMR-limiting dome height test as a new measure of press formability near plane strain. Journal of Applied Metalworking, 1979. 1(1): p. 41-49.10.1007/BF02833958 ↗
10. Li, H., E. Hsu, J. Szpunar, R. Verma, J.T. Carter: Determination of Active Slip/Twinning Modes in AZ31 Mg Alloy Near Room Temperature. JMEPEG, 2007. 16(321-326).10.1007/s11665-007-9051-1 ↗
11. Kim, B.H., J. Do, S. Lee, I. Park: In situ fracture observation and fracture toughness analysis of squeeze cast AZ51-xSn magnesium alloys. Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing, 2010. 527(24-25): p. 6745-6757.10.1016/j.msea.2010.07.016 ↗
12. M. Barnett, Twinning and the ductility of magnesium alloys Part II Contraction twins. Mater. Sci. Eng A, 2007. 464: p. 8-16.10.1016/j.msea.2007.02.109 ↗
13. Al-Samman, T. and G. Gottstein, Room temperature formability of a magnesium AZ31 alloy: Examining the role of texture on the deformation mechanisms. Materials Science and Engineering A, 2008. 488: p. 406-414.10.1016/j.msea.2007.11.056 ↗
14. Li, X., P. Yang, L.‐N. Wang, L. Meng, F. Cui: Orientational analysis of static recrystallization at compression twins in a magnesium alloy AZ31. Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing, 2009. 517(1-2): p. 160-169.10.1016/j.msea.2009.03.045 ↗
15. M.P. Miles, D. Fullwood, B.L. Adams, A. Khosravani, J. Scott, S. Rogers, and R.K. Mishra: Formability of Wrought Magnesium Sheet for Various Temperatures and Strain Conditions, International Automotive Body Congress (IABC), 2010, Detroit.
16. Barnett MR, Nave MD, Bettles CJ (2004) Mater. Sci. Eng. A 386:205–11.10.1016/S0921-5093(04)00942-6 ↗
17. J. Kang, D.S. Wilkinson, and R.K. Mishra: Inhomogeneous deformation of AZ31B Magnesium Sheet in Uniaxial Tension, Magnesium Technology 2011, Wiley, New York, 2011.10.1002/9781118062029.ch58 ↗
18. M.P. Miles, D. Fullwood, B.L. Adams, A. Khosravani, J. Scott, S. Rogers, R.K. Mishra: J. Mater. Eng. Perform., 2011, vol. 20 (8), pp. 1357–63.10.1007/s11665-011-9897-0 ↗
19. 3D Optical Measurement System, Trilion Quality Systems, Plymouth Meeting, PA.
20. Rezaee-Bazzaz, A., H. Noori, and R. Mahmudi, Calculation of forming limit diagrams using Hill’s 1993 yield criterion. International Journal of Mechanical Sciences, 2011. 53(4): p. 262-270.10.1016/j.ijmecsci.2011.01.007 ↗
21. B. Taylor: Formability Testing of Sheet Metals, ASM Handbook, 2006, vol. 14B, pp. 673–96.10.31399/asm.hb.v14b.a0005149 ↗
22. Butuc MC, Gracio JJ, da Rocha AB (2003) J Mater Process Technol 142(3):714–724.10.1016/S0924-0136(03)00813-6 ↗
23. Chino, Y., K. Kimura, and M. Mabuchi, Deformation characteristics at room temperature under biaxial tensile stress in textured AZ31 Mg alloy sheets. Acta Materialia, 2009. 57(5): p. 1476-1485.10.1016/j.actamat.2008.11.033 ↗