Tensile and Thermal Properties in Compacted Graphite Irons at Elevated Temperatures
Source abstract
Abstract
Tensile and thermal properties of compacted graphite irons (CGIs), prepared with various molybdenum additions and solidification rates, have been investigated for temperatures between room temperature and 873 K (600 °C). A slower solidification rate resulted in larger and fewer graphite particles as well as in an increase of intercellular cementite, or carbides. Molybdenum is a carbide stabilizing element; i.e., increasing additions of molybdenum increased the amount of carbides. Young’s modulus decreased with increasing temperature, and a lower solidification rate increased this parameter slightly. Both increasing content of carbide and increasing nodularity increased the Young’s modulus. Strength parameters such as yield strength and ultimate tensile strength (R m ) were affected in similar ways by temperature and solidification rate. The strength values were generally quite temperature independent for temperatures below 573 K (300 °C) but decreased rapidly for higher temperatures. Increasing nodularity increased the strength, while increasing content of carbide had little influence on the values. The thermal conductivity decreased with increasing content of carbide and increasing nodularity. The thermal conductivity generally showed a maximum value at 573 K (300 °C). A contradictory linear relationship was found between yield strength and thermal conductivity.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Graphite, nuclear technology, radiation studies · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. S. Kim, S.L. Cockcroft, A.M. Omran, and H. Hwang: J. Alloys Compd., 2009, vol. 487 (1–2), pp. 253–57.10.1016/j.jallcom.2009.07.098 ↗
2. C.G. Chao, T.S. Lui, and M.H. Hon: J. Mater. Sci., 1989, vol. 24 (7), pp. 2610–14.10.1007/BF01174533 ↗
3. K.B. Palmer: Iron Steel, 1971, vol. 44 (1), pp. 39–46.
4. M.C. Rukadikar and G.P. Reddy: Transactions of the American Foundrymen's Society and the 93rd Annual Castings Congress, San Antonio, TX, AFS, Des Plaines, IL, 1989, pp. 351–60.
5. C.E. Spaeder, Jr.: ASME, New York, NY, 1979, pp. 27–55.
6. K. Chijiiwa and M. Hayashi: J. Faculty Eng., Univ. Tokyo, Ser. B, 1979, vol. 35 (2), pp. 205–30.
7. W. Shenqing: Trans. Jpn. Foundrymen's Soc. (Jpn.), 1994, vol. 13, pp. 13–17.
8. S. Dawson: Werkstoff und Automobilantrieb, Dresden, Germany, VDI Berichte, Germany, 1999, pp. 85–105.
9. M. König and M. Wessén: Int. J. Cast Met. Res., 2010, vol. 23 (2), pp. 97–110.10.1179/136404609X12505973098972 ↗
10. M. Selin and M. König: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 3235–44.10.1007/s11661-009-0042-8 ↗
11. Y.H. Shy, C.H. Hsu, S.C. Lee, and C.Y. Hou: Mater. Sci. Eng. A, 2000, vol. 278 (1–2), pp. 54–60.10.1016/S0921-5093(99)00599-7 ↗
12. S. Dawson: Transactions of the American Foundrymen's Society and the 106th Annual Castings Congress, Kansas City, MO, AFS, Des Plaines, IL, 2002, pp. 1–11.
13. W.J. Parker, R.J. Jenkins, C.P. Butler, and G.L. Abbott: J. Appl. Phys., 1961, vol. 32 (9), pp. 1679–84.10.1063/1.1728417 ↗
14. D. Holmgren, A. Diószegi, and I.L. Svensson: Tsinghua Sci. Technol., 2008, vol. 13 (2), pp. 80–85.10.1016/S1007-0214(08)70030-0 ↗
15. R.W. Monroe and C.E. Bates: Transactions of the American Foundrymen's Society and the 86th Annual Castings Congress, Chicago, IL, AFS, Des Plaines, IL, 1982, pp. 615–24.
16. J.F. Janowak and R.B. Gundlach: Transactions of the American Foundrymen's Society and the 86th Annual Castings Congress, Chicago, IL, AFS, Des Plaines, IL, 1982, pp. 847–63.
17. B.V. Kovacs: Transactions of the American Foundrymen's Society and the 98th Annual Castings Congress, Hamilton, ON, Canada, AFS, Des Plaines, IL, 1994, pp. 417–20.
18. T.N. Rouns and K.B. Rundman: Transactions of the American Foundrymen's Society and the 91st Annual Castings Congress, St. Louis, MO, AFS, Des Plaines, IL, 1987, pp. 851–74.
19. H. Bayati and R. Elliott: Mater. Manufact. Process., 1997, vol. 12 (1), pp. 1–16.10.1080/10426919708935115 ↗
20. K.L. Hayrynen, D.J. Moore, and K.B. Rundman: Transactions of the American Foundrymen's Society and the 102nd Annual Castings Congress, Atlanta, GA, AFS, Des Plaines, IL, 1998, pp. 665–71.
21. M. Ferry and W. Xu: Mater. Characterization, 2004, vol. 53 (1), pp. 43–49.10.1016/j.matchar.2004.07.008 ↗
22. D. Löhe, O. Vöhringer, and E. Macherauch: Strength of Metals and Alloys (ICSMA 6), Melbourne, Australia, 1982, pp. 199–204.10.1016/B978-1-4832-8423-1.50036-5 ↗
23. N. Ridley: Metall. Mater. Trans. A, 1983, vol. 15A, pp. 1019–36.
24. E.M. Taleff, C.K. Syn, D.R. Lesuer, and O.D. Sherby: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 111–18.10.1007/BF02647751 ↗
25. D. Holmgren, A. Diószegi, and I.L. Svensson: Int. J. Cast Met. Res., 2007, vol. 20 (1), pp. 30–40.10.1179/136404607X202690 ↗
26. M. Selin, D. Holmgren, M. Rinvall, and I.L. Svensson: Giesserei, 2008, vol. 60 (3), pp. 20–25.
27. H. Bayati and R. Elliott: Mater. Sci. Technol., 1999, vol. 15 (3), pp. 265–77.10.1179/026708399101505833 ↗
28. D. Holmgren: Int. J. Cast Met. Res., 2005, vol. 18 (6), pp. 331–4510.1179/136404605225023153 ↗
29. P.C. Liu and C.R. Loper, Jr.: Scan. Electron Micros., Chicago, IL, 1980, pp. 407–18.
30. D. Holmgren, R. Källbom and I.L. Svensson: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 268–75.10.1007/s11661-006-9016-2 ↗